ASTM A100-2007 Standard Specification for Ferrosilicon《硅铁的标准规范》.pdf

1、Designation: A 100 07Standard Specification forFerrosilicon1This standard is issued under the fixed designation A 100; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the

2、 year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers grades of ferrosilicon forsteelmaking and foundry uses.1.2 The values stated in inch-pound units are to be regardedas the standard. The metric

3、 equivalents of inch-pound units (SIunits) given in parentheses may be approximate.2. Referenced Documents2.1 ASTM Standards:2A 1025 Specification for Ferroalloys and Other AlloyingMaterials, General RequirementsE11 Specification for Wire Cloth and Sieves for TestingPurposesE 360 Test Methods for Ch

4、emical Analysis of Silicon andFerrosilicon33. General Conditions of Delivery3.1 Materials furnished to this specification shall conform tothe requirements of Specification A 1025, including anysupplementary requirements that are indicated in the purchaseorder. Failure to comply with the general requ

5、irements ofSpecification A 1025 constitutes nonconformance with thisspecification. In case of conflict between the requirements ofthis specification and Specification A 1025, this specificationshall prevail.4. Chemical Composition4.1 The various grades shall conform to the requirements asto chemical

6、 composition prescribed in Table 1.4.2 The manufacturer shall furnish an analysis of eachshipment showing the silicon content and when required, suchof the other elements specified in Table 1.5. Size5.1 The various grades are available in sizes as listed inTable 2.5.2 The sizes listed in Table 2 are

7、 typical as shipped fromthe manufacturers plant. These alloys exhibit varying degreesof friability; therefore, some attrition may be expected intransit, storage, and handling. A quantitative test is not avail-able for rating relative friability of ferroalloys. A code systemhas been developed, theref

8、ore, for this purpose, and a numberrating for each product type is shown in the last column ofTable 2. Definitions applicable to these code numbers are givenin Specification A 1025.6. Chemical Analysis6.1 Unless otherwise agreed upon, the chemical analysis ofthe material shall be made in accordance

9、with Test MethodsE 360.6.2 If alternative methods of analysis are used, MethodsE 360 shall be used for referee.6.3 Where a method is not given in Methods E 360 for theanalysis for a particular element, the analysis shall be made inaccordance with a procedure agreed upon between the manu-facturer and

10、 the purchaser.7. Keywords7.1 ferroalloy; ferrosilicon1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.18 on Castings.Current edition approved March 1, 2007. Published March 2007. Origi

11、nallyapproved in 1925. Last previous edition approved in 1993 as A 100 04.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe

12、ASTM website.3Withdrawn.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.TABLE1ChemicalRequirementsElementGradeCCACBC1C2DDAEEAE1FF1F1AGGAG1G1AComposition,%A,BSilicon74.

13、079.074.079.074.079.074.079.074.079.065.070.065.070.047.051.047.051.047.051.020.024.020.024.020.024.014.017.014.017.014.017.014.017.0Carbon0.100.100.100.100.100.100.10.010.0100.100.500.500.500.700.700.700.70Sulfur0.0250.0250.0250.0250.0250.0250.0250.0250.0250.0250.0250.0250.0250.0250.0250.0250.025Ph

14、osphorous0.0350.0350.0350.0350.0350.0350.0350.0400.0400.0400.1200.1200.1200.1200.1200.1200.120Aluminum1.500.500.101.001.501.001.501.250.101.250.401.251.001.001.000.750.750.750.75Manganese0.400.400.400.400.400.500.500.750.750.751.001.001.001.251.25Calciumfvariant30.501.50Boron0.040.100.040.100.040.10

15、0.040.100.040.10AAsinglevalueindicatesamaximum,exceptforcalcium.BWhenshippedin3000lbcontainers,theaverageboroncontentofacontainershallnotvaryfromtheaveragereportedfortheentireshipmentbymorethan0.010%.A100072SUPPLEMENTARY REQUIREMENTSThe composition shall be further limited to the requirements of Tab

16、le S1.1. Upon request of thepurchaser, the manufacturer shall furnish an analysis of these elements on a schedule agreed betweenthe manufacturer and purchaser.TABLE 2 Standard Sizes and TolerancesGrades Standard SizesTolerances and Sieve Sizes Defined byASTM Specification E11FriabilityRatingAC,D,E 8

17、-in. (203-mm) by 4-in.(102-mm)90-lb (40.8-kg) lump, max 10 %, max, passing 4-in. (102-mm)sieve8-in. (203-mm) by 2-in.(50.8-mm)90-lb (40.8-kg) lump, max 10 %, max, passing 2-in. (50.8-mm)sieve5-in. (127-mm) by 2-in.(50.8-mm)10 %, max, retained on 5-in. (127-mm)sieve10 %, max, passing 2-in. (50.8-mm)s

18、ieve4-in. (102-mm) by12-in.(12.7-mm)10 %, max, retained on 4-in. (102-mm)sieve10 %, max, passing12-in. (12.7-mm)sieve4-in. (102-mm) by down 10 %, max, retained on 4-in. (102-mm)sieve12 %, max, passing14-in. (6.35-mm)sieve3-in. (76.2-mm) by12-in.(12.7-mm)10 %, max, retained on 3-in. (76.2-mm)sieve15

19、%, max, passing12-in. (12.7-mm)sieve3-in. (76.2-mm) by down 10 %, max, retained on 3-in. (76.2-mm)sieve15 %, max, passing No. 8 (2.38-mm)sieve2-in. (50.8-mm) by12 in. (12.7-mm) 10 %, max, retained on 2-in. (50.8-mm)sieve15 %, max, passing12-in. (12.7-mm)sieve2-in. (50.8-mm) by down 10 %, max, retain

20、ed on 2-in. (50.8-mm)sieve15 %, max, passing No. 8 (2.38-mm)sieve1-in. (25.4-mm) by No. 8(2.38-mm)5 %, max, retained on 1-in. (25.4-mm)sieve10 %, max, passing No. 8 (2.38-mm)sieve1-in. (25.4-mm) by down 5 %, max, retained on 1-in. (25.4-mm)sieve20 %, max, passing No. 8 (2.38-mm)sieveC,D,F Lump or Pi

21、g 90-lb (40.8-kg) lump or pig, maxC,D,E12-in. (12.7-mm) by No. 8 (2.38-mm) 5 %, max, retained on12-in. (12.7-mm)sieve10 %, max, passing No. 8 (2.38-mm)sieve38-in. (9.51-mm) by No. 6(3.36-mm)5 %, max, retained on38-in. (9.51-mm)sieve10 %, max, passing No. 6 (3.36-mm)sieve38-in. (9.51-mm) by No. 12 (1

22、.68-mm) 5 %, max, retained on38-in. (9.51-mm)sieve10 %, max, passing No. 14 (1.41-mm)sieve38-in. (9.51-mm) by down 5 %, max, retained on38-in. (9.51-mm)sieve15 %, max, passing No. 70 (0.21-mm)sieve14-in. (6.35-mm) by down 5 %, max, retained on14-in. (6.35-mm)sieveNo. 8 (2.38-mm) by down 5 %, max, re

23、tained on No. 8 (2.38-mm)sieveNo. 28 (841-em) by down 5 %, max, retained on No. 20 (841-em)sieveG pig 90-lb (40.8-kg) pig, max.ASee Appendixes.A100073TABLES1.1SupplementaryChemicalRequirementsElementGradeCCACBC1C2DDAEEAE1E1AFF1F1AGGAG1G1AComposition,%maximumChromium0.300.300.300.500.500.500.500.150.

24、150.250.250.250.250.25Nickel0.100.100.100.200.200.300.30Copper0.100.100.100.200.200.300.30Titanium0.200.200.200.200.200.200.200.200.200.200.200.200.200.20A100074APPENDIX(Nonmandatory Information)X1. FRIABILITY RATINGSX1.1 Proposed friability ratings are shown in Table X1.1 asfollows:TABLE X1.1 Propo

25、sed Friability Ratings for FerrosiliconProductGradeProposedFriabilityRatingC4D4E5F4G2A100075SUMMARY OF CHANGESCommittee A01 has identified the location of selected changes to this standard since the last issue (A 100 04) that may impact the use of this standard.(1) Revised Table 1 and footnotes to T

26、able 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such righ

27、ts, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional

28、standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM

29、Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).A100076