ASTM A214 A214M-1996(2012) Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes《热交换器和冷凝器用电阻焊接碳钢管的标准规格》.pdf

1、Designation: A214/A214M 96 (Reapproved 2012)Standard Specification forElectric-Resistance-Welded Carbon Steel Heat-Exchangerand Condenser Tubes1This standard is issued under the fixed designation A214/A214M; the number immediately following the designation indicates the yearof original adoption or,

2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1

3、This specification2covers minimum-wall-thickness,electric-resistance-welded, carbon steel tubes to be used forheat exchangers, condensers, and similar heat-transfer appara-tus.1.2 The tubing sizes usually furnished to this specificationare to 3 in. 76.2 mm in outside diameter, inclusive. Tubinghavin

4、g other dimensions may be furnished, provided suchtubes comply with all other requirements of this specification.1.3 Mechanical property requirements do not apply totubing smaller than18 in. 3.2 mm in inside diameter or 0.015in. 0.4 mm in thickness.1.4 The purchaser shall specify in the order the ou

5、tsidediameter and minimum wall thickness. The inside diametershall not be specified.1.5 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem are not exact equivalents; th

6、erefore, each system mustbe used independently of the other. Combining values from thetwo systems may result in nonconformance with the specifi-cation. The inch-pound units shall apply unless the “M”designation of this specification is specified in the order.2. Referenced Documents2.1 ASTM Standards

7、:3A450/A450M Specification for General Requirements forCarbon and Low Alloy Steel Tubes3. Ordering Information3.1 Orders for material under this specification shouldinclude the following, as required, to describe the desiredmaterial adequately:3.1.1 Quantity (feet, metres, or number of lengths),3.1.

8、2 Name of material (electric-resistance-welded tubes),3.1.3 Size (outside diameter and minimum wall thickness),3.1.4 Length (specific or random),3.1.5 Optional requirements (Section 8 and 10.5),3.1.6 Test report required (see Certification Section ofSpecification A450/A450M),3.1.7 Specification desi

9、gnation, and3.1.8 Special requirements.4. General Requirements4.1 Material furnished under this specification shall con-form to the applicable requirements of the current edition ofSpecification A450/A450M, unless otherwise provided herein.5. Manufacture5.1 Tubes shall be made by electric-resistance

10、 welding.6. Heat Treatment6.1 After welding, all tubes shall be heat treated at atemperature of 1650F 900C or higher and followed bycooling in air or in the cooling chamber of a controlledatmosphere furnace. Cold drawn tubes shall be heat treatedafter the final cold-draw pass at a temperature of 120

11、0F650C or higher.7. Chemical Composition7.1 The steel shall conform to the following requirements asto chemical composition:Carbon, max % 0.18Manganese, % 0.27 to 0.63Phosphorus, max, % 0.035Sulfur, max, % 0.0357.2 Supplying an alloy grade of steel that specificallyrequires the addition of any eleme

12、nt other than those listed in7.1 is not permitted.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.09 on Carbon Steel Tubular Products.Current edition approved March 1, 2012. Published

13、November 2012. Originallyapproved in 1939. Last previous edition approved in 2005 as A214/A214M 96(2005). DOI: 10.1520/A0214_A0214M-96R12.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-214 in Section II of that Code.3For referenced ASTM standards, visit the ASTM

14、 website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United

15、States18. Product Analysis8.1 When requested on the purchase order, a product analy-sis shall be made by the supplier from 1 tube per 250 pieces;when tubes are identified by heat, one tube per heat shall beanalyzed. The chemical composition thus determined shallconform to the requirements specified.

16、8.2 If the original test for product analysis fails, retests oftwo additional lengths of flat-rolled stock, or tubes shall bemade. Both retests, for the elements in question, shall meet therequirements of the specification; otherwise all remainingmaterial in the heat or lot (Note 1) shall be rejecte

17、d or, at theoption of the producer, each length of flat-rolled stock or tubemay be individually tested for acceptance. Lengths of flat-rolled stock or tubes which do not meet the requirements of thespecification shall be rejected.NOTE 1A lot consists of 250 tubes.9. Hardness Requirements9.1 The tube

18、s shall have a hardness number not exceeding72 HRB.10. Mechanical Tests Required10.1 Flattening TestOne flattening test shall be made onspecimens from each of two tubes from each lot (Note 1)orfraction thereof.10.2 Flange TestOne flange test shall be made on speci-mens from each of two tubes from ea

19、ch lot (Note 1) or fractionthereof.10.3 Reverse Flattening TestOne reverse flattening testshall be made on a specimen from each 1500 ft 450 m offinished tubing.10.4 Hardness TestBrinell or Rockwell hardness testsshall be made on specimens from two tubes from each lot. Theterm lot applies to all tube

20、s prior to cutting, of the samenominal diameter and wall thickness which are produced fromthe same heat of steel. When final heat treatment is in abatch-type furnace, a lot shall include only those tubes of thesame size and the same heat which are heat treated in the samefurnace charge. When final h

21、eat treatment is in a continuousfurnace, a lot shall include all tubes of the same size and heat,heat treated in the same furnace at the same temperature, timeat heat, and furnace speed.10.5 Hydrostatic or Nondestructive Electric TestEachtube shall be subjected to either the hydrostatic or the nonde

22、-structive electric test. The purchaser may specify which test isto be used.11. Surface Condition11.1 The finished tubes shall be free of scale. A slightamount of oxidation shall not be considered as scale.12. Product Marking12.1 In addition to the marking prescribed in SpecificationA450/A450M, the

23、letters “ERW” shall be legibly stenciled oneach tube, or marked on a tag attached to the bundle or box inwhich the tubes are shipped.12.2 The manufacturers name or symbol may be placedpermanently on each tube by rolling or light stamping beforenormalizing. If a single stamp is placed on the tube by

24、hand,this mark should not be less than 8 in. 200 mm from one endof the tube.12.3 Bar CodingIn addition to the requirements in 12.1and 12.2 bar coding is acceptable as a supplemental identifi-cation method. The purchaser may specify in the order aspecific bar coding system to be used.ASTM Internation

25、al takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their

26、own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be

27、addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,

28、 at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A214/A214M 96 (2012)2