ASTM A1003 A1003M-2011e1 Standard Specification for Steel Sheet Carbon Metallic- and Nonmetallic-Coated for Cold-Formed Framing Members《带金属及非金属涂层的冷成形框架构件的碳钢薄板标准规格》.pdf

1、Designation: A1003/A1003M 111Standard Specification forSteel Sheet, Carbon, Metallic- and Nonmetallic-Coated forCold-Formed Framing Members1This standard is issued under the fixed designation A1003/A1003M; the number immediately following the designation indicates theyear of original adoption or, in

2、 the case of revision, the year of last revision. A number in parentheses indicates the year of lastreapproval. A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorially corrected Table 1 in October 2011.1. Scope*1.1 This specification covers coate

3、d steel sheet used in themanufacture of cold-formed framing members, such as, but notlimited to, studs, joists, purlins, girts, and track.1.2 The steel sheet used for cold-formed framing membersincludes metallic-coated, painted metallic-coated, or paintednonmetallic-coated.1.3 The values stated in e

4、ither inch-pound or SI units shallbe regarded separately as standard. Within the text, SI units areshown in brackets. The values stated in each system are notexact equivalents; therefore, each system shall be used inde-pendently of the other.1.4 Unless the order specifies the “M” designation SIunits

5、, the product shall be furnished to inch-pound units.1.5 The text of this specification references notes andfootnotes, which provide explanatory material. These notes andfootnotes, excluding those in tables and figures, shall not beconsidered as requirements of this specification.2. Referenced Docum

6、ents2.1 ASTM Standards:2A463/A463M Specification for Steel Sheet, Aluminum-Coated, by the Hot-Dip ProcessA568/A568M Specification for Steel, Sheet, Carbon, Struc-tural, and High-Strength, Low-Alloy, Hot-Rolled andCold-Rolled, General Requirements forA653/A653M Specification for Steel Sheet, Zinc-Coa

7、ted(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)by the Hot-Dip ProcessA755/A755M Specification for Steel Sheet, MetallicCoated by the Hot-Dip Process and Prepainted by theCoil-Coating Process for Exterior Exposed Building Prod-uctsA792/A792M Specification for Steel Sheet, 55 %Aluminum-Zinc A

8、lloy-Coated by the Hot-Dip ProcessA875/A875M Specification for Steel Sheet, Zinc-5 % Alu-minum Alloy-Coated by the Hot-Dip ProcessA879/A879M Specification for Steel Sheet, Zinc Coated bythe Electrolytic Process for Applications Requiring Desig-nation of the Coating Mass on Each SurfaceA902 Terminolo

9、gy Relating to Metallic Coated Steel Prod-uctsA924/A924M Specification for General Requirements forSteel Sheet, Metallic-Coated by the Hot-Dip ProcessA941 Terminology Relating to Steel, Stainless Steel, Re-lated Alloys, and FerroalloysA1004/A1004M Practice for Establishing Conformance tothe Minimum

10、Expected Corrosion Characteristics of Me-tallic, Painted-Metallic, and Nonmetallic-Coated SteelSheet Intended for Use as Cold Formed Framing MembersA1063/A1063M Specification for Steel Sheet, Twin-RollCast, Zinc-Coated (Galvanized) by the Hot-Dip ProcessC645 Specification for Nonstructural Steel Fra

11、ming Mem-bersC955 Specification for Load-Bearing (Transverse andAxial) Steel Studs, Runners (Tracks), and Bracing orBridging for ScrewApplication of Gypsum Panel Productsand Metal Plaster BasesD714 Test Method for Evaluating Degree of Blistering ofPaintsD1005 Test Method for Measurement of Dry-Film

12、Thick-ness of Organic Coatings Using MicrometersD1654 Test Method for Evaluation of Painted or CoatedSpecimens Subjected to Corrosive EnvironmentsD4138 Practices for Measurement of Dry Film Thickness ofProtective Coating Systems by Destructive, Cross-Sectioning Means1This specification is under the

13、jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direct responsibility ofSubcommittee A05.11 on Sheet Specifications.Current edition approved May 1, 2011. Published May 2011. Originallyapproved in 2000. Last previous edition approved in 2010 as A1003/A1003M - 1

14、0.DOI: 10.1520/A1003_A1003M-11E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes sect

15、ion appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.D4145 Test Method for Coating Flexibility of PrepaintedSheet2.2 ISO Standard:ISO 9223 Corrosion of Metals and AlloysCorrosivity ofAtmospheres-Clas

16、sification32.3 AISI Standard:Specification for the Design of Cold-Formed Steel StructuralMembers43. Terminology3.1 DefinitionsSee Terminology A902 for definitions ofgeneral terminology relating to metallic-coated steel products,and Terminology A941 for definitions of general terminologyrelating to u

17、ncoated steel sheet products.3.2 Definitions of Terms Specific to This Standard:3.2.1 coating sequence, nthe unbroken or uninterruptedmanufacture of coils of the same coating designation.3.2.2 coil coater, nthe organization that applies paint filmcoatings to coils of steel sheet on continuous paint

18、lines.3.2.3 producer, nthe organization that produces the steelsheet coil product from which the cold-formed members arefabricated.3.2.4 purlins and girts, nhorizontal structural membersthat support roof deck or panel covering with loads appliedprincipally by bending.3.2.5 resample, nadditional test

19、s made when the originaltest results do not satisfy the specification requirements.3.2.6 retest, nadditional test, or tests, made when theoriginal test results do not satisfy the specification require-ments and the failure is due to a mechanical condition of thetest specimen.3.2.7 roll former, nthe

20、organization that produces thecold-formed members.3.2.8 zinc-iron alloy, na dull grey coating with no spanglepattern that is produced on hot-dip zinc-coated steel sheet.3.2.8.1 DiscussionZinc-iron alloy-coating is normallydull gray in appearance when produced by the manufacture ofthe coated sheet. T

21、ypically, the coating contains between 8 and12 % iron, which is the result of a diffusion reaction betweenthe steel sheet and the zinc coating during the coating process.In most applications, this product is intended to be painted. Thecoating offers excellent paint adhesion. When the product isexpos

22、ed to the environment without a paint coating, there is atendency for the development of a rust-colored stain on thesurface. This is caused by the presence of iron in the coating.This stain may be aesthetically objectionable to some users ofcold formed framing members.3.2.9 aluminum coating type 1,

23、na coating of aluminumand silicon alloy on steel sheet.3.2.9.1 DiscussionAluminum-coated steel sheet type 1provides protection from corrosion primarily through thebarrier action of the coating. The aluminum-silicon alloycoating provides galvanic corrosion only in marine environ-ments. Because this c

24、oating does not generally provide gal-vanic protection, rust staining may be evident at area where thebase metal is exposed to the environment, such as at punch-outs, cut or sheared edges of members, and at scratches.3.2.10 aluminum coating type 2, na coating of commer-cially pure aluminum on steel

25、sheet.3.2.10.1 DiscussionAluminum-coated steel sheet type 2provides protection from corrosion primarily through thebarrier action of the coating. The aluminum coating providesgalvanic corrosion only in marine environments. Because thiscoating does not generally provide galvanic protection, ruststain

26、ing may be evident at areas where the base metal isexposed to the environment such as at punch-outs, cut orsheared edges of members, and at scratches.3.3 Suffxes:H, adjhigh ductility.L, adjlow ductility.NS, adjnonstructural.3.3.1 These designations are associated with aspects of theend uses of the s

27、teel products; H and L are associated withstructural or load-bearing applications, and NS with nonstruc-tural or nonload-bearing applications.4. Classification4.1 The steel sheet is available in the following designa-tions:4.1.1 Structural Grade 33, 37, 40, 50, 55, 60, 70, and 80Type H (for example,

28、 ST50H), Structural Grade 230, 255, 275,340, 380, 410, 480, and 550 Type H for example, ST340H.4.1.2 Structural Grade 33, 37, 40, 50, 55, 60, 70, and 80Type L (for example, ST50L), Structural Grade 230, 255, 275,340, 380, 410, 480, and 550 Type L for example, ST340L.4.1.3 Nonstructural Grade 33, 40,

29、 50, 57, 60, 65, 70, and 80(for example, NS33), Nonstructural Grade 230, 275, 340, 395,420, 450, 480, 550 for example, NS230).NOTE 1Abbreviated designations are shown in parentheses or brack-ets.4.2 Use of Type L steels is limited to purlins and girts (see3.2.4).5. Ordering Information5.1 Steel shee

30、t in coils or cut lengths shall be ordered tobase metal thickness requirements expressed in increments of0.0001 in. 0.001 mm.5.2 Orders for product to this specification shall include thefollowing information, as necessary to adequately describe thedesired product.5.2.1 ASTM specification number and

31、 year of issue (A1003 _ for inch-pound units and A1003M _ for SI units),5.2.2 Name of the material (metallic-coated steel sheet),(painted metallic-coated steel sheet), or (painted nonmetallic-coated steel sheet), and designation (see 4.1). For StructuralGrades, if a type is not specified, type H sha

32、ll be furnished.5.2.2.1 See SpecificationA755/A755M for additional order-ing requirements for the painted-metallic-coated steel sheet.5.2.3 Type of coating (metallic-coated; zinc, zinc-iron alloy,55 % aluminum-zinc alloy, zinc-5 % aluminum alloy,3Available from American National Standards Institute

33、(ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from American Iron and Steel Institute (AISI), 1140 ConnecticutAve., NW, Suite 705, Washington, DC 20036, http:/www.steel.org.A1003/A1003M 1112aluminum-coated Type 1, and aluminum-coated Type 2, elec-trolytic zinc-co

34、ated), (painted-metallic-coated; metallic-coating and nonmetallic-coating type), (painted nonmetalliccoated: nonmetallic-coating type).5.2.3.1 Metallic coating weight mass designation (seeTable 1), (see 9.1).5.2.3.2 Nonmetallic coating thickness (see 9.2 or 9.3).5.2.4 Chemically-treated or not chemi

35、cally-treated(metallic-coated only).5.2.5 Oiled or not-oiled,5.2.6 Dimensions (show thickness, width, and flatness re-quirements and length, if cut lengths). Specify the applicabletable of thickness tolerances ofA568/A568M for both metallic-coated and nonmetallic-coated sheet that applies to the ord

36、er,that is, the table of thickness tolerances for38-in. 10-mmedge distance, or the table of thickness tolerances for 1-in.25-mm edge distance.5.2.7 Coil size requirements (specify maximum outsidediameter (OD) acceptable inside diameter (ID), and maximumweight mass.5.2.8 Packaging (specify requiremen

37、ts for banding, paperwrapping and other special packaging requirements).5.2.9 Certification, if required (heat analysis, metallic coat-ing weight or nonmetallic coating thickness and mechanicalproperties report).5.2.10 Special Requirements, if any.5.2.11 When a composition type is not selected (see

38、Table 2)then Class 1 shall be furnished.NOTE 2Typical ordering descriptions are as follows: Steel sheet,zinc-coated, Structural Grade 50 Type H (ST50H),ASTMA1003, CoatingDesignation G60, chemically-treated, not oiled, 0.035 by 48 in. by coil,thickness tolerance Table 3, 24-in ID, 30 000 lb maximum f

39、or steel studs,orSteel sheet, zinc-coated, Structural Grade 230 Type L ST230L, ASTMA1003M, Coating Designation Z180, chemically-treated, not oiled, 1.00mm by 920 mm by coil, thickness tolerance Table 3, 600 mm ID, 10 000kg maximum for purlins.NOTE 3Electrolytic zinc-coated steel sheet designations i

40、ndicate thecoating on one surface only; therefore, the coating requirement must bespecified for each side of the steel sheet as indicated in Table 1. Also, theelectrolytic zinc-coated steel sheet is only available in SI values.6. Materials and Manufacture6.1 The ordered thickness shall be the base m

41、etal thickness.NOTE 4This requirement differs from the normal ordering practice forhot dip metallic-coated products where the ordered thickness includes thebase metal and the coating but is similar to the ordering practice for heavycoating mass electrolytic coated product.7. Chemical Composition7.1

42、Base Metal:7.1.1 The chemical composition of the steel sheet shallconform to the requirements of Table 2, as indicated for theclass selected for the steel.7.1.2 All tests shall be conducted in accordance with therequirements for chemical composition as described in Speci-fication A924/A924M for prod

43、ucts with metallic coatings andSpecification A568/A568M for nonmetallic coated products.7.1.3 An analysis of each heat of steel shall be made by theproducer to determine the percentage of elements specified inTable 2.7.1.4 In those cases where the heat analysis is not availablea product analysis tes

44、t shall be performed to determineconformance with the requirements of Table 2.7.1.5 Each of the elements listed in Table 2 shall be includedin the report of heat or product analysis. When the amount ofcopper, nickel, chromium, or molybdenum is less than 0.02 %,report the analysis as 0.02 % or the ac

45、tual determined value.When the amount of vanadium, columbium, or titanium is lessthan 0.008 %, report the analysis as 0.008 % or the actualdetermined value.8. Mechanical Properties8.1 The mechanical properties of the steel sheet shallconform to the requirements shown in Table 3.8.2 Tests for mechani

46、cal properties of the “H” and “NS”steel designations shall be conducted in accordance with thetests for mechanical properties described in SpecificationA924/A924M for metallic-coated steel sheet andA568/A568Mfor nonmetallic coated steel sheet.8.3 Tests for elongation in12 in. 13 mm of the “L” steeld

47、esignations shall be conducted in accordance with the proce-dure found in the AISI Cold Formed Design Manual, “StandardMethods for Determination of Uniform and Local Ductility.”9. Coating Properties9.1 Metallic CoatingThe minimum metallic coatingweight mass requirements shall be as shown in Table 1.

48、9.1.1 Not all coatings will react the same under a given setof environmental conditions. These minimum coating designa-tions assume normal exposure conditions and constructionpractices. When more severe exposure conditions are probable,for example, in coastal areas, consideration should be given tos

49、pecifying heavier coating weight mass.9.1.2 Other metallic coatings shall be considered for inclu-sion to Table 1 provided they satisfy the minimum expectedcorrosion characteristics as indicated by laboratory testingconducted in accordance with Practice A1004/A1004M.9.1.3 The minimum expected corrosion characteristics asindicated by laboratory testing for metallic coated sheet steelsare as follows:TABLE 1 Coating Weight Mass Requirements(Metallic Coatings)ProductDesignationCoating DesignationType H andType LG60 Z180AA6