ASME B16 29-2007 Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings DWV (B16 29 - 2007)《可锻铜和可锻铜合金软钎焊连接排水配件 DWV》.pdf

1、Wrought Copper and Wrought Copper Alloy Solder-Joint Drainage Fittings DWVAN AMERICAN NATIONAL STANDARDASME B16.29-2007(Revision of ASME B16.29-2001)Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,

2、-ASME B16.29-2007(Revision of ASME B16.29-2001)Wrought Copperand WroughtCopper AlloySolder-JointDrainageFittings DWVAN AMERICAN NATIONAL STANDARDThree Park Avenue New York, NY 10016Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permit

3、ted without license from IHS-,-,-Date of Issuance: October 5, 2007The next edition of this Standard is scheduled for publication in 2012. There will be no addendaissued to this edition.ASME issues written replies to inquiries concerning interpretations of technical aspects of thisStandard. Interpret

4、ations are published on the ASME Web site under the Committee Pages athttp:/cstools.asme.org as they are issued.ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria for American Nation

5、alStandards. The Standards Committee that approved the code or standard was balanced to assure that individuals fromcompetent and concerned interests have had an opportunity to participate. The proposed code or standard was madeavailable for public review and comment that provides an opportunity for

6、 additional public input from industry, academia,regulatory agencies, and the public-at-large.ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.ASME does not take any position with respect to the validity of any patent rights asserted in connection

7、 with anyitems mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability forinfringement of any applicable letters patent, nor assume any such liability. Users of a code or standard are expresslyadvised that determination of the validity of any such p

8、atent rights, and the risk of infringement of such rights, isentirely their own responsibility.Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted asgovernment or industry endorsement of this code or standard.ASME accepts responsibility fo

9、r only those interpretations of this document issued in accordance with the establishedASME procedures and policies, which precludes the issuance of interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior

10、written permission of the publisher.The American Society of Mechanical EngineersThree Park AvenueNew York, NY 10016-5990Copyright 2007 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright ASME International Provided by IHS under license with ASME Not for Resale

11、No reproduction or networking permitted without license from IHS-,-,-CONTENTSForeword ivCommittee Roster . vCorrespondence With the B16 Committee viSummary of Changes vii1 Scope . 12 Description 13 Pitch (Slope) 14 Abbreviations 15 Component Size . 16 Marking. 27 Material. 28 Laying Lengths 29 Ovali

12、ty 210 Threaded Ends. 211 Design of Threaded Ends . 212 Alignment . 213 Gauging. 2Figure1 Size of Fittings . 5Tables1 Dimensions of Solder-Joint Ends 32 Dimensions of Threaded Ends DWV . 43 Dimensions of DWV Couplings, Extended Bushings, and Adapters 64 Dimensions of DWV Soil Pipe Adapters . 75 Dime

13、nsions of DWV C H11547 No-Hub Soil Pipe Adapter 86 Dimensions of DWV Elbows 97 Dimensions of DWV 45 deg Ys . 108 Dimensions of DWV Tees . 119 Dimensions of DWV Caps 1110 Dimensions of DWV Vent Increasers 1211 Dimensions of DWV Closet Flanges . 1312 Dimensions of DWV Trap Adapters . 1413 Dimensions o

14、f DWV Slip Joint Ends 14Mandatory AppendicesI U.S. Customary Dimensions 15II References 27Nonmandatory AppendixA Quality System Program 28iiiCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-FOREWOR

15、DStandardization of cast and wrought solder-joint fittings was initiated in Subcommittee 11 ofAmerican Standards Association (ASA) Sectional Committee A40 on Plumbing Requirementsand Equipment. Development work culminated in publication of ASA A40.3-1941.In 1949, work on these fittings was transferr

16、ed to Sectional Committee B16 of ASA, whichestablished Subcommittee 9 (now Subcommittee J). The first standard developed was approvedas ASA B16.18-1950, Cast Bronze Solder-Joint Fittings. A later joint effort of the Copper and BrassResearch Association and the Manufacturers Standardization Society o

17、f the Valve and FittingsIndustry(MSS) culminatedina standardonwrought fittings,ultimatelyapproved asB16.22-1951.Concurrently,recognizingtheneedfordrainagefittingstandards,anMSStaskgroupdevelopedthe standard later approved as ASA B16.23-1953, Cast Bronze Solder-Joint Drainage Fittings, anda standard

18、for wrought fittings was initially published as MSS SP-64-1961. A revision of thatstandard was submitted to Subcommittee 9 of B16 and was eventually approved as ASAB16.29-1966.A revision was published after reorganization of ASA as the American National StandardsInstitute (ANSI) as ANSI B16.29-1973.

19、 In this edition, shorter solder cups were specified in largersizes, since strength to contain pressure is not a factor. In 1979, Subcommittee I (formerly 9,now J) added metric dimensional equivalents and made other minor improvements. That revisionwas approved by ANSI, after approval by the Committ

20、ee and secretariat organizations, as ANSIB16.29-1980.In 1982, American National Standards Committee B16 was reorganized as an ASME Committeeoperating under procedures accredited by ANSI. The 1986 edition of the standard removedmetric equivalents (not functionally applicable in the plumbing industry)

21、, updated the referencedstandards, and incorporated editorial and format revisions. The 1994 edition removed inspectiontolerance requirements, established minimum laying lengths, added soil pipe adapters, andincorporated editorial revisions. Following approval by the Standards Committee and ASME,app

22、roval as an American National Standard was given by ANSI on October 10, 1994, with thedesignator ASME B16.29-1994.The 2001 Edition of this Standard was revised to include Nonmandatory Appendix B, QualitySystemProgram.Editorialrevisionsweremadeforthepurposeofclarification.Followingapprovalby the B16

23、Main Committee and ASME Supervisory Board, this Standard was approved as anAmerican National Standard by ANSI on October 11, 2001.Inthis2007Edition,metricunitsaretheprimaryreferenceunitswhilemaintainingU.S.Custom-ary Units in either parenthetical or separate forms. In addition, several editorial rev

24、isions havebeen made for clarity. Following approval by the B16 Standards Committee and the ASMESupervisory Board, and after public review, this Standard was approved as an American NationalStandard by ANSI on August 20, 2007.Requests for interpretation or suggestions for revision should be sent to

25、the Secretary, B16Committee, The American Society of Mechanical Engineers, Three Park Avenue, New York, NewYork 10016-5990.ivCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASME B16 COMMITTEEStand

26、ardization of Valves, Flanges, Fittings, and Gaskets(The following is the roster of the Committee at the time of approval of this Standard.)STANDARDS COMMITTEE OFFICERSH. R. Sonderegger, ChairM. L. Nayyar, Vice ChairU. DUrso, SecretarySTANDARDS COMMITTEE PERSONNELR. W. Barnes, Anric EnterprisesW. B.

27、 Bedesem, ExxonMobil Research however, theyshould not contain proprietary names or information.Requests that are not in this format will be rewritten in this format by the Committee priorto being answered, which may inadvertently change the intent of the original request.ASME procedures provide for

28、reconsideration of any interpretation when or if additionalinformation that might affect an interpretation is available. Further, persons aggrieved by aninterpretation may appeal to the cognizant ASME Committee or Subcommittee. ASME does not“approve,” “certify,” “rate,” or “endorse” any item, constr

29、uction, proprietary device, or activity.Attending Committee Meetings. TheB16StandardsCommitteeregularlyholdsmeetings,whichare open to the public. Persons wishing to attend any meeting should contact the Secretary ofthe B16 Standards Committee.viCopyright ASME International Provided by IHS under lice

30、nse with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-ASME B16.29-2007SUMMARY OF CHANGESFollowing approval by the ASME B16 Committee and ASME, and after public review, ASMEB16.29-2007 was approved by the American National Standards Institute on August 20, 2

31、007.ASME B16.29-2007 includes the following changes identified by a margin note, (07).Page Location Change1, 2 1 (1) Paragraphs 1.1 and 1.2 revised(2) Paragraphs 1.3 and 1.4 added(3) Former para. 1.3 revised andredesignated as 1.52 Revised3 Revised5 Subparagraphs (a) and (b) revised10.2 Revised10.3

32、Revised12 Revised13 Revised in its entirety3 Table 1 Revised4 Table 2 Revised6 Table 3 Revised7 Table 4 Revised8 Table 5 Revised9 Table 6 Revised10 Table 7 Revised11 Table 8 RevisedTable 9 Revised12 Table 10 Revised13 Table 11 Revised14 Table 12 RevisedTable 13 Revised15 Mandatory Appendix I Added27

33、 Mandatory Appendix II Revised in its entirety28 Nonmandatory Appendix A Title revisedviiCopyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-viiiCopyright ASME International Provided by IHS under lice

34、nse with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-(07)ASME B16.29-2007WROUGHT COPPER AND WROUGHT COPPER ALLOYSOLDER-JOINT DRAINAGE FITTINGS DWV1 SCOPE1.1 GeneralThis Standard for wrought copper and wrought cop-per alloy solder-joint drainage fittings, d

35、esigned for usewith copper drainage tube conforming to ASTM B 306,covers the following:(a) description(b) pitch (slope)(c) abbreviations for end connections(d) sizes and method of designating openings forreducing fittings(e) marking(f) material(g) dimensions and tolerances1.2 ConventionFor the purpo

36、se of determining conformance withthisStandard,theconventionforfixingsignificantdigitswherelimits(maximumandminimumvalues)arespeci-fied shall be rounding off as defined in ASTM E 29. Thisrequires that an observed or calculated value shall berounded off to the nearest unit in the last right-handdigit

37、 used for expressing the limit. Decimal values andtolerances do not imply a particular method of mea-surement.1.3 Relevant UnitsThis Standard states values in both metric and U.S.Customary units. These systems of units are to beregarded separately as standard. Within the text, theU.S. Customary unit

38、s are shown in parentheses or inseparate tables. (Tables showing dimensions in equiva-lent U.S. Customary units are found in MandatoryAppendix I.) The values stated in each system are notexact equivalents; therefore, it is required that each sys-temofunitsbeusedindependentlyoftheother.Combin-ing val

39、ues from the two systems constitutesnonconformance with the standard.1.4 ReferencesCodes, standards, and specifications, containing pro-visions to the extent referenced herein, constituterequirements of this Standard. These reference docu-ments are listed in Mandatory Appendix II.11.5 Quality System

40、sGuidelines relating to the product manufacturersquality system programs are described in Nonmanda-tory Appendix A.2 DESCRIPTIONThese fittings are designed for drainage and vent sys-tems only, using the solder-joint method of connection.The fitting cups (C) are provided with stops so thatthe ends of

41、 the tube, when assembled, meet the stops.Sketches and designs of fittings are illustrative only. Thedimensions specified herein shall govern in all cases.3 PITCH (SLOPE)All nominal 90-deg fittings shall be pitched to resultin a slope of 0.20 mm/m (0.25 in./ft) (2%) of horizontaltube length with ref

42、erence to a horizontal plane.4 ABBREVIATIONSThe symbols shown below are used to designate thetype of fitting end.Symbols DefinitionsC Solder-joint fitting end (female) made to receivecopper tube diameterFTG Solder-joint fitting end (male) made to coppertube diameterF Internal American National Stand

43、ard taper pipethread (female) NPTIM External American National Standard taper pipethread (male) NPTESJ End of fitting formed to receive outside diame-ter tube sizeNPSM American National Standard straight mechani-cal pipe thread5 COMPONENT SIZE5.1 Nominal SizeAs applied in this Standard, the use of t

44、he phrase“nominal size” followed by a dimensionless number isfor the purpose of fitting end connection size identifi-cation.(07)(07)(07)(07)Copyright ASME International Provided by IHS under license with ASME Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-(07)ASME

45、 B16.29-20075.1.1 Tube. The size designations for the fitting endconfigurations defined in Table 1 (Table I-1) correspondto drainage tube sizes defined in ASTM B 306.5.1.2 Pipe. The size designation of threaded fittingend configurations defined in Table 2 (Table I-2) corres-ponds to thread sizes def

46、ined in ASME B1.20.1.5.2 IdentificationFittings shall be identified by the nominal size of theopenings in the sequence illustrated in Fig. 1.6 MARKINGEach fitting shall be marked permanently and legiblywith the manufacturers name or trademark and withDWV (to indicate drain-waste-vent).7 MATERIALFitt

47、ings shall be made of wrought copper or wroughtcopperalloymaterialhavingnotlessthan84%ofcoppercontent.8 LAYING LENGTHSDue to widely varying manufacturing processes, lay-ing length dimensions of fittings are not standardized.Consult the manufacturer for these dimensions. Sug-gested dimensions, includ

48、ing laying lengths, for variousfitting configurations are shown in Tables 3 through 13(Tables I-3 through I-13).9 OVALITYMaximum ovality shall not exceed 1% of the maxi-mum diameter shown in Table 1. The average of themaximum and minimum diameters must be within thedimensions shown in the table.10 T

49、HREADED ENDS10.1 GeneralFitting threads shall be right hand, conforming toASME B1.20.1-1983 (R2001). They shall be taper threads(NPT), except for slip joint ends, which shall havestraight pipe threads (NPSM).10.2 ChamferAll internal threads shall be countersunk a distancenot less than one-half the pitch of the thread a