ASTM A20 A20M-2018 Standard Specification for General Requirements for Steel Plates for Pressure Vessels《压力容器用钢板一般要求的标准规范》.pdf

1、Designation: A20/A20M 17A20/A20M 18Standard Specification forGeneral Requirements for Steel Plates for Pressure Vessels1This standard is issued under the fixed designation A20/A20M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, t

2、he year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This general require

3、ments specification2 covers a group of common requirements that, unless otherwise specified in theapplicable product specification, apply to rolled steel plates for pressure vessels covered by each of the following productspecifications issued by ASTM:Title of Specification ASTM DesignationAPressure

4、 Vessel Plates, Alloy Steel, Nickel A203/A203MPressure Vessel Plates, Alloy Steel, Molybdenum A204/A204MPressure Vessel Plates, Alloy Steel, Manganese-Vanadium-NickelA225/A225MStainless Chromium Steel-Clad Plate A263Stainless Chromium-Nickel Steel-Clad Plate A264Nickel and Nickel-Base Alloy-Clad Ste

5、el Plate A265Pressure Vessel Plates, Carbon Steel, Low- andIntermediate-Tensile StrengthA285/A285MPressure Vessel Plates, Carbon Steel, Manganese-Silicon A299/A299MPressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-NickelA302/A302MPressure Vessel Plates, Alloy Steel,

6、Double-Normalized and Tempered 9 % NickelA353/A353MPressure Vessel Plates, Alloy Steel, Chromium-MolybdenumA387/A387MPressure Vessel Plates, Carbon Steel, High StrengthManganeseA455/A455MPressure Vessel Plates, Carbon Steel, for Intermediate-and Higher-Temperature ServiceA515/A515MPressure Vessel Pl

7、ates, Carbon Steel, Moderate- andLower-Temperature ServiceA516/A516MPressure Vessel Plates, Alloy Steel, High-Strength,Quenched and TemperedA517/A517MPressure Vessel Plates, Alloy Steel, Quenched andTempered, Manganese-Molybdenum and Manganese-Molybdenum-NickelA533/A533M1 This specification is under

8、 the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee A01.11on Steel Plates for Boilers and Pressure Vessels.Current edition approved Nov. 15, 2017March 1, 2018. Published November 2017March 2018. Originally approved in 19

9、50. Last previous edition approved in 20152017as A20/A20M 15.A20/A20M 17. DOI: 10.1520/A0020_A0020M-17.10.1520/A0020_A0020M-18.2 For ASME Boiler and Pressure Vessel Code applications, see related Specification SA-20/SA-20M in Section II of that Code.This document is not an ASTM standard and is inten

10、ded only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the curren

11、t versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1Title of Specification ASTM Desig

12、nationAPressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon SteelA537/A537MPressure Vessel Plates, Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum, and Chromium-Molybdenum-VanadiumA542/A542MPressure Vessel Plates, Alloy Steel, Quenched andTempered Nickel-Chromium-MolybdenumA543/A54

13、3MPressure Vessel Plates, Alloy Steel, Quenched andTempered 7, 8, and 9 % NickelA553/A553MPressure Vessel Plates, Carbon Steel, Manganese-Titanium for Glass or Diffused Metallic CoatingsA562/A562MPressure Vessel Plates, Carbon Steel, High Strength, forModerate and Lower Temperature ServiceA612/A612M

14、Pressure Vessel Plates, 5 % and 512 % Nickel AlloySteels, Specially Heat TreatedA645/A645MPressure Vessel Plates, Carbon-Manganese-SiliconSteel, for Moderate and Lower Temperature ServiceA662/A662MPressure Vessel Plates, Carbon-Manganese-SiliconSteel, Quenched and Tempered, for Welded PressureVessel

15、sA724/A724MPressure Vessel Plates, Low-Carbon Age-HardeningNickel-Copper-Chromium-Molybdenum-Columbium(Niobium) Alloy SteelA736/A736MPressure Vessel Plates, High-Strength Low-Alloy Steel A737/A737MPressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, for Moderate and LowerTemperature

16、 ServiceA738/A738MPressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-VanadiumA832/A832MSteel Plates for Pressure Vessels, Produced byThermo-Mechanical Control Process (TMCP)A841/A841MSteel Plates, 9 % Nickel Alloy, for Pressure Vessels,Produced by the Direct-Quenching ProcessA844/A844MPressure

17、 Vessel Plates, Alloy Steel, Chromium-Molybdenum-TungstenA1017/A1017MA These designations refer to the latest issue of the respective specification which appears in the Annual Book of ASTM Standards, Vol 01.04.1.1.1 This general requirements specification also covers a group of supplementary require

18、ments that are applicable to severalof the above product specifications as indicated therein. Such requirements are provided for use if additional testing or additionalrestrictions are required by the purchaser, and apply only if specified individually in the purchase order.1.2 Appendix X1 provides

19、information on coil as a source of plates for pressure vessels.1.3 Appendix X2 provides information on the variability of tensile properties in plates for pressure vessels.1.4 Appendix X3 provides information on the variability of Charpy-V-Notch impact test properties in plates for pressure vessels.

20、1.5 Appendix X4 provides information on cold bending of plates, including suggested minimum inside radii for cold bending.1.6 These materials are intended to be suitable for fusion welding. When the steel is to be welded, it is presupposed that awelding procedure suitable for the grade of steel and

21、intended use or service will be utilized.1.7 In case of any conflict in requirements, the requirements of the applicable product specification prevail over those of thisgeneral requirements specification.1.8 Additional requirements that are specified in the purchase order and accepted by the supplie

22、r are permitted, provided thatsuch requirements do not negate any of the requirements of this general requirements specification or the applicable productspecification.1.9 For purposes of determining conformance with this general requirements specification and the applicable productspecification, va

23、lues are to be rounded to the nearest unit in the right-hand place of figures used in expressing the limiting valuesin accordance with the rounding method of Practice E29.1.10 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in eac

24、hsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.11 This general requirements specification and the applicable product specification are expressed in both inch

25、-pound units andSI units; unless the order specifies the applicable “M” specification designation (SI units), the plates are to be furnished toinch-pound units.1.12 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the

26、 Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.A20/A20M 1822. Referenced Documents2.1 ASTM Standards:3A203/A203M Specification for Pressure Vessel Plates, Alloy Steel

27、, NickelA204/A204M Specification for Pressure Vessel Plates, Alloy Steel, MolybdenumA225/A225M Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Vanadium-NickelA263 Specification for Stainless Chromium Steel-Clad PlateA264 Specification for Stainless Chromium-Nickel Steel-Clad PlateA2

28、65 Specification for Nickel and Nickel-Base Alloy-Clad Steel PlateA285/A285M Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile StrengthA299/A299M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-SiliconA302/A302M Specification for Pressure Vessel

29、Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-NickelA353/A353M Specification for Pressure Vessel Plates, Alloy Steel, Double-Normalized and Tempered 9 % NickelA370 Test Methods and Definitions for Mechanical Testing of Steel ProductsA387/A387M Specification for Pressure Vessel P

30、lates, Alloy Steel, Chromium-MolybdenumA435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel PlatesA455/A455M Specification for Pressure Vessel Plates, Carbon Steel, High-Strength ManganeseA515/A515M Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and H

31、igher-Temperature ServiceA516/A516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature ServiceA517/A517M Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and TemperedA533/A533M Specification for Pressure Vessel Plates, Alloy Stee

32、l, Quenched and Tempered, Manganese-Molybdenum andManganese-Molybdenum-NickelA537/A537M Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon SteelA542/A542M Specification for Pressure Vessel Plates, Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum, andChromium-Moly

33、bdenum-VanadiumA543/A543M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered Nickel-Chromium-MolybdenumA553/A553M Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 7, 8, and 9 % NickelA562/A562M Specification for Pressure Vessel Plates, Carbon Ste

34、el, Manganese-Titanium for Glass or Diffused MetallicCoatingsA577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel PlatesA578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special ApplicationsA612/A612M Specification for Pressure Vessel Pla

35、tes, Carbon Steel, High Strength, for Moderate and Lower TemperatureServiceA645/A645M Specification for Pressure Vessel Plates, 5 % and 512 % Nickel Alloy Steels, Specially Heat TreatedA662/A662M Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, for Moderate and Lower Tempera

36、tureServiceA700 Guide for Packaging, Marking, and Loading Methods for Steel Products for ShipmentA724/A724M Specification for Pressure Vessel Plates, Carbon-Manganese-Silicon Steel, Quenched and Tempered, for WeldedPressure VesselsA736/A736M Specification for Pressure Vessel Plates, Low-Carbon Age-H

37、ardening Nickel-Copper-Chromium-Molybdenum-Columbium (Niobium) Alloy SteelA737/A737M Specification for Pressure Vessel Plates, High-Strength, Low-Alloy SteelA738/A738M Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel, for Moderate and LowerTemperature ServiceA75

38、1 Test Methods, Practices, and Terminology for Chemical Analysis of Steel ProductsA770/A770M Specification for Through-Thickness Tension Testing of Steel Plates for Special ApplicationsA832/A832M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-VanadiumA841/A841M Specificat

39、ion for Steel Plates for Pressure Vessels, Produced by Thermo-Mechanical Control Process (TMCP)A844/A844M Specification for Steel Plates, 9 % NickelAlloy, for Pressure Vessels, Produced by the Direct-Quenching ProcessA941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloy

40、sA1017/A1017M Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-TungstenE21 Test Methods for Elevated Temperature Tension Tests of Metallic MaterialsE29 Practice for Using Significant Digits in Test Data to Determine Conformance with SpecificationsE112 Test Methods for Deter

41、mining Average Grain SizeE208 Test Method for Conducting Drop-Weight Test to Determine Nil-Ductility Transition Temperature of Ferritic Steels3 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolu

42、me information, refer to the standards Document Summary page on the ASTM website.A20/A20M 183E709 Guide for Magnetic Particle Testing2.2 American Society of Mechanical Engineers Code:4ASME Boiler and Pressure Vessel Code, Section IX2.3 U.S. Federal Standard:5Fed. Std. No. 123 Marking for Shipment (C

43、ivil Agencies)2.4 Automotive Industry Action Group Standard:6B 1 Bar Code Symbology Standard3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 as-rolledfor plates, the condition of a plate that has been hot-rolled and will not be or has not yet been heat treated.3.1.1.1 Discussio

44、nThe term as-rolled by itself is not meant to refer to plates that have been hot-rolled using control- rolling (CR), direct quench(DQT), thermo-mechanical control rolling (TMCP), recrystalization control rolling (RCR), or any similar methods that areintended to produce a set of properties that are n

45、ot normally achievable were they not employed. The term as-rolled is to bedistinguished from the established term plate-as-rolled that does not define the actual condition of a plate, but defines the singularproduct of a slab or ingot that has been hot-rolled3.1.2 coilhot-rolled steel in coil form f

46、or processing into finished plates.3.1.3 exclusivewhen used in relation to ranges, as for ranges of thicknesses in the tables of permissible variations indimensions, the term is intended to exclude only the greater value of the range. Thus, a range from 60 to 72 in. 1500 to 1800 mmexclusive includes

47、 60 in. 1500 mm, but does not include 72 in. 1800 mm.3.1.4 heat treatment termssee 3.1.83.1.10, and Terminology A941.3.1.5 hot forminga forming operation producing permanent deformation, performed after the plate has been heated to thetemperature required to produce grain refinement.3.1.6 hot-rolled

48、 (hot rolling)for plates, the process described for a plate that has been rolled from a slab or ingot whosestarting temperature is suitably above the recrystallization temperature of the metal to be rolled.3.1.6.1 DiscussionHot-rolled may be used in conjunction with any rolling process to more effec

49、tively describe a specific condition, for example;hot-rolled as-rolled; hot-rolled control-rolled, etc.3.1.7 manufacturerthe organization that directly controls the conversion of steel ingots or slabs, by hot rolling, intoplate-as-rolled or into coil; and for plates produced from plate-as-rolled, the organization that directly controls, or is responsiblefor, one or more of the operations involved in finishing the plates. Such finishing operations include leveling, cutting to length,testing, inspection, conditioning, heat treatment (if applicable), packaging, m