ASTM A29 A29M-2012e1 Standard Specification for General Requirements for Steel Bars Carbon and Alloy Hot-Wrought《热锻碳合金钢筋通用要求的标准规格》.pdf

1、Designation: A29/A29M 121Standard Specification forGeneral Requirements for Steel Bars, Carbon and Alloy,Hot-Wrought1This standard is issued under the fixed designation A29/A29M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the

2、year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1NOTETitle was editorially revised i

3、n December 2013.1. Scope*1.1 This specification2covers a group of common require-ments which, unless otherwise specified in the purchase orderor in an individual specification, shall apply to carbon and alloysteel bars under each of the following ASTM specifications (orunder any other ASTM specifica

4、tion which invokes thisspecification or portions thereof):Title of Specification ASTMDesignationAHot-Rolled Carbon Steel Bars:Steel Bars, Carbon, Quenched and Tempered A321Steel Bars and Shapes, Carbon Rolled from “T Rails A499Steel Bars, Carbon, Merchant Quality, M-Grades A575Steel Bars, Carbon, Ho

5、t-Wrought, Special Quality A576Steel Bars, Carbon, Merchant Quality, MechanicalPropertiesA663/A663MSteel Bars, Carbon, Hot-Wrought, Special Quality, Me-chanical PropertiesA675/A675MSteel Bars for Springs, Carbon and Alloy A689Cold-Finished Carbon Steel Bars:Steel Bars, Carbon and Alloy, Cold-Finishe

6、d A108Cold-Drawn Stress-Relieved Carbon Steel Bars Sub-ject to Mechanical Property RequirementsA311/A311MHot-Rolled Alloy Steel Bars:Steel Bars, Alloy, Standard Grades A322Carbon and Alloy Steel Bars Subject to End-QuenchHardenability RequirementsA304Steel Bars, Alloy, Hot-Wrought or Cold-Finished,Q

7、uenched and TemperedA434Steel Bars, Alloy, Hot-Wrought, for Elevated Tempera-ture or Pressure-Containing Parts, or BothA739Cold-Finished Alloy Steel Bars:Steel Bars, Alloy, Hot-Rolled or Cold-Finished,Quenched and TemperedA434Steel Bars, Carbon, Hot-Wrought or Cold-Finished,Special Quality, for Pres

8、sure Piping ComponentsA696AThese designations refer to the latest issue of the respective specifications,which appear either in the Annual Book of ASTM Standards, Vol 01.05, or asreprints obtainable from ASTM.1.2 In case of any conflict in requirements, the requirementsof the purchase order, the ind

9、ividual material specification, andthis general specification shall prevail in the sequence named.1.3 The values stated in inch-pound units or SI units are tobe regarded as the standard. Within the text, the SI units areshown in brackets. The values stated in each system are notexact equivalents; th

10、erefore, each system must be used inde-pendently of the other. Combining values from the two systemsmay result in nonconformance with the specification.1.4 For purposes of determining conformance to this speci-fication and the various material specifications referenced in1.1, dimensional values shal

11、l be rounded to the nearest unit inthe right-hand place of figures used in expressing the limitingvalues in accordance with the rounding method of PracticeE29.NOTE 1Specification A29 previously listed dimensional tolerances forcold-finished bars; these are now found in Specification A108.2. Referenc

12、ed Documents2.1 ASTM Standards:3A108 Specification for Steel Bar, Carbon and Alloy, Cold-FinishedA304 Specification for Carbon and Alloy Steel Bars Subjectto End-Quench Hardenability RequirementsA311/A311M Specification for Cold-Drawn, Stress-Relieved Carbon Steel Bars Subject to Mechanical Prop-ert

13、y RequirementsA321 Specification for Steel Bars, Carbon, Quenched and1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.15 on Bars.Current edition approved May 1, 2012. Published May 2012

14、. Originallyapproved in 1957. Last previous edition approved in 2011 as A29/A29M 11a.DOI: 10.1520/A0029_A0029M-12E01.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-29/SA-29M in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.a

15、stm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO B

16、ox C700, West Conshohocken, PA 19428-2959. United States1Tempered (Withdrawn 2007)4A322 Specification for Steel Bars, Alloy, Standard GradesA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA434 Specification for Steel Bars, Alloy, Hot-Wrought orCold-Finished, Quenched and Tem

17、peredA499 Specification for Steel Bars and Shapes, CarbonRolled from “T” RailsA575 Specification for Steel Bars, Carbon, MerchantQuality, M-GradesA576 Specification for Steel Bars, Carbon, Hot-Wrought,Special QualityA663/A663M Specification for Steel Bars, Carbon, Mer-chant Quality, Mechanical Prope

18、rtiesA675/A675M Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical PropertiesA689 Specification for Carbon and Alloy Steel Bars forSpringsA696 Specification for Steel Bars, Carbon, Hot-Wrought orCold-Finished, Special Quality, for Pressure Piping Com-ponentsA700 Practices

19、 for Packaging, Marking, and Loading Meth-ods for Steel Products for ShipmentA739 Specification for Steel Bars, Alloy, Hot-Wrought, forElevated Temperature or Pressure-Containing Parts, orBothA751 Test Methods, Practices, and Terminology for Chemi-cal Analysis of Steel ProductsE29 Practice for Using

20、 Significant Digits in Test Data toDetermine Conformance with SpecificationsE112 Test Methods for Determining Average Grain Size2.2 Federal Standards:5Fed. Std. No. 123 Marking for Shipment (Civil Agencies)Fed. Std. No. 183 Continuous Identification Marking of Ironand Steel Products2.3 Military Stan

21、dard:5MIL-STD-163 Steel Mill ProductsPreparation for Ship-ment and Storage2.4 Other Standards:AIAG B-1 Bar Code Symbology Standard for 3-of-9 BarCodes6AIAG B-5 02.00 Primary Metals Tag Application Standard63. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 Hot-Wrought Steel BarsS

22、teel bars produced by hotforming ingots, blooms, billets, or other semifinished forms toyield straight lengths (or coils, depending upon size, section,and mill equipment) in sections that are uniform throughouttheir length, and in the following sections and sizes:3.1.1.1 Rounds732 to 10.0 in. 5.5 to

23、 250 mm, inclusive,3.1.1.2 Squares732 to 6.0 in. 6 to 160 mm, inclusive,3.1.1.3 Round-Cornered Squares732 to 8.0 in. 6 to 200mm, inclusive,3.1.1.4 Flats14 to 8 in. inclusive, in width:1364 in. inminimum thickness up to 6 in. in width; and 0.230 in. inminimum thickness for over 6 to 8 in. in width, i

24、nclusive over5 mm in thickness up to 150 mm in width; and over 6 mm inthickness for over 150 mm through 200 mm in width.Maximum thickness for all widths is 4 in. 100 mm.3.1.1.5 Hexagons and Octagons14 to 4116 in. 6 to 103mm, inclusive, between parallel surfaces,3.1.1.6 Bar Size ShapesAngles, channel

25、s, tees, zees, whentheir greatest cross-sectional dimension is under 3 in. 75 mm,and3.1.1.7 Special Bar SectionsHalf-rounds, ovals, half-ovals, other special bar size sections.3.1.2 Cold-Finished Steel BarsSteel bars produced bycold finishing previously hot-wrought bars by means of colddrawing, cold

26、 forming, turning, grinding, or polishing (singlyor in combination) to yield straight lengths or coils in sectionsthat are uniform throughout their length and in the followingsections and sizes:3.1.2.1 Rounds9 in. 230 mm and under in diameter,3.1.2.2 Squares6 in. 150 mm and under between parallelsur

27、faces,3.1.2.3 Hexagons4 in. 100 mm and under betweenparallel surfaces,3.1.2.4 Flats18 in. 3 mm and over in thickness and notover 12 in. 300 mm in width, and3.1.2.5 Special Bar Sections.3.1.3 LotUnless otherwise specified in the contract ororder, a lot shall consist of all bars submitted for inspecti

28、on atthe same time of the same heat, condition, finish, size, or shape.For bars specified in the quenched and tempered condition,when heat treated in batch-type furnaces, a lot shall consist ofall bars from the same heat, of the same prior condition, thesame size, and subjected to the same heat trea

29、tment in onetempering charge. For bars specified in the quenched andtempered condition, when heat treated without interruption in acontinuous-type furnace, a lot shall consist of all bars from thesame heat, of the same prior condition, of the same size, andsubjected to the same heat treatment.4. Che

30、mical Composition4.1 Limits:4.1.1 The chemical composition shall conform to the re-quirements specified in the purchase order or the individualproduct specifications. For convenience the grades commonlyspecified for carbon steel bars are shown in Tables 1 and 2.Bars may be ordered to these grade des

31、ignations and when soordered shall conform to the specified limits by heat analysis.4.1.2 When compositions other than those shown in Tables1 and 2 are required, the composition limits shall be prepared4The last approved version of this historical standard is referenced onwww.astm.org.5Copies of mil

32、itary specifications, military standards, and federal standardsrequired by contractors in connection with specific procurement functions should beobtained from the procuring activity or as directed by the contracting officer, or fromthe Standardization Documents Order Desk, Bldg. 4 Section D, 700 Ro

33、bbins Ave.,Philadelphia, PA 19111-5094, Attn: NPODS.6Available from Automotive Industry Action Group, North Park Plaza, Ste. 830,17117 W. Nine Mile Rd., Southfield, MI 48075.A29/A29M 1212TABLE 1 Grade Designations and Chemical Compositions of Carbon Steel BarsGrade DesignationHeat Chemical Ranges an

34、d Limits, %Carbon Manganese Phosphorus, max Sulfur, maxANonresulfurized Carbon SteelsB,C, D,E,F1005 0.06 max 0.35 max 0.040 0.0501006 0.08 max 0.250.40 0.040 0.0501008 0.10 max 0.300.50 0.040 0.0501010 0.080.13 0.300.60 0.040 0.0501011 0.080.13 0.600.90 0.040 0.0501012 0.100.15 0.300.60 0.040 0.0501

35、013 0.110.16 0.500.80 0.040 0.0501015 0.130.18 0.300.60 0.040 0.0501016 0.130.18 0.600.90 0.040 0.0501017 0.150.20 0.300.60 0.040 0.0501018 0.150.20 0.600.90 0.040 0.0501019 0.150.20 0.701.00 0.040 0.0501020 0.180.23 0.300.60 0.040 0.0501021 0.180.23 0.600.90 0.040 0.0501022 0.180.23 0.701.00 0.040

36、0.0501023 0.200.25 0.300.60 0.040 0.0501025 0.220.28 0.300.60 0.040 0.0501026 0.220.28 0.600.90 0.040 0.0501029 0.250.31 0.600.90 0.040 0.0501030 0.280.34 0.600.90 0.040 0.0501034 0.320.38 0.500.80 0.040 0.0501035 0.320.38 0.600.90 0.040 0.0501037 0.320.38 0.701.00 0.040 0.0501038 0.350.42 0.600.90

37、0.040 0.0501039 0.370.44 0.701.00 0.040 0.0501040 0.370.44 0.600.90 0.040 0.0501042 0.400.47 0.600.90 0.040 0.0501043 0.400.47 0.701.00 0.040 0.0501044 0.430.50 0.300.60 0.040 0.0501045 0.430.50 0.600.90 0.040 0.0501046 0.430.50 0.701.00 0.040 0.0501049 0.460.53 0.600.90 0.040 0.0501050 0.480.55 0.6

38、00.90 0.040 0.0501053 0.480.55 0.701.00 0.040 0.0501055 0.500.60 0.600.90 0.040 0.0501059 0.550.65 0.500.80 0.040 0.0501060 0.550.65 0.600.90 0.040 0.0501064 0.600.70 0.500.80 0.040 0.0501065 0.600.70 0.600.90 0.040 0.0501069 0.650.75 0.400.70 0.040 0.0501070 0.650.75 0.600.90 0.040 0.0501071 0.650.

39、70 0.751.05 0.040 0.0501074 0.700.80 0.500.80 0.040 0.0501075 0.700.80 0.400.70 0.040 0.0501078 0.720.85 0.300.60 0.040 0.0501080 0.750.88 0.600.90 0.040 0.0501084 0.800.93 0.600.90 0.040 0.0501086 0.800.93 0.300.50 0.040 0.0501090 0.850.98 0.600.90 0.040 0.0501095 0.901.03 0.300.50 0.040 0.050Resul

40、furized Carbon SteelsB,D,F1108 0.080.13 0.600.80 0.040 0.080.131109 0.080.13 0.600.90 0.040 0.080.131110 0.080.13 0.300.60 0.040 0.080.131116 0.140.20 1.101.40 0.040 0.160.231117 0.140.20 1.001.30 0.040 0.080.131118 0.140.20 1.301.60 0.040 0.080.131119 0.140.20 1.001.30 0.040 0.240.331132 0.270.34 1

41、.351.65 0.040 0.080.131137 0.320.39 1.351.65 0.040 0.080.131139 0.350.43 1.351.65 0.040 0.130.201140 0.370.44 0.701.00 0.040 0.080.131141 0.370.45 1.351.65 0.040 0.080.131144 0.400.48 1.351.65 0.040 0.240.331145 0.420.49 0.701.00 0.040 0.040.071146 0.420.49 0.701.00 0.040 0.080.131151 0.480.55 0.701

42、.00 0.040 0.080.13Rephosphorized and Resulfurized Carbon SteelsD,FGrade Designation Carbon Manganese Phosphorous Sulfur Lead1211 0.13 max 0.600.90 0.070.12 0.100.15 .1212 0.13 max 0.701.00 0.070.12 0.160.23 .A29/A29M 1213using the ranges and limits shown in Table 3 for carbon steeland Table 4 for al

43、loy steel.4.2 Heat or Cast Analysis:4.2.1 The chemical composition of each heat or cast shall bedetermined by the manufacturer in accordance with TestMethods, Practices, and Terminology A751.4.2.2 The heat or cast analysis shall conform to the require-ments specified in the product specification or

44、purchase order.These can be the heat chemical range and limit for a gradedesignated in Tables 1 and 2, or another range and limit inaccordance with 4.1.2, or with requirements of the productspecification.NOTE 2Heat analysis for lead is not determinable since lead is addedto the ladle stream while ea

45、ch ingot is poured. When specified as an addedelement to a standard steel, the percentage of lead is reported as 0.15 to0.35 incl, which is the range commonly specified for this element.4.2.3 If requested or required, the heat analysis shall bereported to the purchaser or his representative.4.2.4 Re

46、porting of significant figures and rounding shall bein accordance with Test Methods, Practices, and TerminologyA751.4.3 Product Analysis:4.3.1 Merchant quality carbon bar steel is not subject torejection for product analysis unless misapplication of a heat isclearly indicated.4.3.2 Analyses may be m

47、ade by the purchaser from finishedbars other than merchant quality representing each heat ofopen-hearth, basic-oxygen, or electric-furnace steel. Thechemical composition thus determined shall not vary from thelimits specified in the applicable specification by more than theamounts prescribed in Tabl

48、e 5 and Table 6, but the severaldeterminations of any element, excluding lead, in a heat mayTABLE 1 ContinuedRephosphorized and Resulfurized Carbon SteelsD,FGrade Designation Carbon Manganese Phosphorous Sulfur Lead1213 0.13 max 0.701.00 0.070.12 0.240.33 .1215 0.09 max 0.751.05 0.040.09 0.260.35 .1

49、2L13 0.13 max 0.701.00 0.070.12 0.240.33 0.150.3512L14 0.15 max 0.851.15 0.040.09 0.260.35 0.150.3512L15 0.09 max 0.751.05 0.040.09 0.260.35 0.150.35High-Manganese Carbon SteelsB,C,D,E,FGrade Designation Former Designation Carbon Manganese Phosphorous, max Sulfur, max1513 . 0.100.16 1.101.40 0.040 0.0501518 . 0.150.21 1.101.40 0.040 0.0501522 . 0.180.24 1