ASTM A167-1999(2004) Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate Sheet and Strip《不锈钢和耐热铬镍钢板、薄钢板及带材的标准规范》.pdf

1、Designation: A 167 99 (Reapproved 2004)Standard Specification forStainless and Heat-Resisting Chromium-Nickel Steel Plate,Sheet, and Strip1This standard is issued under the fixed designation A 167; the number immediately following the designation indicates the year oforiginal adoption or, in the cas

2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This spec

3、ification covers stainless and heat-resistingchromium-nickel steel plate, sheet, and strip.1.2 The values stated in inch-pound units are to be regardedas the standard.NOTE 1Grades that were previously covered in both SpecificationsA 167 and A 240/A 240M have been removed from this specification andm

4、ay now be supplied and purchased in compliance with SpecificationA 240/A 240M. The chemical and mechanical property requirements ofthese grades were identical in Specifications A 167 and A 240/A 240M atthe time of removal from Specification A 167.2. Referenced Documents2.1 ASTM Standards:2A 240/A 24

5、0M Specification for Chromium andChromium-Nickel Stainless Steel Plate, Sheet and Strip forPressure Vessels and for General ApplicationsA 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 480/A 480M Specification for General Requirements forFlat-Rolled Stainless and Heat-Resi

6、sting Steel Plate,Sheet, and StripE 527 Practice for Numbering Metals and Alloys (UNS)2.2 SAE Standard:3J 1086 Numbering Metals and Alloys (UNS)3. Chemical Composition3.1 The steel shall conform to the requirements as tochemical composition specified in Table 1, and shall conformto applicable requir

7、ements specified in Specification A 480/A 480M.4. Mechanical Properties4.1 The material shall conform to the mechanical propertiesspecified in Table 2.5. General Requirements5.1 The following requirements for orders for materialfurnished under this specification shall conform to the appli-cable requ

8、irements of the current edition of SpecificationA 480/A 480M.5.1.1 Definitions,5.1.2 General requirements for delivery,5.1.3 Ordering information,5.1.4 Process,5.1.5 Heat treatment,5.1.6 Special tests,5.1.7 Dimensions and permissible variations,5.1.8 Workmanship, finish, and appearance,5.1.9 Number

9、of tests,5.1.10 Specimen preparation,5.1.11 Retreatment,5.1.12 Inspection,5.1.13 Rejection and rehearing,5.1.14 Material test report,5.1.15 Certification, and5.1.16 Packaging, marking, and loading.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Relate

10、d Alloys and is the direct responsibility of SubcommitteeA01.17 on Flat-Rolled and Wrought Stainless Steel.Current edition approved Sept. 1, 2004. Published September 2004. Originallyapproved in 1935. Last previous edition approved in 1999 as A 167 99.2For referenced ASTM standards, visit the ASTM w

11、ebsite, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Society of Automotive Engineers (SAE), 400 CommonwealthDr., Warrendale, PA 15096-0001.1Copyri

12、ght ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.TABLE 1 Chemical RequirementsAComposition, %UNSDesig-nationBType Car-bonMan-ganesePhos-pho-rusSulfur Silicon Chromium Nickel Molyb-denumOther ElementsS30215 302B 0.15 2.00 0.045 0.030 2.003.00

13、 17.019.0 8.0010.0 . . . N 0.10S30800 308 0.08 2.00 0.045 0.030 0.75 19.021.0 10.012.0 . . . . . .S30900 309 0.20 2.00 0.045 0.030 0.75 22.024.0 12.015.0 . . . . . .S31000 310 0.25 2.00 0.045 0.030 1.50 24.026.0 19.022.0 . . . . . .AMaximum unless range or minimum is indicated.BNew designation estab

14、lished in accordance with Practice E 527 and SAE J 1086.TABLE 2 Mechanical Property RequirementsUNSDesignationATypeTensile Strength, min Yield Strength, minBElongationin 2 in. or50 mm,min, %Hardness, maxCksi MPa ksi MPa Brinell Rockwell BS30215 302B 75 515 30 205 40.0 217 95S30800 308 75 515 30 205

15、40.0 183 88S30900 309 75 515 30 205 40.0 217 95S31000 310 75 515 30 205 40.0 217 95ANew designation established in accordance with Practice E 527 and SAE J 1086.BYield strength shall be determined by the offset method at 0.2 % in accordance with Test Methods and Definitions A 370. Unless otherwise s

16、pecified, an alternativemethod of determining yield strength may be based on a total extension under load of 0.5 %.CEither Brinell or Rockwell B hardness is permissible.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin

17、this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must

18、 be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of ther

19、esponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700,

20、 West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).A 167 99 (2004)2