ImageVerifierCode 换一换
格式:PDF , 页数:8 ,大小:319.26KB ,
资源ID:453619      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-453619.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASD-STAN PREN 6035-1995 Aerospace Series Fibre Reinforced Plastics Test Method Determination of Notched and Unnotched Tensile Strength (Edition P1)《航空航天系列 纤维增强塑料的试验方法 切口和非切口抗拉强度的测定.pdf)为本站会员(amazingpat195)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASD-STAN PREN 6035-1995 Aerospace Series Fibre Reinforced Plastics Test Method Determination of Notched and Unnotched Tensile Strength (Edition P1)《航空航天系列 纤维增强塑料的试验方法 切口和非切口抗拉强度的测定.pdf

1、AECMA PRENlkb035 95 LOL2311 O009993 5TT = Edition approved for publication AECMA STANDARD NORME AECMA AECMA NORM AIBITFG Chairman Comments should be sent within six months after the date of publication to prEN 6035 Edition PI November 1995 - PUBLISHED BY THE EUROPEAN ASSOCIATION OF AEROSPACE INDUSTR

2、IES (AECMA) Gulledelle 94 - 8-1200 BRUXELLES - Tel. (32) 2 775 81 10 - Fax. (32) 2 775 81 11 ICs : Descriptors : ENGLISH VERSION Aerospace series Fibre reinforced plastics Test method Determination of notched and unnotched tensile strength Srie arospatiale Matires plastiques renforces de fibres Mtho

3、de dessai Dtermination de la rsistance en traction lisse et en traction troue Luft- und Raumfahrt Faserverstrkte Kunststoffe Prfverfahren Bestimmung der Kerbzugfestigkeit an gekerbten und ungekerbten Probekrpern This “Aerospace Series“ Prestandard has been drawn up under the responsibility of AECMA

4、(The European Association of Aerospace Industries). It is published on green paper for the needs of AECMA-Members. It has been technically approved by the experts of the concerned Technical Committee following comment by the Member countries. Subsequent to the publication of this Prestandard, the te

5、chnical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and signature of the AECMA Standard Checking Centre (NPSI and formal agreement of the Officiai Services of the Member countr

6、ies it will be submitted as a draft European Standard to CEN (European Committee for Standardization) for formal vote. 1995-1 1-30 AECMA Gulledelle 94 6-1 200 BRUXELLES Mr K. Schneider I aecma 1995 - AECMA PREN*b035 95 = LOL23LL O009994 436 Page 2 prEN 6035 : 1995 Contents list 1 2 3 4 5 6 7 8 9 10

7、Scope Normative references Definitions Principie of the method Designation of the method Apparatus Test specimen Procedure Presentation of the results Test report AECMA PRENxb035 75 m LOL23LL 0009995 372 Page 3 prEN 6035 : 1995 1 Scope This standard defines a method to be used to determine the tensi

8、le strength of notched and unnotched fibre reinforced plastics. It is applicable to composite laminates with unidirectional plies or woven fabrics reinforcement. This standard does not give any direction necessary to meet health and safety requirements. It is the responsibility of the user of this s

9、tandard to consult and establish appropriate health and safety precautions. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications ar

10、e listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies. EN 2374 Aerospace ser

11、ies Glass fibre reinforced mouldings and sandwich Production of test panels EN 2489 EN 2565 EN 2743 EN 2823 Aerospace series Fibre reinforced plastics Determination of the action of liquid chemicals 1) Aerospace series Preparation of carbon fibre reinforced resin panels for test purpose 1) Aerospace

12、 series Fibre reinforced plastics Standard atmospheres for conditioning and testing Aerospace series Fibre reinforced plastics Test method for the determination of the effect of exposure to humid atmosphere on physical and mechanical characteristics ?I 3 Definitions 3.1 Unnotched tensile strength Ma

13、ximum tensile load experienced by the unnotched test specimen divided by the initial cross sectional area within the gauge length. 3.2 Notched tensile strength Maximum tensile load experienced by the notched test specimen divided by the initial gross cross sectional area within the gauge length. 1)

14、Published as AECMA Prestandard at the date of publication of this standard. AECMA PRENab035 95 = LOL23Ll OOOb 209 Page 4 prEN 6035 : 1995 3.3 KT value Unnotched tensile strength divided by the notched tensile strength. 4 Principle of the method A tensile test on unnotched specimen is carried out in

15、order to determine the original material strength. A test is performed on notched specimen to determine the residual strength. 5 Designation of the method The designation of the method shall be in accordance with the following example. Description block Identity block Determination of notched and un

16、notched Fibre reinforced plastics tensile strength Number of this standard Laminate configuration A (see table 1) 6 Apparatus 6.1 Calibrated tensile test machine accurate to within loh, equipped with facilities to record maximum load. 6.2 Chamber adapted to the machine to carry out tests at temperat

17、ure. The temperature shall be maintained within f 3C. 6.3 Timer. 6.4 6.5 Thermocouple with recorder to monitor temperature for tests at other than ambient. Flat faced micrometer with 6 mm diameter faces, accurate to 0,Ol mm 6.6 Vernier calliper accurate to the nearest 0,l mm. 7 Test specimen 7.1 Spe

18、cimen description For the description, dimensions and tolerances see figure 1 for notched type specimen and figure 2 for unnotched type specimen. The laminate configurations for the fibre directions are defined in table 1. 7.2 Test specimen preparation The specimens are cut out from laminates. The c

19、oefficient of variation in the thickness measurements shall be smaller than 2% per laminate. The laminates shall be produced according to EN 2565 for carbon and EN 2374 for glass. Special precautions have to be taken to ensure that no delamination occurs during machining especially for the drilling

20、of the notched specimens. The laminate should be inspected for example by C-Scan to establish that the laminate is worth testing. If the NDT reveals unacceptable defects,limits defined in the specification invoking the test, the laminate should not be tested. The process parameters shall be in line

21、with the specification invoking the test. AECMA PREN*b035 95 LOL231L O009997 I45 D Page 5 prEN 6035 : 1995 7.3 Tabs The tests may be performed without the specimen being tabbed. However, if tabs are used they shall be strain compatible with the composite being tested either, by using precured tabs o

22、f two plies of fabric, lay-up + and - 45“, or by co-bonding using a suitable prepreg system. The precured tabs shall be bonded on both specimens faces with a suitable adhesive system. Care should be taken that the adhesive bonding temperature does not add any undesired post cure effect to the lamina

23、te. 7.4 Number of specimens Five specimens shall be tested per test condition, except when otherwise specified in the technical specif ication. If tests are carried out after ageing or at a temperature different from room temperature, care should be taken to assure that room temperature/dry referenc

24、e specimens, which had been machined from the same plate as the specimens under investigation are also tested. 7.5 Ageing In case of tests after immersion, the conditions shall be according to EN 2489. For tests after exposure to humid atmosphere, the conditioning shall be in accordance with EN 2823

25、. 8 Procedure 8.1 Conditioning The storage and testing of as received specimens shall be carried out at (23 k 2) OC, (50 f 5) Yo relative humidity in accordance with EN 2743. Aged specimens shall be tested within a maximum of 8 hours after removal from the exposure environment. 8.2 Determination of

26、dimensions Measure and record the thickness and width at three points in the gauge length of the specimen before ageing and again before mechanical testing. Use the micrometer (see 6.5) for the thickness and the vernier calliper (see 6.6) for the width. Average the three measurements. 8.3 Test at am

27、bient temperature Place the specimen in the jaws, ensuring that it is aligned within 1“ and centred on the machine axis. (Note: The jaws shall fully cover the tabs if used). Select the load range such that failure occurs between 20 o/o and 80 % of full scale. Tensile load shall be applied at a const

28、ant cross head speed of 2 mmmin. Record the maximum load Pr 8.4 Test at temperature other than ambient Apply a thermocouple (see6.4) on the composite material as close as possible to the centre of the specimen and seal the thermocouple from the surrounding air by using vacuum bag sealant. After a dr

29、y specimen has reached a ternpararture of 2C below the required elevated temperature or 2C above the required sub-zero temperature, the specimen shall be maintained at the required condition for five minutes prior to testing. The above time for aged specimen is 1 minute The heat up/soak cycle used s

30、hall be given in the test report. For specimens that have been subjected to fluid immersion, apply EN 2489. For specimens that have undergone humidity ageing, apply EN 2823. Follow the same procedure as for the test at ambient temperature. AECIA PRENmb035 95 W LOL23LL 0009998 081 Page 6 prEN 6035 :

31、1995 9 Presentation of the results 9.1 Tensile strength ot For notched specimens Pr otn = For unnotched specimens otu = txw Pr where : otn, otu are the tensile strengths for, notched and unnotched specimens, in MPa is the maximum load, in Newton is the specimen width, in millimetres is the thickness

32、 of the specimen, in millimetres Pr W t 9.2 Nominal tensile strength ont For notched specimens For unnotched specimens ontu = where Pr tnxw Pr tn x w ontn ontu Pr W is the specimen width, in millimetres tn are the nominal tensile strength for, notched and unnotchedspecimens, in MPa is the maximum lo

33、ad, in Newton is the nominal thickness of the specimen, in millimetres, as specified in the relevant material specification 9.3 KT value (see 3.3) AECMA PREN*b035 95 m LOL23LL 0009999 TLB m Tapes Page 7 prEN 6035 : 1995 Fibre mass per unit area Quasi-isotropic laminates Directed laminates (!Ym2 1 Ty

34、pe A Type B 130 -145 160 -190 260 -290 ( 45, O, -45,90 ) 4 sym ( 45, O , -45,90 ) 3 sym ( 45, O, -45,90 ) 2 sym ( O ,45 , -45, O ,90 ) 3 sym ( O ,45 , -45 , O ,90 ) 2 sym ( O ,45, -45, O ,90 ) 2 sym 10 Test report The test report shall refer to this standard and shall include the following. 10.1 10.

35、2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 Complete identification of the material tested, including at least type, source, manufacturers code number, fibre areal weight, filament count, processing details. All details regarding specimen preparation (including when applicable : tabs material, tabs adhesiv

36、e and curing condition of this adhesive) The measured specimen dimensions. Ageing and/or exposure conditions prior to the test. Date of test, facility and identification of individuals performing the test. Equipment, method and test parameters used. Individual values, mean value and standard deviati

37、on of tensile strength for notched and unnotched specimen. KT value Any incident which may have affected the results and any deviation from this standard. di Table 1 : Laminate configurations Lay-ups for different fibre mass per unit area Directed and quasi-isotropic laminates 1) 2) O“ is equivalent

38、 to warp direction and 90“ is equivalent to weft direction n to be determined to have a laminate thickness as close as possible to 4 mm AECMA PRENmb035 95 L0123iIiI OOiIOOOO 123 Page 8 prEN 6035 : 1995 I I - 180 0,5 - Dimensions in rnm L=21 +180mm 1 = tab length : Function of the equipment (test mac

39、hine, jaws, etc) and / or the material to be t : according to lay-up (see table 1) tested (tabs must be able to transfer the shear loads). Figure 1 : Notched tensile specimen R = 200 f 1 /- Il 0,05 f 7 * f I Dimensions in mm L=21 +180mm 1 = tab length : Function of the equipment (test machine, jaws,

40、 etc) and / or the material to be t : according to lay-up (see table 1) tested (tabs must be able to transfer the shear loads). Figure 2 : Unnotched tensile specimen Note: Parallelism of tab faces must be maintained to within 0,05 mrn across width and length. Tabs faces must be parallel with specimen faces to within 0,05mm.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1