ASTM A313 A313M-2013 Standard Specification for Stainless Steel Spring Wire《不锈钢弹簧线标准规格》.pdf

1、Designation: A313/A313M 101A313/A313M 13Standard Specification forStainless Steel Spring Wire1This standard is issued under the fixed designation A313/A313M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of last revision

2、. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1 NOTETable 1 layout editorially corrected in July 2010.1. Sco

3、pe*1.1 This specification covers austenitic austenitic, austenitic-ferritic, and age-hardenable stainless steel round spring wireintended especially for the manufacture of springs.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values state

4、d in eachsystem may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from thetwo systems may result in non-conformance with the standard.1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.2

5、. Referenced Documents2.1 ASTM Standards:2A555/A555M Specification for General Requirements for Stainless Steel Wire and Wire RodsA751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel ProductsE527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)2.

6、2 Society of Automotive Engineers Standard:3J 1086 Numbering Metals and Alloys3. Ordering Information3.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under thisspecification. Such requirements may include, but are not limited to the fo

7、llowing:3.1.1 Quantity (weight),3.1.2 Name of material (stainless steel spring wire),3.1.3 Finish (see 8.1),3.1.4 Dimension (diameter),3.1.5 Type designation (Table 1),3.1.6 ASTM designation and date of issue,3.1.7 Tensile strength level, when applicable (Table 11 and Table 12),3.1.8 Supplementary r

8、equirements for government procurement, and3.1.9 Special requirements.NOTE 1A typical ordering description is as follows:2000 lb (1000 kg) Stainless Steel Spring Wire, cold-drawn Class 1, bright finish, 0.032-in. (0.82 mm) diameter, in 100-lb (50 kg) 16-in. (0.4 m) coils,Type 302 to ASTM A313, dated

9、 _.1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of Subcommittee A01.17on Flat-Rolled and Wrought Stainless Steel.Current edition approved April 1, 2010Oct. 1, 2013. Published April 2010October 2013. O

10、riginally approved in 1947. Last previous edition approved in 20082010 asA313/A313M 08.A313/A313M 101. DOI: 10.1520/A0313_A0313M-10E01.10.1520/A0313_A0313M-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of A

11、STM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http:/www.sae.org.This document is not an ASTM standard and is intended only to provide the user

12、of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as p

13、ublished by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14. General Requirements for Delivery4.1 In addition to the req

14、uirements of this specification, all requirements of the current edition of Specification A555/A555Mshall apply. Failure to comply with the general requirements of Specification A555/A555M constitutes nonconformance with thisspecification.5. Manufacture5.1 Types 302 Class 1, 304, 305, 316, 321, 347,

15、 UNS S20230, and Grades S20430 and XM-28 shall be cold drawn to producethe required mechanical properties.5.2 Type 631, Type 302 Class 2, and Grade XM-16 shall be furnished in the cold-drawn condition ready for fabrication.Following fabrication Type 631 and Grade XM-16 shall be age or precipitation

16、hardened to produce their maximum strengthproperties. The tensile strengths to be obtained following the prescribed heat treatment are shown in Table 2 and Table 3 forhardened wire. Type 302 Class 2 shall be stress relieved following fabrication and meet the requirements shown in Table 4. Thenominal

17、 as-drawn tensile strengths are provided as a guide for the spring manufacturer.5.3 Grade S30151 shall be either cold drawn or cold drawn and heat treated to produce the required mechanical properties.6. Chemical Composition6.1 The steel shall conform to the requirements as to chemical composition p

18、rescribed in Table 1.6.2 Methods and practices relating to chemical analysis required by this specification shall be in accordance with Test Methods,Practices, and Terminology A751.7. Mechanical Requirements7.1 Tensile Properties:7.1.1 Types 302 Class 1 and 304 shall conform to the requirements show

19、n in Table 5.7.1.2 Types 305, 316, 321, and 347 shall conform to the requirements shown in Table 6.7.1.3 Type 631 shall conform to the requirements shown in Table 2 when heat treated 900F 482C for 1 h and air cooled.7.1.4 Grade XM-16 shall conform to the requirements shown in Table 3 when heat treat

20、ed 850F 454C for 12 h and aircooled.7.1.5 Grade XM-28 shall conform to the requirements shown in Table 7.7.1.6 Type 302 Class 2 shall conform to the requirements shown in Table 4.7.1.7 Grade S20430 shall conform to the requirements shown in Table 8.TABLE 1 Chemical RequirementsUNSDesignationAType Co

21、mposition,B %Carbon Manganese Phosphorus Sulfur Silicon Chromium Nickel Molybdenum Nitrogen Other ElementsAustenitic GradesS 24100 XM-28 0.15 11.014.0 0.060 0.030 1.00 16.519.0 0.502.50 0.200.45S 30200 302 0.12 2.00 0.045 0.030 1.00 17.019.0 8.010.0 0.10S 30400 304 0.08 2.00 0.045 0.030 1.00 18.020.

22、0 8.010.5 0.10S 30500 305 0.12 2.00 0.045 0.030 1.00 17.019.0 10.513.0S 31600 316 0.07 2.00 0.045 0.030 1.00 16.518.0 10.513.5 2.002.50 0.10S 32100S 347003213470.080.082.002.000.0450.0450.0300.0301.001.0017.019.017.019.09.012.09.013.0Ti 5C min(Cb + Ta)10C minS 30151 0.070.09 1.502.00 0.025 0.010 1.2

23、01.80 16.018.0 7.09.0 0.501.00 0.070.11 Cu 0.40 maxS 20230 0.020.06 2.06.0 0.045 0.030 1.00 17.019.0 2.04.5 1.0 0.130.25 Cu 2.0-4.0Age-Hardenable GradesS 17700 631 0.09 1.00 0.040 0.030 1.00 16.018.0 6.57.8 Al 0.751.50S 45500 XM-16 0.05 0.50 0.040 0.030 0.50 11.012.5 7.59.5 0.50 max Ti 0.801.40Cu 1.

24、502.50(Cb + Ta)0.100.50S 20430 . . . 0.15 6.59.0 0.060 0.030 1.00 15.517.5 1.53.5 0.050.25 Cu 2.04.0Austenitic-Ferritic GradesS32205 . . . 0.030 2.00 0.030 0.020 1.00 22.023.0 4.56.5 3.003.50 0.140.20A New designations established in accordance with Practice E527 and SAE J 1086, Practice for Numberi

25、ng Metals and Alloys (UNS).B Maximum unless range is shown.A313/A313M 1327.1.8 Cold drawn grade S30151 shall conform to the requirements shown in Table 9.7.1.9 Cold drawn grade UNS S20230 shall conform to the requirements shown in Table 10.7.1.10 Cold drawn, as delivered grade S32205 shall conform t

26、o the requirements shown in Table 11 and Table 12.7.2 Wrap Test:7.2.1 Wire 0.162 in. 4.11 mm and smaller in diameter shall wind on itself as an arbor without breaking.7.2.2 Wire larger than 0.162 in. 4.11 mm in diameter shall wind without breaking on a mandrel having a diameter twice thediameter of

27、the wire.7.3 Uniformity (Coil Test):7.3.1 In the as-cold drawn condition, a specimen coil shall be wound on an arbor of the size specified in Table 1113 to forma tightly wound coil.7.3.2 After winding, the specimen coil shall be stretched to a permanent set four times its as-wound length.After this

28、treatment,the specimen coil shall show uniform pitch with no splits or fractures.TABLE 2 Tensile Strength Requirements for Type 631ADiameter, in. mm Cold Drawn ConditionC, ksi MPaNominalCondition CH-900B , ksi MPamin max0.010 0.25 to 0.015 0.38, incl 295 2035 335 2310 365 2515Over 0.015 0.38 to 0.02

29、0 0.51, incl 290 2000 330 2275 360 2480Over 0.020 0.51 to 0.029 0.74, incl 285 1965 325 2240 355 2450Over 0.029 0.74 to 0.041 1.04, incl 275 1895 320 2205 350 2415Over 0.041 1.04 to 0.051 1.30, incl 270 1860 310 2135 340 2345Over 0.051 1.30 to 0.061 1.55, incl 265 1825 305 2100 335 2310Over 0.061 1.

30、55 to 0.071 1.80, incl 257 1770 297 2050 327 2255Over 0.071 1.80 to 0.086 2.18, incl 255 1760 292 2015 322 2220Over 0.086 2.18 to 0.090 2.29, incl 245 1690 282 1945 312 2150Over 0.090 2.29 to 0.100 2.54, incl 242 1670 279 1925 309 2130Over 0.100 2.54 to 0.106 2.69, incl 238 1640 274 1890 304 2095Ove

31、r 0.106 2.69 to 0.130 3.30, incl 236 1625 272 1875 302 2080Over 0.130 3.30 to 0.138 3.50, incl 230 1585 260 1795 290 2000Over 0.138 3.50 to 0.146 3.71, incl 228 1570 258 1780 288 1985Over 0.146 3.71 to 0.162 4.11, incl 226 1560 256 1765 286 1970Over 0.162 4.11 to 0.180 4.57, incl 224 1545 254 1750 2

32、84 1960Over 0.180 4.57 to 0.207 5.26, incl 222 1530 252 1740 282 1945Over 0.207 5.26 to 0.225 5.72, incl 218 1505 248 1710 278 1915Over 0.225 5.72 to 0.306 7.77, incl 213 1470 242 1670 272 1875Over 0.306 7.77 to 0.440 11.2, incl 207 1425 235 1620 265 1825Over 0.440 11.2 to 0.625 15.88, incl 203 1400

33、 230 1585 260 1795A When wire is specified in straightened and cut lengths, the minimum tensile strength shall be 90 % of the values listed in the table.B Aged at 900F 482C for 1 h and air cooled.TABLE 3 Tensile Strength Requirements for Grade XM-16ADiameter, in. mm Cold Drawn, ksi MPaNominalAge Har

34、denedB , ksi MPamin max0.010 0.25 to 0.040 1.02, incl 245 1690 320 2205 350 2415Over 0.040 1.02 to 0.050 1.27, incl 235 1620 310 2135 340 2345Over 0.050 1.27 to 0.060 1.52, incl 225 1550 305 2100 335 2310Over 0.060 1.52 to 0.075 1.90, incl 220 1515 295 2035 325 2240Over 0.075 1.90 to 0.085 2.16, inc

35、l 215 1480 290 2000 320 2205Over 0.085 2.16 to 0.095 2.41, incl 210 1450 285 1965 315 2170Over 0.095 2.41 to 0.110 2.79, incl 200 1380 278 1915 308 2125Over 0.110 2.79 to 0.125 3.17, incl 195 1345 272 1875 302 2080Over 0.125 3.17 to 0.150 3.81, incl 190 1310 265 1825 295 2035Over 0.150 3.81 to 0.500

36、 12.7, incl 180 1240 260 1795 290 2000A When wire is straightened and cut lengths, the minimum tensile strength shall be 90 % of the values listed in the table.B Aged at 850F 454C for 12 h and air cooled.TABLE 4 Tensile Strength Requirement for Type 302 Class 2Diameter, in. mmksi MPaCold DrawnNomina

37、lStress RelievedAmin max0.050 1.30 to 0.1604.00, incl290 2000 290 2000 340 2345A Stress relieved at 800 to 850F 430 to 455C for 12 h and air cooled.A313/A313M 1337.4 CastA loop or ring shall be cut from the bundle and allowed to fall on the floor. The wire shall lie flat and not spring upor show a w

38、avy condition.7.5 Bend TestWhen specified in the purchase order, Types 302, 304, 305, 316, 321, and 347 shall be tested by the bend test.A piece not more than 10 in. 254 mm long shall be selected from each test sample. These specimens shall be tested in a bendingmachine conforming substantially to F

39、ig. 1. Bends shall be made at as nearly a uniform rate as possible, not exceeding 50 bendsper minute, and in no case shall the speed be so great as to cause undue heating of the wire. The test specimen shall be bent backand forth through a total angle of 180 until failure occurs. Each 90 movement in

40、 either direction shall be counted as one bend.The wire shall withstand the minimum number of bends specified in Table 5 and Table 6.8. Finish8.1 Stainless steel spring wire is supplied with different types of finish such as bright, copper, lead, oxide, and other.9. Keywords9.1 austenitic-ferritic d

41、uplex; austeniticaustenitic stainless steel; precipitation hardening stainless steel; stainless steel; stainlesssteel spring wireTABLE 5 Tensile Strength Requirements for Types 302 Class 1 and 304ADiameter, in. mm Bend Test Minimum Number ofBends ksi MPamin maxUp to 0.009 0.23, incl . . . 325 2240 3

42、55 2450Over 0.009 0.23 to 0.010 0.25, incl . . . 320 2205 350 2415Over 0.010 0.25 to 0.011 0.28, incl . . . 318 2190 348 2400Over 0.011 0.28 to 0.012 0.30, incl . . . 316 2180 346 2385Over 0.012 0.30 to 0.013 0.33, incl . . . 314 2165 344 2370Over 0.013 0.33 to 0.014 0.36, incl . . . 312 2150 342 23

43、60Over 0.014 0.36 to 0.015 0.38, incl . . . 310 2135 340 2345Over 0.015 0.38 to 0.016 0.41, incl . . . 308 2125 338 2330Over 0.016 0.41 to 0.017 0.43, incl . . . 306 2110 336 2315Over 0.017 0.43 to 0.018 0.46, incl . . . 304 2095 334 2300Over 0.018 0.46 to 0.020 0.51, incl . . . 300 2070 330 2275Ove

44、r 0.020 0.51 to 0.022 0.56, incl . . . 296 2040 326 2250Over 0.022 0.56 to 0.024 0.61, incl . . . 292 2015 322 2220Over 0.024 0.61 to 0.026 0.66, incl 8 291 2005 320 2205Over 0.026 0.66 to 0.028 0.71, incl 8 289 1995 318 2190Over 0.028 0.71 to 0.031 0.79, incl 8 285 1965 315 2170Over 0.031 0.79 to 0

45、.034 0.86, incl 8 282 1945 310 2135Over 0.034 0.86 to 0.037 0.94, incl 8 280 1930 308 2125Over 0.037 0.94 to 0.041 1.04, incl 8 275 1895 304 2095Over 0.041 1.04 to 0.045 1.14, incl 8 272 1875 300 2070Over 0.045 1.14 to 0.050 1.27, incl 8 267 1840 295 2035Over 0.050 1.27 to 0.054 1.37, incl 8 265 182

46、5 293 2020Over 0.054 1.37 to 0.058 1.47, incl 7 261 1800 289 1990Over 0.058 1.47 to 0.063 1.60, incl 7 258 1780 285 1965Over 0.063 1.60 to 0.070 1.78, incl 7 252 1735 281 1935Over 0.070 1.78 to 0.075 1.90, incl 7 250 1725 278 1915Over 0.075 1.90 to 0.080 2.03, incl 7 246 1695 275 1895Over 0.080 2.03

47、 to 0.087 2.21, incl 7 242 1670 271 1870Over 0.087 2.21 to 0.095 2.41, incl 7 238 1640 268 1850Over 0.095 2.41 to 0.105 2.67, incl 5 232 1600 262 1805Over 0.105 2.67 to 0.115 2.92, incl 5 227 1565 257 1770Over 0.115 2.92 to 0.125 3.17, incl 5 222 1530 253 1745Over 0.125 3.17 to 0.135 3.43, incl 3 217 1495 248 1710Over 0.135 3.43 to 0.148 3.76, incl 3 210 1450 241 1660Over 0.148 3.76 to 0.162 4.11, incl 3 205 1415 235 1620Over 0.162 4.11 to 0.177 4.50, incl 3 198 136