ASME A112 19 1-2013 Enamelled cast iron and enamelled steel plumbing fixtures《搪瓷铸铁和搪瓷钢管子附件》.pdf

1、ASME A112.19.1-2013/CSA B45.2-13Enamelled cast iron and enamelled steel plumbing fixturesLegal Notice for Harmonized StandardJointly Developed by ASME and CSA GroupIntellectual property rights and ownershipAs between American Society of Mechanical Engineers (ASME) and Canadian Standards Association

2、(Operating as “CSA Group) (collectively ASME and CSA Group) and the users of this document (whether it be in printed or electronic form), ASME and CSA Group are the joint owners of all works contained herein that are protected by copyright, all trade-marks (except as otherwise noted to the contrary)

3、, and all inventions and trade secrets that may be contained in this document, whether or not such inventions and trade secrets are protected by patents and applications for patents. The unauthorized use, modification, copying, or disclosure of this document may violate laws that protect the intelle

4、ctual property of ASME and CSA Group and may give rise to a right in ASME and CSA Group to seek legal redress for such use, modification, copying, or disclosure. ASME and CSA Group reserve all intellectual property rights in this document.Disclaimer and exclusion of liabilityThis document is provide

5、d without any representations, warranties, or conditions of any kind, express or implied, including, without limitation, implied warranties or conditions concerning this documents fitness for a particular purpose or use, its merchantability, or its non-infringement of any third partys intellectual p

6、roperty rights. ASME and CSA Group do not warrant the accuracy, completeness, or currency of any of the information published in this document. ASME and CSA Group make no representations or warranties regarding this documents compliance with any applicable statute, rule, or regulation.IN NO EVENT SH

7、ALL ASME AND CSA GROUP, THEIR RESPECTIVE VOLUNTEERS, MEMBERS, SUBSIDIARIES, OR AFFILIATED COMPANIES, OR THEIR EMPLOYEES, DIRECTORS, OR OFFICERS, BE LIABLE FOR ANY DIRECT, INDIRECT, OR INCIDENTAL DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES, HOWSOEVER CAUSED, INCLUDING BUT NOT LIMITED TO SPECIAL OR CONS

8、EQUENTIAL DAMAGES, LOST REVENUE, BUSINESS INTERRUPTION, LOST OR DAMAGED DATA, OR ANY OTHER COMMERCIAL OR ECONOMIC LOSS, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR ANY OTHER THEORY OF LIABILITY, ARISING OUT OF OR RESULTING FROM ACCESS TO OR POSSESSION OR USE OF THIS DOCUMENT, EVEN IF

9、ASME OR CSA GROUP HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, INJURY, LOSS, COSTS, OR EXPENSES.In publishing and making this document available, ASME and CSA Group are not undertaking to render professional or other services for or on behalf of any person or entity or to perform any duty o

10、wed by any person or entity to another person or entity. The information in this document is directed to those who have the appropriate degree of experience to use and apply its contents, and ASME and CSA Group accept no responsibility whatsoever arising in any way from any and all use of or relianc

11、e on the information contained in this document. ASME and CSA Group have no power, nor do they undertake, to enforce compliance with the contents of the standards or other documents they jointly publish. Authorized use of this documentThis document is being provided by ASME and CSA Group for informa

12、tional and non-commercial use only. The user of this document is authorized to do only the following:If this document is in electronic form:. load this document onto a computer for the sole purpose of reviewing it;. search and browse this document; and. print this document if it is in PDF format.Lim

13、ited copies of this document in print or paper form may be distributed only to persons who are authorized by ASME and CSA Group to have such copies, and only if this Legal Notice appears on each such copy.In addition, users may not and may not permit others to. alter this document in any way or remo

14、ve this Legal Notice from the attached standard;. sell this document without authorization from ASME and CSA Group ; or. make an electronic copy of this document.If you do not agree with any of the terms and conditions contained in this Legal Notice, you may not load or use this document or make any

15、 copies of the contents hereof, and if you do make such copies, you are required to destroy them immediately. Use of this document constitutes your acceptance of the terms and conditions of this Legal Notice.Standards Update ServiceASME A112.19.1-2013/CSA B45.2-13July 2013Title: Enamelled cast iron

16、and enamelled steel plumbing fixturesPagination: 33 pages (xii preliminary and 21 text), each dated July 2013To register for e-mail notification about any updates to this publication go to shop.csa.caclick on CSA Update ServiceThe List ID that you will need to register for updates to this publicatio

17、n is 2422140.If you require assistance, please e-mail techsupportcsagroup.org or call 416-747-2233.Visit CSA Groups policy on privacy at csagroup.org/legal to find out how we protect your personal information.TMA trade-mark of the Canadian Standards Association, operating as “CSA Group”Published in

18、July 2013 by CSA GroupA not-for-profit private sector organization5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N61-800-463-6727 416-747-4044Visit our Online Store at shop.csa.caASME A112.19.1-2013/CSA B45.2-13Enamelled cast iron and enamelled steel plumbing fixturesPublished in Ju

19、ly 2013 by CSA GroupA not-for-profit private sector organization5060 Spectrum Way, Suite 100Mississauga, Ontario, CanadaL4W 5N61-800-463-6727 g120 416-747-4044Visit the CSA Online Store at shop.csa.caISBN 978-1-77139-052-1 2013 CSA GroupAll rights reserved. No part of this publication may be reprodu

20、ced in any form whatsoever without the prior permission of the publisher.Commitment for AmendmentsThis Standard is issued jointly by the American Society of Mechanical Engineers (ASME) and the Canadian Standards Association (Operating as “CSA Group”). Amendments to this Standard will be made only af

21、ter processing according to the Standards writing procedures of both ASME and CSA Group.The American Society of Mechanical Engineers (ASME) T ark AvenueNew York, NY 10016-5990USAwww.asme.orgISBN 978-0-7918-6909-3 Copyright 2013The 2013 edition of this Standard is being issued with an automatic adden

22、da subscription service. The use of addenda allows revisions made in response to public review comments or committee actions to be published as necessary.wo PJuly 2013 iiiContents 2013 CSA Group Enamelled cast iron and enamelled steel plumbing fixturesASME A112 Standards Committee on Plumbing Materi

23、als and Equipment vASME A112.19.1 Project Team on Enameled Cast Iron Plumbing Fixtures (A112) viiCSA Technical Committee on Plumbing Fixtures (B45) viiiCSA/ASME Harmonization Task Group on Plumbing Fixtures (B45-JHTG) xPreface xi0 Introduction 11Scope 12 Reference publications 23 Definitions 34 Gene

24、ral requirements 44.1 General 44.1.1 Materials 44.1.2 Surface finish 44.1.3 Quality of work 44.1.4 Wall brackets 54.2 Cast iron thickness 54.3 Tolerances 54.3.1 General 54.3.2 Apron bathtubs 54.4 Enamel 54.4.1 General 54.4.2 Specular gloss 54.4.3 Reflectance 54.4.4 Enamel thickness 54.4.5 Surface tr

25、eatments 54.5 Waste fitting openings, drainage, and overflows 54.5.1 Waste fitting openings and drainage 54.5.2 Overflows 64.6 Additional requirements for lavatories and sinks Openings and mounting surfaces for supply fittings 64.7 Additional requirements for bathtubs and shower bases 64.7.1 Minimum

26、 dimensions for bathtubs 64.7.2 Slope to the waste outlet 64.7.3 Flanges 64.7.4 Slip-resistant surfaces 74.8 Additional requirements for drinking fountains 74.9 Accessible design fixtures 75 Test methods 75.1 Acid resistance test 75.1.1 Procedure 75.1.2 Performance 7 The American Society of Mechanic

27、al EngineersASME A112.19.1-2013/CSA B45.2-13 2013 CSA Groupiv July 20135.2 Surface examination 85.2.1 Procedure 85.2.2 Performance 85.3 Warpage test 85.3.1 Procedure 85.3.2 Performance 85.4 Field-installed tiling-flange seal test 85.4.1 Procedure 85.4.2 Performance 85.5 Overflow test 95.5.1 Procedur

28、e 95.5.2 Performance 95.6 Structural integrity tests for enamelled steel bathtubs, lavatories, and sinks 95.6.1 Bathtubs 95.6.2 Lavatories and sinks 105.6.3 Surface examination 116 Markings, packaging, and literature 116.1 General 116.2 Non-standard fixtures 126.3 Field-installed flanges 126.4 Packa

29、ging 12AnnexesA (informative) Unit conversion criteria 21Tables1 Maximum allowable number of defects on fixtures 13Figures1 Waste outlet dimensions 142 Opening and mounting surface dimensions for standard 200 mm (8 in) deck fittings 153 Opening and mounting surface dimensions for standard 200 mm (8

30、in) combination fittings 154 Opening and mounting surface dimensions for standard 100 mm (4 in) centre-set fittings 165 Opening and mounting surface dimensions for standard 200 mm (8 in) combination fittings 166 Opening and mounting surface dimensions for single-mount supply fittings 177 Dimensions

31、for bathtubs 188 Slip-resistant surface dimensions for bathtubs 199 Clearance for drinking fountains 20 The American Society of Mechanical Engineers 2013 CSA GroupEnamelled cast iron and enamelled steel plumbing fixturesJuly 2013 vASME A112 Standards Committee on Plumbing Materials and EquipmentD.W.

32、 Viola IAPMO,Mokena, Illinois, USAChairR.H. Ackroyd Rand Technical Consulting,Newburyport, Massachusetts, USAR.K. Adler City of San Jose,San Jose, California, USAS.F. Aridi NSF International,Ann Arbor, Michigan, USAJ.A. Ballanco JB Engineering (b) deletion of the following definitions:(i) Lifting;(i

33、i) Orange peel;(iii) Pinhole; and(iv) Pop-off;(c) amendment of the definition for “Lump”;(d)shower outlet dimensions have been added;(e) alternative slip resistant coverage has been added;(f) the warpage test has been amended for clarity;(g) the flange test has been amended to make it consistent wit

34、h other standards; and(h) other editorial changes were made for better clarification.This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.This Standard was prepared by the ASME/CSA Joint Harmonization Task Group on Plumbing Fixtures, under th

35、e jurisdiction of the ASME Standards Committee on Plumbing Materials and Equipment and the CSA Technical Committee on Plumbing Fixtures. The CSA Technical Committee operates under the jurisdiction of the CSA Strategic Steering Committee on Construction and Civil Infrastructure. This Standard has bee

36、n formally approved by the ASME Standards Committee and the CSA Technical Committee. This Standard was approved as an American National Standard by the American National Standards Institute on June 26, 2013.ASME Notes: (1) This standard was developed under procedures accredited as meeting the criter

37、ia for American National Standards and it is an American National Standard. The Standards Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an opportunity to participate. The proposed Standard was made available for p

38、ublic review and comment that provides an opportunity for additional public input from industry, academia, regulatory agencies, and the public-at-large.(2) ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.(3) ASME does not take any position with r

39、espect to the validity of any patent rights asserted in connection with any items mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable letters patent, nor assume any such liability. Users of a standard are expre

40、ssly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their own responsibility.(4) Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government or industry

41、endorsement of this standard. (5) ASME accepts responsibility for only those interpretations of this document issued in accordance with the established ASME procedures and policies, which precludes the issuance of interpretations by individuals.(6) ASME issues written replies to inquiries concerning

42、 interpretation of technical aspects of this Standard. All inquiries regarding this Standard, including requests for interpretations, should be addressed to:Secretary, A112 Standards CommitteeThe American Society of Mechanical EngineersThree Park AvenueNew York, NY 10016-5990A request for interpreta

43、tion should be clear and unambiguous. The request should cite the applicable edition of the Standard for which the interpretation is being requested. phrase the question as a request for an interpretation of a specific requirement suitable for general understanding The American Society of Mechanical

44、 EngineersASME A112.19.1-2013/CSA B45.2-13 2013 CSA Groupxii July 2013and use, not as a request for an approval of a proprietary design or situation. The inquirer may also include any plans or drawings, which are necessary to explain the question; however, they should not contain proprietary names o

45、r information.ASME procedures provide for reconsideration of any interpretation when or if additional information that might affect an interpretation is available. Further, persons aggrieved by an interpretation may appeal to the cognizant ASME Committee.Interpretations are published on the ASME Web

46、 site under the Committee Pages at http:/www.asme.org/codes/ as they are issued.CSA Notes: (1) Use of the singular does not exclude the plural (and vice versa) when the sense allows.(2) Although the intended primary application of this Standard is stated in its Scope, it is important to note that it

47、 remains the responsibility of the users of the Standard to judge its suitability for their particular purpose.(3) This publication was developed by consensus, which is defined by CSA Policy governing standardization Code of good practice for standardization as “substantial agreement. Consensus impl

48、ies much more than a simple majority, but not necessarily unanimity”. It is consistent with this definition that a member may be included in the Technical Committee list and yet not be in full agreement with all clauses of this publication.(4) CSA Standards are subject to periodic review, and sugges

49、tions for their improvement will be referred to the appropriate committee.(5) All enquiries regarding this Standard, including requests for interpretation, should be addressed to Canadian Standards Association, 5060 Spectrum Way, Suite 100, Mississauga, Ontario, Canada L4W 5N6. Requests for interpretation should(a) define the problem, making reference to the specific clause, and, where appropriate, include an illustrative sketch;(b) provide an explanation of circumstances surrounding the actual field condition; and(c) be phrased where possibl