ASD-STAN PREN 6049-005-2005 Aerospace series Electrical cables installation Protection sleeve in meta-aramid fibres Part 005 Sleeve flexible post installation Product standard (Edi.pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 6049-005 Edition P2 November 2005 PUBLISHED BY THE AEROSPACE AND DEFENSE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONGulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Supersedes Edition P1 September 1997 De

2、scriptors: ENGLISH VERSION Aerospace series Electrical cables, installation Protection sleeve in meta-aramid fibres Part 005: Sleeve flexible, post installation Product standard Srie arospatiale Cbles lectriques, installation Gaine de protection en fibres mta-aramides Partie 005 : Gaine de protectio

3、n souple installer au montage Norme de produit Luft- und Raumfahrt Elektrische Leitungen, Installation Schutzschluche aus Meta-Aramidfasern Teil 005: Biegsame Schutzschluche Nachtrglicher Einbau Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (T

4、he Aerospace and Defense Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the te

5、chnical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (Europ

6、ean Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition

7、 approved for publication 30 November 2005 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2005 by ASD-STAN prEN 6049-005:20052 Contents Page 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Requirements.3 4.1 Composition

8、 and mass .3 4.1.1 Composition of the tows.3 4.1.2 Composition, dimensions and mass of the sleeve 3 4.2 Colour and materials .4 4.2.1 Colour .4 4.2.2 Materials .5 4.3 Mechanical properties.5 4.3.1 Temperature range 5 4.3.2 Sun light exposure 5 4.3.3 Bending properties5 4.3.4 Locking of the closing s

9、ystem .5 4.3.5 Resistance to fluids.5 4.3.6 Water absorption .5 4.3.7 Mould growth .5 4.3.8 Tensile strength of tows .5 5 Test methods5 6 Designation 6 7 Marking .6 8 Technical specification .6 prEN 6049-005:2005 3 1 Scope This standard defines the characteristics of post installation flexible mecha

10、nical protection sleeves for electrical cable and cable bundles made from meta-aramid fibres and provided with a water repelled protection. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited a

11、pplies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 6049-001, Aerospace series Electrical cables, installation Protection sleeve in meta-aramid fibres Part 001: Technical specification. 1)EN 6059-*, Aerospace series Electrical cables,

12、installation protection sleeve Test methods. 1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 6049-001 and the following apply. 4 Requirements 4.1 Composition and mass 4.1.1 Composition of the tows Each tow shall be built-up of groups of multifilamen

13、t fibres made from meta-aramid. The number of groups which forms a tow and the width of the tow depends on the braiding configuration (braiding figure and braiding angle) of the sleeve, see 4.1.2. The thickness of the tow shall be so that the finished sleeve meet the mechanical and environmental req

14、uirements. One length of sleeve shall be built-up of one type of tow. 4.1.2 Composition, dimensions and mass of the sleeve The weaving of tows and the closing mechanism shall applied so that the sleeves meet the requirements for dimensions, coverage and mass. The closing system shall be a hook and l

15、oop system. The weaving pattern of the tows shall be in such a way that the coverage is minimum 90 % for all sizes. Figure 1 and Table 1 give the composition and the dimensions of the sleeve. *All its parts quoted in this standard. 1) Published as AECMA Prestandard as the date of publication of this

16、 standard. prEN 6049-005:20054 Key 1 Closing strip (loop side) 2 Closing strip (hook side) aDelivery length Figure 1 Composition of post installation sleeve Table 1 Dimensions, tolerances and mass Dimensions in millimetres Size code Inner diameter d Width of closing strip a Developed width b Mass ma

17、x. Nominal g/m 10 10 45 4 32 15 15 60 8 36 20 20 13 2 75 7 43 25 25 105 10 70 30 30 25 1 120 12 77 4.2 Colour and materials 4.2.1 Colour Colour shall be olive green, code 5. La2 1 bd a prEN 6049-005:2005 5 4.2.2 Materials The materials shall be multifilament fibres of meta-aramid and meet the requir

18、ements as specified in this standard. The closing mechanism shall be a suitable material which fulfil the requirements of this specification. 4.3 Mechanical properties 4.3.1 Temperature range The operation temperature of the protection sleeves shall be: Maximum: 175 C, Minimum: 55 C. 4.3.2 Sun light

19、 exposure After testing according to EN 6059-301 for 40 hours, the retention of the tensile strength shall be 45 % minimum with respect to the determined values of non-tested tows. 4.3.3 Bending properties Bending of the minimum radius of five times of the nominal diameter as specified in EN 6059-40

20、2, shall be possible under the conditions mentioned in 4.3.4. 4.3.4 Locking of the closing system The locking of the closing system shall be so that opening and closing is possible by hand. If closed around a cable bundle which is 80 % of the nominal inner diameter of the sleeve, the mechanism shall

21、 be in a closed position. 4.3.5 Resistance to fluids After testing according to EN 6059-303, the locking mechanism shall not be damaged and the retention of the tensile strength shall be 90 % minimum with respect to the determined values of non-tested tows. 4.3.6 Water absorption To fulfil the requi

22、rements for water absorption, the sleeve shall repel water as tested in EN 6059-305 for six hours. This test shall be executed after a high temperature exposure test according to EN 6059-302. 4.3.7 Mould growth After tested in accordance with EN 6059-306, there shall no external deterioration which

23、would affect service use and no mould growth visible to the naked eye. 4.3.8 Tensile strength of tows The tensile force to be applied per dTEX shall not be less than 0,03 N. Degradation of the tensile strength after environmental tests shall be within the limits as mentioned in the relevant paragrap

24、h. For this test, unbraided tows of the batch which have been used for braiding of the sleeves may be used. 5 Test methods The tests shall be carried out as shown in Table 2. For the number of samples to be tested, see EN 6049-001. prEN 6049-005:20056 Table 2 Test methods and details EN 6059- Design

25、ation of the test Details 201 Visual inspection See 4.1 and 4.2.1. 202 Dimensions and mass See 4.1.2. 203 Coverage See 4.1.2. 301 Sun light exposure See 4.3.2. 302 High temperature exposure At 175 C 303 Resistance to fluids See 4.3.5. 304 Flammability 305 Fluid absorption See 4.3.6. 306 Mould growth

26、 See 4.3.7. 401 Expansion range Not applicable 402 Bending properties See 4.3.3. 403 Scrape abrasion Needle load shall be 10 N. 404 Tensile strength See 4.3.8. 405 Dynamic cut-through Load shall be 30 N. 601 Smoke density 602 Toxicity 6 Designation EXAMPLE Description block SLEEVE, OPENABLE FLEXIBLE Identity block EN6049005205 Number of this standard Size code (see Table 1) Colour code (see 4.2.1) 7 Marking For the marking of the packaging, see EN 6049-001. 8 Technical specification EN 6049-001.