ASTM A265-2009 Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate《镍和镍基合金涂层钢板用标准规范》.pdf

1、Designation: A 265 09Standard Specification forNickel and Nickel-Base Alloy-Clad Steel Plate1This standard is issued under the fixed designation A 265; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A nu

2、mber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification2covers plate of a carbon steel orlow

3、-alloy steel base to which is integrally and continuouslybonded on one or both sides a layer of nickel or nickel-basealloy. The material is generally intended for pressure vessel usebut may be used in other structural applications where corro-sion resistance of the alloy is of prime importance.1.2 T

4、he values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:3A 6/A 6M Specification for General Requirements

5、 forRolled Structural Steel Bars, Plates, Shapes, and SheetPilingA 20/A 20M Specification for General Requirements forSteel Plates for Pressure VesselsA 370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA 578/A 578M Specification for Straight-Beam UltrasonicExamination of Rolle

6、d Steel Plates for Special Applica-tionsA 751 Test Methods, Practices, and Terminology forChemical Analysis of Steel ProductsB 127 Specification for Nickel-Copper Alloy (UNSN04400) Plate, Sheet, and StripB 162 Specification for Nickel Plate, Sheet, and StripB 168 Specification for Nickel-Chromium-Ir

7、on Alloys(UNS N06600, N06601, N06603, N06690, N06693,N06025, N06045, and N06696) and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Plate, Sheet,and StripB 333 Specification for Nickel-Molybdenum Alloy Plate,Sheet, and StripB 409 Specification for Nickel-Iron-Chromium Alloy Plate,Sheet, and St

8、ripB 424 Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNSN08825 and UNS N08221)* Plate, Sheet, and StripB 443 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNSN06625) and Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219)* Plate, Sheet,and StripB 463 Specification for UNS N08020, UNS N

9、08026, andUNS N08024 Alloy Plate, Sheet, and StripB 575 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, Low-Carbon Nickel-Chromium-Molybdenum-Tantalum, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Plate, Sheet, andStripB 582 Specific

10、ation for Nickel-Chromium-Iron-Molybdenum-Copper Alloy Plate, Sheet, and StripB 625 Specification for UNS N08925, UNS N08031, UNSN08932, UNS N08926, UNS N08354, and UNS R20033Plate, Sheet, and Strip2.2 Other Standards:ASME Code Boiler and Pressure Vessel Code, Section IX,Welding Qualifications43. Te

11、rminology3.1 Definitions of Terms Specific to This Standard:3.1.1 This material is considered as single-clad or double-clad nickel or nickel-base alloy clad steel plate, depending onwhether one or both sides are covered.3.1.2 The term plate as used in this specification applies tomaterial316 in. (2.

12、73 mm) and over in thickness, and over 10in. (254 mm) in width.1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.11 on Steel Plates for Boilers and Pressure Vessels.Current edition appro

13、ved May 1, 2009. Published June 2009. Originallyapproved in 1943. Last previous edition approved in 2003 as A 265 03.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-265 in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.or

14、g, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.4Available from American Society of Mechanical Engineers (ASME), ASMEInternational Headquarters, Three Park Ave., New York, NY 1

15、0016-5990, http:/www.asme.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.3 alloy claddingthe nickel or nickel-base alloy com-ponent of the composite plate.3.1

16、.4 base metal (backing steel)component to which thealloy cladding is applied, usually the greater percentage of thecomposite plate and usually consisting of carbon or low-alloysteel.3.1.5 integrally and continuously bondedthe process bywhich the alloy cladding and base metal are brought together tof

17、orm a metallurgical bond at essentially the entire interface ofthe two metals by means other than those processes that do notproduce a homogeneous composite plate.4. Ordering Information4.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for material ordered u

18、nder thisspecification. Such requirements may include, but are notlimited to the following:4.1.1 Quantity (weight or number of pieces).4.1.2 Heat treatment, if required (see Section 5).4.1.3 Dimensions, including the thickness of the claddingalloy and the backing steel, or of the total composite pla

19、te andif more or less restrictive thickness tolerances apply.4.1.4 Cladding alloy specification (see Section 6).4.1.5 Base metal specification (see Section 6).4.1.6 Product analysis, if required. Specify whether appli-cable to the cladding alloy, backing steel, or both (see Section10).4.1.7 Mechanic

20、al Properties (see Sections 7, 13, and 14).4.1.8 Restrictions, if required, on repair by welding (seeSection 14).4.1.9 Additions to the specification or special requirements.4.1.10 Corrosions tests, if required.4.2 In addition to the basic requirements of this specificationand the backing steel spec

21、ification, certain supplementaryrequirements are available when necessary to meet the end userequirements. These include:4.2.1 Nondestructive examination,4.2.2 Impact testing, and4.2.3 Simulated Post-Weld Heat Treatment of MechanicalTest Coupons (SPWHT).4.3 The purchaser is referred to the listed su

22、pplementaryrequirements in this specification and to the detailed require-ments in Specification A 20/A 20M. If the requirements of thisspecification are in conflict with the requirements of Specifi-cation A 20/A 20M, the requirements of this specification shallprevail.4.4 Special tests.5. Materials

23、 and Manufacture5.1 Process:5.1.1 The steel shall be made by the open-hearth, electric-furnace (with separate degassing and refining optional), orbasic-oxygen processes, or by secondary processes wherebysteel made from these primary processes is remelted using, butnot limited to electroslag remeltin

24、g or vacuum arc remeltingprocesses.5.1.2 The cladding metal may be metallurgically bonded tothe base metal by any method that will produce a clad steel thatwill conform to the requirements of this specification.5.2 Heat TreatmentUnless a specific heat treatment isrequired by the cladding material or

25、 base steel specification, orunless otherwise agreed upon by the purchaser and manufac-turer, the clad plate shall be furnished in a condition that isappropriate for the cladding alloy, base metal, or both.6. Chemical Composition6.1 The composite plate may conform to any desired com-bination claddin

26、g metal and base metal as described in 6.2 and6.3, and as agreed upon between the purchaser and themanufacturer.6.2 Cladding MetalThe nickel or nickel-base alloy clad-ding metal specified shall conform to the requirements as tochemical composition prescribed for the respective metal inSpecifications

27、 B 127, B 162, B 168, B 333, B 409, B 424,B 443, B 463, B 575, B 582, and B 625, or other nickel-basealloy as agreed upon by the purchaser and manufacturer.6.3 Base MetalThe base metal shall be carbon steel orlow-alloy steel conforming to the ASTM specifications forsteels for either pressure vessels

28、 or general structural applica-tions, or other, as agreed upon by the purchaser and manufac-turer. The base metal shall conform to the chemical require-ments of the specification to which it is ordered.7. Mechanical Properties7.1 Tensile Requirements:7.1.1 The tensile properties shall be determined

29、by a tensiontest of the composite plate for clad plates that meet all of thefollowing conditions.(1) The nominal composite gage is less than or equal to 112in (38 mm).(2) The specified minimum tensile strength of the base steelis less than or equal to 70 000 psi (485 MPa).(3) The specified minimum y

30、ield strength of the base steelis less than or equal to 40 000 psi (275 MPa).(4) The tensile properties thus determined shall not be lessthan the minimum and not more than 5000 psi (35 MPa) overthe maximum prescribed in the specification for the base steelused. All other tensile test requirements of

31、 the specification forthe base steel shall be met.7.1.2 The tensile properties shall be determined by atension test of the base steel only for clad plates that meet oneof the following conditions. The properties thus determinedshall meet all of the tensile test requirements for the base steel.(1) Th

32、e composite gage is greater than 112 in. (38 mm).(2) The specified minimum tensile strength of the base steelis greater than 70 000 psi (485 MPa).TABLE 1 Weights for Component MaterialsDensityWeight per SquareFoot for Material1 in. (25.4 mm)in Thickness, lblb/in.3g/cm3Steel 0.283 7.83 40.80Nickel 0.

33、321 8.88 46.22Nickel-copper alloy 0.319 8.83 45.94Nickel-chromium-ironalloy0.307 8.49 44.21A265092(3) The specified minimum yield strength of the base steelis greater than 40 000 psi (275 MPa).7.1.3 If the cladding is for corrosion allowance only, thecladding need not be included in the tensile test

34、. The tensileproperties thus determined shall meet the base steel require-ments.7.2 Test for strength of the bond, when required, must bespecified by the purchaser and shall consist of one of thefollowing.7.2.1 Shear StrengthWhen required by the purchaser, theminimum shear strength of the alloy clad

35、ding and base metalsshall be 20 000 psi (140 MPa). The shear test, when specified,shall be made in the manner indicated in Fig. 1. The minimumcladding thickness for shear testing shall be 0.075 in. (1.9 mm)exclusive as ordered. Testing for shear strength for clad plateswith minimum cladding thicknes

36、s of 0.075 in (1.9 mm) or lessshall be permitted upon agreement between the purchaser andthe manufacturer.7.2.2 Bond StrengthAs an alternative to the shear strengthtest provided in 7.2.1 or when agreed upon by the purchaserand the manufacturer, or both, three bend tests shall be madewith the alloy c

37、ladding in compression to determine the qualityof the bond. These bend tests shall be made in the manner ofthe tension tests indicated in Fig. 2 and shall be bent through anangle of 180 to the bend diameters provided for in eitherSpecification A 6/A 6M or Specification A 20/A 20M (Appen-dix X4, or e

38、quivalent), as applicable. At least two of the threetests shall show not more than 50 % separation on both edgesof the bent portion. Greater separation shall be cause forrejection.7.3 Methods and practices relating to mechanical testingrequired by this specification shall be in accordance with theTe

39、st Methods and Definitions of A 370.8. Number of Tests and Retests8.1 One or more tension tests, as required by the specifica-tions for the base metal and when specified, one shear test orthree bond bend tests shall be made, representing each plate asrolled. Each specimen shall be in the final condi

40、tion of heattreatment required for the plate, including any SPWHT ifrequired.8.2 If any test specimen shows defective machining ordevelops flaws, it may be discarded and another specimensubstituted.9. Test Specimens9.1 The tension test specimens shall conform to the require-ments prescribed in the s

41、pecifications for the base metal.9.2 Bend test specimens for the alternative bond strengthtests shall be taken at right angles to its longitudinal axis.9.3 When required by the purchaser, the shear test specimenshall be taken near a top or bottom corner of the plate as rolled,parallel to its longitu

42、dinal axis, or other location that isrepresentative of the final product.9.4 For plates 112 in. (38 mm) and under in thickness,tension test specimens shall be the full thickness of thematerial, except as specified in 7.1.2 and 7.1.3.9.5 For plates over 112 in. (38 mm) in thickness, tensiontests shal

43、l be of the form shown in Fig. 3 and shall be of allbase steel conforming to the requirements of the specificationfor the base steel.9.6 The bend test specimen used for bond strength determi-nation shall be 112 in. (38 mm) by not more than34 in. (19 mm)in thickness and shall be machined to the form

44、and dimensionsshown in Fig. 2, or may be machined with both edges parallel.In reducing the thickness of the specimen, both the alloyMetric Equivalentsin. mm in. mm0.005 0.127 1 25.418 3.17 212 64.534 19.1 3 76.2FIG. 1 Test Specimen and Method of Making Shear Test of CladPlateMetric Equivalentsin. mm

45、 in. mm0.01 0.254 112 38.118 3.17 2 50.814 6.35 3 76.21 25.4 8 203.2NOTE 1When necessary, it is permissible to use a narrower specimen,but in such a case the reduced portion shall be not less than 1 in. in width.NOTE 2Punch marks for measuring elongation after fracture shall bemade on the flat or on

46、 the edge of the specimen and within the parallelsection; either a set of nine punch marks 1 in. apart, or one or more setsof 8-in. punch marks may be used.NOTE 3The dimension t is the thickness of the test specimen asprovided for in the applicable material specifications.FIG. 2 Standard Rectangular

47、 Test Specimens with 8-in. GageLengthA265093cladding and the base steel shall be machined so as to maintainthe same ratio of clad metal to base steel as is maintained in theplate, except that the thickness of the clad material need not bereduced below18 in. (3.1 mm). The sides of the bend testspecim

48、en used for bond strength determination may have thecorners rounded to a radius not over116 in. (1.6 mm) for plates,2 in. (50 mm) and under in thickness, and not over18 in. (3.1mm) for plates over 2 in. (50 mm) in thickness.10. Product Analysis10.1 Product analysis may be required for the cladding a

49、lloyon finished product. Chemical analysis may be accomplishedby wet chemical or instrumental procedures. If wet chemicalprocedures are used, millings may be taken only when thecomposite plate thickness is sufficient to permit obtainingmillings without danger of contamination from the adjacentlayer. If spectrometric procedures are used, the sample shall beexposed on the center line of the cladding when there issufficient cladding thickness available so that there is nocontamination from the adjacent base metal.10.2 If product analysis is specified by the