ASD-STAN PREN 4840-002-2017 Aerospace series Heat shrinkable moulded shapes Part 002 Index of product standards and product dimensions (Edition P 1).pdf

1、ASD-STAN STANDARD NORME ASD-STAN ASD-STAN NORM ASD-STAN prEN 4840-002 Edition P 1 November 2017 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. 32 2 775 8126 - Fax. 32 2 775 8131 - www.asd-stan.org ICS: Descriptors: ENG

2、LISH VERSION Aerospace series Heat shrinkable moulded shapes Part 002: Index of product standards and product dimensions Luft- und Raumfahrt Wrmeschrumpfende Bauteile Teil 002: bersicht ber die Produktnormen und Produktabmessungen Srie arospatiale Manchons thermortractables Partie 002 : Index des no

3、rmes de produits et dimensions du produit This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technical

4、ly approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After e

5、xamination and review by users and formal agreement of ASD-STAN, the ASD-STAN prEN will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement

6、the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. ASD-STAN Technical Committee approves that: “This document is published by ASD-STAN for the needs of the European Aerospace Industry. The use of this standar

7、d is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” ASD-STAN reviews each standard and technical report at least every five years at which time it may be revised, reaffirm

8、ed, stabilized or cancelled. ASD-STAN invites you to send your written comments or any suggestions that may arise. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, reco

9、rding, or otherwise, without prior written permission of ASD-STAN. Order details: E-mail: salesasd-stan.org Web address: http:/www.asd-stan.org/ Edition approved for publication 1st November 2017 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Co

10、pyright 2017 ASD-STAN prEN 4840-002:2017 (E) 2 Contents Page Foreword 2 1 Scope 3 2 Normative references 3 3 List of product standards . 3 4 Product dimensions . 3 Foreword This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carrie

11、d out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 4840-002:2017 (E) 3 1 Scope This standard lists the product standards and standard product dimensions, covered by technical specification EN 4840-001,

12、 for heat shrinkable moulded shapes. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the ref

13、erenced document (including any amendments) applies. EN 4840-001, Aerospace series Heat-shrinkable moulded shapes Part 001: Technical specification EN 4840-101, Aerospace series Heat shrinkable moulded shapes Part 101: Polyolefin, semi-rigid, limited fire hazard Temperature range 30 C to 105 C Produ

14、ct standard 1) EN 4840-102, Aerospace series Heat-shrinkable moulded shapes Part 102: Semi-rigid Temperature range 75 C to 120 C 2) EN 4840-103, Aerospace series Heat-shrinkable moulded shapes Part 103: Temperature range 55 C to 200 C 2) 3 List of product standards EN 4840-001, Aerospace series Heat

15、-shrinkable moulded shapes Part 001: Technical specification EN 4840-101, Aerospace series Heat shrinkable moulded shapes Part 101: Polyolefin, semi-rigid, limited fire hazard Temperature range 30 C to 105 C Product standard EN 4840-102, Aerospace series Heat-shrinkable moulded shapes Part 102: Semi

16、-rigid Temperature range 75 C to 120 C EN 4840-103, Aerospace series Heat-shrinkable moulded shapes Part 103: Temperature range 55 C to 200 C 4 Product dimensions See Tables 1 to 23. 1) Published as ASD-STAN Prestandard at the date of publication of this standard by AeroSpace and Defence industries

17、Association of Europe - Standardization (ASD-STAN) (www.asd-stan.org). 2) In preparation at the date of publication of this standard. prEN 4840-002:2017 (E) 4 Detail X Figure 1 Style AA (small lipped bottle) Table 1 Style AA Dimensions in millimetres Size code d1 d2 d3 l1 l2 l3 l4 s1 s2 s3 Mass g ma

18、x. max. min.a 10 % Ref. Ref. max. 20 % 20 % 30 % max.b 01 5,2 1,5 9 20 4 6,6 0,8 0,35 0,8 0,6 1,5 02 5,5 2 9 25 14 5 2 1 1 0,7 1.5 03 7 3 12 25 14 7,5 2 1 1,1 0.7 1,5 04 8 3,5 17 30 19 10 2 1 1,3 0,7 1,5 05 6,9 3,0 17 29 14 11 2 1 1,3 0,7 1,5 06 6,9 3,0 17 39 24 11 2 1 1,3 0,7 1,5 NOTE These parts m

19、ay be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details. a Shapes made from some material types may be supplied with a reduced d3 diameter. Refer to the individual manufacturer for exact dimensions. b The values of mass may be

20、higher for some material types. Refer to the individual manufacturer. prEN 4840-002:2017 (E) 5 Recovered As supplied Detail X As supplied (Size code 02 only) Figure 2 Style A (lipped short bottle with short body) Table 2 Style A Dimensions in millimetres Size code d1 d2 d3 l1 l2 l3 l4 s1 s2 s3 Mass

21、g max. max. min.a 10 % Ref. Ref. max. 20 % 20 % 30 % max.b 01 10,5 6,0 24,0 26,0 9,0 10,0 3,3 1,0 1,6 c 1,6 02 14,0 3,5 25,0 40,0 13,0 16,0 1,8 c 3,3 03 14,0 6,0 30,0 43,0 20,0 13,0 1,8 1,0 4,5 04 18,0 7,0 31,0 47,0 15,0 18,0 1,8 5,5 05 22,5 8,5 36,0 60,0 22,0 20,0 2,0 10,0 06 28,0 10,0 43,0 60.0 21

22、,0 20,0 1,7 2,2 12,7 07 35,0 16,0 60,0 90,0 32,0 38,0 1,7 3,2 1,5 29,5 08 45,0 17,0 66,0 130,0 50,0 50,0 2,0 4,0 2,0 71,5 09 58,0 27,0 82,0 130,0 37,0 55,0 2,0 4,0 4,0 100,0 NOTE These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manu

23、facturer for details. a Shapes made from some material types may be supplied with a reduced d3 diameter. Refer to the individual manufacturer for exact dimensions. b The values of mass may be higher for some material types. Refer to the individual manufacturer. c For these small shapes, this dimensi

24、on shall be between 0,35 mm and 1,0 mm. prEN 4840-002:2017 (E) 6 Recovered As supplied Detail X As Supplied (Size code 02 only) Figure 3 Style B (lipped straight bottle with medium body) Table 3 Style B Dimensions in millimetres Size code d1 d2 d3 l1 l2 l3 l4 l5 s1 s2 s3 Mass g max. max. min.a 10 %

25、Ref. Ref. max.b 10 % 20 % 20 % 30 % max.c 01 10,5 6,0 24,0 38,0 21,0 10,0 3,3 12,0 1,0 1,6 d 2,8 02 14,0 3,5 25,0 55,0 28,0 16,0 14,0 1,8 d 4,4 03 14,0 6,0 30,0 55,0 32,0 13,0 12,0 1,8 1,0 5,5 04 18,0 7,0 31,0 67,0 35,0 18,0 20,0 1,8 8,3 05 22,5 8,5 36,0 80,0 42,0 20,0 2,0 14,5 06 28,0 10,0 43,0 79,

26、0 41,0 20,0 1,7 2,2 18,0 07 35,0 16,0 60,0 110,0 52,0 38,0 1,7 3,2 1,5 41,0 08 45,0 17,0 66,0 150,0 70,0 50,0 2,0 4,0 2,0 87,0 09 58,0 27,0 82,0 158,0 58,0 55,0 2,0 4,0 4,0 121,0 NOTE These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual

27、 manufacturer for details. a Shapes made from some material types may be supplied with a reduced d3 diameter. Refer to the individual manufacturer for exact dimensions. b The innermost lip is optional. c The values of mass may be higher for some materials types. Refer to the individual manufacturer.

28、 d For these small shapes, this dimension shall be between 0,35 mm and 1,0 mm. prEN 4840-002:2017 (E) 7 Recovered As supplied Detail X Figure 4 Style C (lipped straight bottle with long body) Table 4 Style C Dimensions in millimetres Size code d1 d2 d3 l1 l2 l3 l4 l5b l6b s1 s2 s3 Mass g max. max. m

29、in.a 10 % Ref. Ref. max. 10 % 10 % 20 % 20 % 30 % max.c 06 28,0 10,0 43,0 79,0 41,0 20,0 3,3 20,0 20,0 1,7 2,2 1,0 24,5 07 35,0 16,0 60,0 110,0 52,0 38,0 1,7 3,2 1,5 50,0 08 45,0 17,0 66,0 150,0 70,0 50,0 2,0 3,8 2,0 103,0 09 58,0 27,0 82,0 178,0 58,0 55,0 37,0 2,0 4,0 4,0 184,0 NOTE These parts may

30、 be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details. a Shapes made from some material types may be supplied with a reduced d3 diameter. Refer to the individual manufacturer for exact dimensions. b The innermost lips are optio

31、nal. c The values of mass may be higher for some material types. Refer to the individual manufacturer. prEN 4840-002:2017 (E) 8 Recovered As supplied Figure 5 Style D (non-lipped straight bottle) Table 5 Style D Dimensions in millimetres Size code d1 d2 d3 l1 l2 l3 s1 Mass g max. max. min.a 10 % Ref

32、. Ref. 20 % max.b 01 8,0 3,8 16,0 25,4 14,2 6,0 1,3 1,2 02 10,5 5,6 23,0 38,1 22,0 9,5 1,5 3,3 03 14,5 6,6 28,0 52,5 27,0 15,0 1,8 4,3 04 18,0 7,5 31,0 66,0 37,0 18,0 1,8 7,7 05 24,5 8,6 36,0 73,7 42,0 17,0 1,8 13,6 06 28,5 9,9 42,0 97,0 58,0 21,0 2,0 21,7 07 35,5 16,0 51,0 127,0 65,0 41,0 3,2 54,5

33、08 44,5 20,3 66,0 160,5 91,0 48,0 3,8 105,0 09 57,5 27,0 81,0 210,0 115,0 61,5 4,2 199,0 NOTE These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details. a Shapes made from some material types may be supplied with a r

34、educed d3 diameter. Refer to the individual manufacturer for exact dimensions. b The values of mass may be higher for some material types. Refer to the individual manufacturer. prEN 4840-002:2017 (E) 9 Detail X Figure 6 Style E (lipped straight bottle with long tail) Table 6 Style E Dimensions in mi

35、llimetres Size code d1 d2 d3 d4 l1 l2 l3 l4 s1 s2 s3 Mass g max. max. min. min.a 10 % Ref. Ref. max. 20 % 20 % 30 % max.b 01 12,0 6,5 22,0 22,0 76,0 12,0 57,0 3,3 1,0 1,5 1,1 3,3 02c 13,0 2,0 19,0 6,0 60,0 38,0 4,1 03 15,0 7,5 25,5 25,5 83,0 60,0 4,4 04c 19,0 2,5 26,0 7,5 74,0 45,0 1,8 5,7 05 19,0 8

36、,5 29,0 29,0 89,0 63,0 6,5 06 23,0 10,0 34,0 34,0 102,0 73,0 8,0 07c 26,0 3,0 34,0 9,5 84,0 51,0 10,0 08 30,0 11,0 37,0 37,0 108,0 14,0 72,0 1,7 2,1 12,0 09c 34,0 3,5 43,5 11,5 100,0 12,0 58,0 1,8 10,0 10 34,0 12,0 43,5 43,5 114,0 15,0 74,0 2,0 14,0 11 41,0 14,5 50,0 50,0 118,0 15,0 73,0 2,3 1,4 22,

37、0 12 47,0 18,0 62,5 62,5 121,0 16,0 71,0 2 2,5 28,0 13 60,0 20,0 69,0 69,0 127,0 67,0 38,0 14 67,0 23,0 81,5 81,5 133,0 69,0 47,0 NOTE These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details. a Shapes made from som

38、e material types may be supplied with a reduced d3 diameter. Refer to the individual manufacturer for exact dimensions. b The values of mass may be higher for some material types. Refer to the manufacturer individual. c These sizes have a stepped “as supplied” profile ie d3 is larger than d4. prEN 4

39、840-002:2017 (E) 10 Recovered As supplied Detail X Figure 7 Style F (lipped right-angle boot) Table 7 Style F Dimensions in millimetres Size code d1 d2 d3 l1 l2 l3 l4 l5 s1 s2 s3 Mass g max. max. min.a 20 % Ref. Ref. max. Ref. 20 % 20 % 30 % max.b 01 10,5 6,0 24,0 32,0 25,0 19,0 3,3 10,0 1,0 1,3 0,6

40、 2,2 02 14,0 6,0 30,0 41,0 27,0 20,0 12,0 1,5 0,8 3,3 03 18,0 7,0 31,0 51,0 31,0 21,0 15,0 1,8 1,0 6,6 04 22,5 8,5 36,0 59,0 38,0 26,0 15,0 1,8 10,0 05 28,5 10,0 43,0 71,0 45,0 30,0 16,0 1,7 2,0 14,0 06 35,0 16,0 60,0 101,0 54,0 35,0 32,0 1,7 3,3 1,5 39,0 07 45,0 17,0 66,0 134,0 68,0 42,0 50,0 2,0 3

41、,8 2,0 71,0 08 61,0 25,0 82,0 152,0 84,0 52,0 39,0 2,0 4,0 4,0 165,0 09 8,0 3,5 17 25 20 15 2,0 7,5 1,0 1,3 0,7 2,0 NOTE These parts may be available with drain holes or with eyelets for connector protection caps. Refer to the individual manufacturer for details. a Shapes made from some material typ

42、es may be supplied with a reduced d3 diameter. Refer to the individual manufacturer for exact dimensions. b The values of mass may be higher for some materials. Refer to the individual manufacturer. prEN 4840-002:2017 (E) 11 Recovered As supplied Figure 8 Style G (non-lipped right-angle boot) Table

43、8 Style G Dimensions in millimetres Size code d1 d2 d3 l1 l2 l3 l4 s1 Mass g max. max. min.a Ref. 10 % Ref. Ref. 20 % max.b 01 7,9 3,8 16,5 17,3 20,1 15,2 4,3 1,0 1,2 02 10,4 5,6 23,6 21,3 22,9 16,5 5,8 1,3 1,7 03 14,2 6,3 28,4 26,9 26,7 18,5 7,1 1,5 3,4 04 17,8 7,1 31,5 36,6 30,5 20,6 10,2 1,8 7,7

44、05 22,4 8,4 36,0 43,7 35,1 22,9 12,7 1,8 10,4 06 27,9 9,7 43,1 53,6 43,9 29,2 17,3 2,0 15,8 07 35,1 15,7 52,3 75,7 52,9 34,0 32 3,3 42 08 44,5 20,3 66,0 97,5 66,0 42,2 40,6 3,8 77,9 09 57,2 26,7 81,2 128 79,2 49 56,4 4,6 168,7 10 44,5 20,3 76,2 97,5 66,0 41,7 40,6 3,8 72,2 NOTE These parts may be av

45、ailable with drain holes. Refer to the individual manufacturer for details. a Shapes made from some material types may be supplied with a reduced d3 diameter. Refer to the individual manufacturer for exact dimensions. b The values of mass may be higher for some materials. Refer to the individual man

46、ufacturer. prEN 4840-002:2017 (E) 12 Recovered As supplied Detail X Figure 9 Style H (lipped right-angle boot with long tail) Table 9 Style H Dimensions in millimetres Size code d1 d2 d3 d4 l1 l2 l3 l4 l5 s1 s2 s3 Mass g max. max. min. min.a 10 % 10 % Ref. max. Ref. 20 % 20 % 30 % max.b 01 12,0 6,5

47、22,0 22,0 70,0 19,0 14,0 3,3 52,0 1,0 1,5 1,1 3,3 02c 13,0 2,0 19,0 6,0 45,0 16,0 14,0 22,0 3,8 03 15,0 7,5 25,5 25,5 79,0 20,0 15,0 54,0 5,0 04c 19,0 2,5 26,0 7,5 67,0 18,0 29,0 1,8 5,7 05 19,0 8,5 29,0 29,0 89,0 21,0 57,0 6,6 06 23,0 10,0 34,0 34,0 102,0 22,0 62,0 9,0 07c 26,0 3,0 34,0 9,5 81,0 19

48、,0 16,0 35,5 7,0 08 30,0 11,0 37,0 37,0 108,0 24,0 17,0 67,0 1,7 2,0 13,0 09c 34,0 3,5 43,5 11,5 116,0 21,0 18,0 47,0 1,8 10,0 10 34,0 12,0 43,5 43,5 121,0 27,0 19,0 76,0 2,0 15,0 11 41,5 14,5 50,0 50,0 132,0 30,0 20,0 81,0 2,3 1,4 24,0 12 47,0 18,0 62,5 62,5 133,0 33,0 22,0 74,0 2,0 2,5 30,0 13 60,

49、0 20,0 69,0 69,0 137,0 35,0 23,0 61,0 39,0 14 67,0 23,0 82,0 82,0 140,0 45,0 31,0 54,0 53,0 NOTE These parts may be available with drain holes. Refer to the individual manufacturer for details. a Shapes made from some material types may be supplied with a reduced d4 diameter. Refer to the individual manufacturer for exact d