ASD-STAN PREN 6093-2006 Aerospace series Receptacle floating single lug (Edition P 1).pdf

1、ASD STANDARD NORME ASD ASD NORM prEN 6093 Edition P 1 July 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATIONGulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Descriptors: ENGLISH VERSION Aerospace series

2、Receptacle, floating, single lug Srie arospatiale Rceptacle, flottant, simple patte Luft- und Raumfahrt Haltenocken, schwimmend, einseitig This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The AeroSpace and Defence Industries Association of Europe - Standard

3、ization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the technical content shall not be changed to an extent that interchangeab

4、ility is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European Committee for Standardization) for formal vote and transformatio

5、n to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition approved for publication 31 July 2006 Comments should be sent withi

6、n six months after the date of publication to ASD-STAN Mechanical Domain Copyright 2006 by ASD-STAN prEN 6093:20062 Contents Page Foreword2 1 Scope 3 2 Normative references 3 3 Requirements.4 4 Designation 7 5 Marking .7 6 Technical specification .8 7 Example of installation8 Bibliography9 Foreword

7、This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Mechanical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. prEN 6093:2006 3 1 Scope Thi

8、s standard specifies the dimensions, tolerances, required characteristics and mass of a receptacle for use in fuselage interior equipment and structural applications. This standard shall be used in conjunction with studs per EN 6088 or EN 6105. 2 Normative references The following referenced documen

9、ts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 2768-1, General tolerances Part 1: Tolerances for linear and angular dimensio

10、ns without individual tolerance indications. ISO 8080, Aerospace Anodic treatment of titanium and titanium alloys Sulfuric acid process. EN 2424, Aerospace series Marking of aerospace products. EN 2516, Aerospace series Passivation of corrosion resistant steels and decontamination of nickel base all

11、oys. EN 2808, Aerospace series Anodizing of titanium and titanium alloys. EN 6088, Aerospace series Stud. 1)EN 6089, Aerospace series Washer, retaining.2)EN 6090, Aerospace series Washer, retaining.2)EN 6091, Aerospace series Circlip. 2)EN 6094, Aerospace series Washer, spring, countersunk. 2)EN 609

12、5, Aerospace series Rotary fasteners, structural and non-structural applications, technical specification. 1)EN 6105, Aerospace series Stud, recessed. 1)EN 10088-3, Stainless steels Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of co

13、rrosion resisting steels for general purposes. EN 10270-1, Steel wire for mechanical springs Part 1: Patented cold drawn unalloyed spring steel wire. EN 10270-3, Steel wire for mechanical springs Part 3: Stainless spring steel wire. DIN 17850, Titanium, chemical composition. AMS 2700, Passivation of

14、 corrosion resistant steels. 3)1) In preparation at the date of publication of this standard. 2) Published as ASD Prestandard at the date of publication of this standard. 3) Published by: Society of Automotive Engineers (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA. prEN 6093:20064 A

15、MS 5528, Steel, corrosion resistant, sheet, strip and plate, 17Cr-7.1Ni-1.1Al, solution heat treated, precipitation hardenable. 3)AS 8879, Screw threads, UNJ profile, inch controlled radius root with increased minor diameter. 3)MIL-DTL-83488, Coating, aluminium, high purity. 4)MIL-PRF-46010, Lubrica

16、nt, solid film, heat cured, corrosion inhibiting. 4)3 Requirements 3.1 Configuration, dimensions and tolerances The configuration, dimensions and tolerances shall conform with Figure 1. Dimensions and tolerances are expressed in millimetres. Tolerances not specified shall be in accordance with ISO 2

17、768-1 (Tolerance class: ISO 2768-m). All dimensions and tolerances apply after surface treatment. All burrs to be removed/sharp edges to be broken. 4) Published by: Department of Defense (DoD), the Pentagon, Washington, D.C., 20307, USA. prEN 6093:20065 YZ3,00,30,6 0,30,2 0,30,6 0,1515,0 maxZ0,6410,

18、5 max14,5 max13,6Thread perAS88798-32UNC-3A2 leadScrewPlateSpringsWashersCap10,0 0,115,25 0,1 6,352,500,111,20Marking seeclause 5AAA-AYR30,9 0,1Key 1 Washers 2 Cap 3 Springs 4 Thread per AS 8879, 8-32UNC-3A, 2 lead 5 Plate 6 Screw 7 Marking, see Clause 5 Figure 1 Configuration, dimensions and tolera

19、nces 7 1 3 654 2 prEN 6093:20066 3.2 Material and surface treatment See Table 1. Table 1 Material and surface treatment Dash number Finish code Element Material Finish Lubricant Screw Corrosion resistant steel 1.4303 per EN 10088-3 Dry film per MIL-PRF-46010 aCap Corrosion resistant steel 1.4404 per

20、 EN 10088-3 bPlate Corrosion resistant steel per AMS 5528 Springs Corrosion resistant steel 1.4310 per EN 10270-1 or EN 10270-3 None 01 Washers Corrosion resistant steel per AMS 5528 Passivated per AMS 2700 or EN 2516 Dry film per MIL-PRF-46010 Screw Corrosion resistant steel 1.4303 per EN 10088-3 D

21、ry film per MIL-PRF-46010 aCap Corrosion resistant steel 1.4404 per EN 10088-3 bPlate Corrosion resistant steel per AMS 5528 IVD coating per MIL-DTL-83488 type II, class 3 Springs Corrosion resistant steel 1.4310 per EN 10270-1 or EN 10270-3 None 01 V Washers Corrosion resistant steel per AMS 5528 D

22、ry film per MIL-PRF-46010 Screw Corrosion resistant steel 1.4303 per EN 10088-3 Passivated per AMS 2700 or EN 2516 Dry film per MIL-PRF-46010 aCap Titanium alloy 3.7035 per DIN 17850 Anodized per EN 2808 or ISO 8080 Plate Corrosion resistant steel per AMS 5528 Springs Corrosion resistant steel 1.431

23、0 per EN 10270-1 or EN 10270-3 None 02 S Washers Corrosion resistant steel per AMS 5528 Passivated per AMS 2700 or EN 2516 Dry film per MIL-PRF-46010 aAt manufacturers discretion bCarbon content of 0,3 % max. permitted after sintering process prEN 6093:2006 7 3.3 Mass See Table 2. Table 2 Mass Dash

24、number Finish code Mass (Ref.) kg/1 000 pieces 01 6,7 01 V 6,7 02 S 5,2 3.4 Floatability Minimum floatability: 0,64 mm radially from center 3.5 Static values Maximum axial tensile load: 6 000N Locking torque: 2,8 Nm 3,2 Nm 3.6 Operating temperature This receptacle shall be used in the temperature ra

25、nge of 55 C to 150 C. 4 Designation EXAMPLE Description block RECEPTACLE Identity block EN6093-01V Number of this standard Dash number (see Tables 1 and 2) Material and finish code (see Tables 1 and 2) NOTE If necessary, the code I9005 shall be placed between the description block and the identity b

26、lock. 5 Marking EN 2424, style F prEN 6093:20068 6 Technical specification EN 6095 7 Example of installation RECEPTACLE per EN6092WASHER per EN6094STUD per EN6088 or EN6105Key 1 Washer per EN 6094 2 Receptacle per EN 6093 3 Stud per EN 6088 or EN 6105 NOTE Retaining washer EN 6090 or retaining washe

27、r EN 6089 and circlip EN 6091 respectively not shown. Refer to relevant standard for details of installation. Figure 2 Example of installation 13 2 prEN 6093:20069 Bibliography 1 EN 6092, Aerospace series Receptacle, floating, double lug. 2)2 EN 10263-5, Steel rod, bars and wire for cold heading and cold extrusion Part 5: Technical delivery conditions for stainless steels.