ASD-STAN TR 4831-2014 Aerospace series Applicable crimping tools for electrical contact product standards EN 3155-065 and EN 3155-083 (Edition 1).pdf

1、ASD-STAN Technical Report Rapport Technique ASD-S TAN ASD-STAN Fachbericht TR 4831 Edition 1 April 2014 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Rue Montoyer 10 - 1000 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 775 8131 - www.asd-stan.orgICS: Descr

2、iptors: ENGLISH VERSION Aerospace series Applicable crimping tools for electrical contact product standards EN 3155-065 and EN 3155-083 Srie arospatiale Outil de sertissage applicable pour les normes de produits EN 3155-065 et EN 3155-083 Luft- und Raumfahrt Anzuwendende Crimpwerkzeuge fr elektrisch

3、e Kontakte der Produktnormen EN 3155-065 und EN 3155-083 This Technical Report was drawn up by the Electrical Domain of ASD-STAN. The reason which led to the publication of the document as a Technical Report is explained in the foreword. Edition approved for publication 1stApril 2014 Electrical Doma

4、in Copyright 2014 by ASD-STAN Page 2 TR 4831:04-2014 Contents Page Foreword 3 0 Introduction 4 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Required characteristics .5 Annex 1 (informative) Locator definition for M22520/23-01 6 Page 3 TR 4831:04-2014 Foreword The main task of ASD-

5、STAN Domains is to prepare EN standards. In exceptional circumstances, however, the publication of a Technical Report of one of the following types may be proposed: type 1, the subject is still under technical development requiring wider exposure; type 2, a Domain has collected data of a different k

6、ind from that which is normally published as a European Standard. The Standardization Committee ASD-STAN decided to publish this document in the form of a Technical Report of type 2 in order to facilitate the updating of this document. Page 4 TR 4831:04-2014 0 Introduction The aim of this technical

7、report is to provide and specify the applicable tools for crimping the product standard EN 3155-065 and EN 3155-083 until to obtain standardization and publication of the appropriate tool product standards EN 4008. 1 Scope This standard specifies necessary characteristics for: The die set and the lo

8、cator used with the pneumatic tool reference MIL-C-22520/23-01, The locator and the selector used with manual tool reference M300BT. to crimp the electrical contact EN 3155-065 and EN 3155-083. 2 Normative references The following documents, in whole or in part, are normatively referenced in this do

9、cument and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2083, Aerospace series Copper or copper alloy conductors for electrical cables Product

10、standard EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3155-001, Aerospace series Electrical contacts used in elements of connection Part 001: Technical specification EN 3155-065, Aerospace series Electrical contacts used in elements of

11、 connection Part 065: Contacts, electrical, male, type A, crimp, class S, size 8 Product standard EN 3155-083, Aerospace series Electrical contacts used in elements of connection Part 083: Contacts, electrical, female, type A, crimp, class S, size 8 Product standard 1)EN 4008 (all parts), Aerospace

12、series Elements of electrical and optical connection Crimping tools and associated accessories EN 4434, Aerospace series Copper or copper alloy lightweight conductors for electrical cables Product standard (Normal and tight tolerances) MIL-C 22520/23, Crimping tools, terminal, hand or power actuated

13、, wire termination, pneumatic tool for wire barrel sizes 0000 through 8 2)MIL-DTL-22520G, Crimping tools, wire termination, general specification for 2)1) Published as ASD-STAN Prestandard at the date of publication of this standard (www.asd-stan.org) 2) Published by: DoD National (US) Mil. Departme

14、nt of Defense http:/www.defenselink.mil/ Page 5 TR 4831:04-2014 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics The selector number used for crimping copper or copper alloy conductors in cables EN 2083 and EN

15、 4434 are indicated in Table 1. It is the responsibility of the user if the parameters in Table 1 are changed for service use. Table 1 Contact Contact Cable size M22520/23-01 (Pneumatic Tool) M300BT (Manual Tool) Product standard Contactsize Barrel size ASD code AWG a Die set Locator Locator Selecto

16、rEN 3155-065 and EN 3155-083 08 08 090 8 M22520/23-02 See Annex 1 (informative) SP593 4 08 10 051 or 050 10 WA23-101DA See Annex 1 (informative) SP593 3 aAWG Closest American Wire Gauge. Page 6 TR 4831:04-2014 Annex 1 (informative) Locator definition for M22520/23-01 Material: Aluminium alloy Plating: None Figure A.1 Detail A-A