ASTM A411-2008(2017) Standard Specification for Zinc-Coated (Galvanized) Low-Carbon Steel Armor Wire《镀锌低碳钢铠装线的标准规格》.pdf

1、Designation: A411 08 (Reapproved 2017)Standard Specification forZinc-Coated (Galvanized) Low-Carbon Steel Armor Wire1This standard is issued under the fixed designation A411; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers zi

3、nc-coated low-carbon steelwire for use in armoring for protection against damage ofsubmarine and underground cables used for communication,control, or power purposes.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions t

4、o SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides

5、 and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA938 Test Method for Torsion Testing of WireB6

6、Specification for ZincE8 Test Methods for Tension Testing of Metallic Materials3. Ordering Information3.1 It shall be the responsibility of the purchaser to specifyall requirements that are necessary for material under thisspecification. Such requirements may include, but are notlimited to, the foll

7、owing information:3.1.1 Quantity of each size,3.1.2 Wire size, diameter in inches or (millimetres) (Section12), and3.1.3 Weight (Mass), inside diameter, and method of band-ing of coils.4. Zinc for Coating4.1 The slab zinc used for the coating shall be any grade ofzinc conforming to Specification B6.

8、5. Base Metal5.1 The base metal shall be manufactured by any commer-cially accepted steel making practice, and of such quality that,when processed and zinc-coated, the finished wire shall havethe properties prescribed in this specification.6. Joints6.1 The wire shall be furnished in coils of one con

9、tinuouslength. Welds made prior to final wire drawing shall bepermitted.7. Tensile Strength7.1 The zinc-coated wire shall have a tensile strength of notless than 50 000 psi (345 MPa), nor more than 70 000 psi (483MPa). The tensile strength of the zinc-coated wire shall bedetermined in accordance wit

10、h Test Methods E8. The diameterof the wire shall be measured over the zinc coating for thepurpose of calculating the tensile strength.8. Elongation8.1 The zinc-coated wire shall have an elongation of not lessthan 10 % in 10 in. (254 mm) for nominal sizes 0.284 in. (7.21mm) and smaller. Nominal sizes

11、 larger than 0.284 in. shall havean elongation of not less than 9 % in 10 in. The elongation shallbe determined as the permanent increase in length after failureof a marked section of the wire originally 10 in. in length.9. Torsion Test9.1 The zinc-coated wire shall withstand without fracturethe min

12、imum number of turns specified in Table 1. This testshall be done in accordance with Test Method A938 and thenumber of turns to failure shall meet the requirements of Table1.1This specification is under the jurisdiction of ASTM Committee A05 onMetallic-Coated Iron and Steel Products and is the direc

13、t responsibility ofSubcommittee A05.12 on Wire Specifications.Current edition approved Sept. 1, 2017. Published September 2017. Originallyapproved in 1957. Last previous edition approved in 2013 as A411 - 08(2013). DOI:10.1520/A0411-08R17.2For referenced ASTM standards, visit the ASTM website, www.a

14、stm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis inte

15、rnational standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Co

16、mmittee.110. Weight of Coating10.1 The weight of zinc coating, in ounces per square footor (grams per square metre) of uncoated wire surface, shall benot less than that specified in Table 2.10.2 Weight of Coating TestThe zinc coating shall betested for weight by a stripping test in accordance with T

17、estMethods A90/A90M.11. Adherence of Coating11.1 The zinc coating shall remain adherent when the wireis wrapped at a rate of not more than 15 turns per minute in aclose helix of at least 2 turns around a cylindrical mandrel ofthe diameter specified in Table 3. The zinc coating shall beconsidered as

18、meeting this requirement if, when the wire iswrapped about the specified mandrel, the coating does not flakeand none of it can be removed from the wire by rubbing withfingers. Loosening or detachment during the adhesion test ofsuperficial, small particles of zinc formed by mechanicalpolishing of the

19、 surface of zinc-coated wire shall not beconsidered cause for rejection.12. Size and Permissible Variations12.1 SizeThe size of the zinc-coated wires shall be ex-pressed as the diameter of the wire in decimal fractions of aninch or (millimetres).12.2 Permissible VariationsThe permissible variations

20、ofthe zinc-coated wire from the nominal diameter shall be asspecified in Table 4.13. Workmanship, Finish, and Appearance13.1 The surface of the wire shall be free from injuriousscale, flaws, splits, and other imperfections not consistent withgood commercial practice. The coating shall be continuous

21、andreasonably uniform.14. Sampling14.1 The inspector shall select at random one sample coilfrom every 10 coils in the first 100 coils of the lot, and onesample for every additional 35 coils but not less than 3 coilsfrom the entire lot. From each coil of zinc-coated wire thusselected, a sample of sui

22、table length shall be taken for theweight of coating and mechanical tests as specified in Sections711, inclusive.15. Inspection15.1 Unless otherwise specified in the contract or purchaseorder, the manufacturer is responsible for the performance ofall inspection and test requirements specified in thi

23、s standard.Except as otherwise specified in the contract or purchase order,the manufacturer may use his own or any other suitable facilityfor the performance of the inspection and test requirementsunless disapproved by the purchaser at the time the order isplaced. The purchaser shall have the right

24、to perform any of theinspections and tests set forth in this standard when suchinspections and tests are deemed necessary to assure that thematerial conforms to prescribed requirements.16. Rejection16.1 Failure of any of the test specimens to comply with therequirements of this specification shall c

25、onstitute grounds forrejection of the lot represented by the specimen. The lot may bere-submitted for inspection by testing every coil for thecharacteristics in which the specimen failed, and sorting out thedefective coils.17. Packaging17.1 The finished zinc-coated wire shall be furnished incompact

26、coils reasonably symmetrical in shape. The weight,inside diameter, and method of banding of the coils shall beagreed upon between the manufacturer and the purchaser.TABLE 1 Minimum Number of TurnsNominal Wire Diameter, in. (mm)MinimumTurns(8 in. gage length)0.239 (6.07) and over 70.238 to 0.166 (6.0

27、5 to 4.22) 90.165 to 0.110 (4.19 to 2.79) 130.109 to 0.065 (2.77 to 1.65) 19TABLE 2 Minimum Weights of Zinc CoatingNominal Diameter ofCoated Wire, in. (mm)Minimum Weight of ZincCoating oz/ft2(g/m2)ofUncoated Wire Surface0.340 (8.64) 1.00 (300)0.300 (7.62) 1.00 (300)0.284 (7.21) 1.00 (300)0.259 (6.58

28、) 1.00 (300)0.238 (6.05) 1.00 (300)0.220 (5.59) 1.00 (300)0.203 (5.16) 1.00 (300)0.165 (4.19) 0.90 (270)0.134 (3.40) 0.80 (240)0.109 (2.77) 0.80 (240)0.083 (2.11) 0.60 (180)0.065 (1.65) 0.50 (150)TABLE 3 Mandrel Diameter for Adherence of Coating TestsWire Diameters, in. (mm) Mandrel Size0.259 (6.58)

29、 and over 50.258 to 0.134 (6.55 to 3.40) 30.133 (3.38) and under 2TABLE 4 Permissible Variations in Diameter of Zinc-Coated WireNOTE 1It is recognized that the surfaces of zinc coatings, particularlythose produced by hot-dip galvanizing, are not perfectly smooth anddevoid of irregularities. If the t

30、olerances shown are rigidly applied to suchirregularities that are inherent to the product, unjustified rejections of wirethat would actually be satisfactory for use could occur. Therefore, it isintended that these tolerances be used in gaging the uniform areas of thegalvanized wire.Nominal Diameter

31、 of Coated Wire, in. (mm)Permissible Variations, plusor minus, in. (mm)0.340 to 0.260 (8.64 to 6.60) 0.006 (0.15)0.259 to 0.166 (6.58 to 4.22) 0.005 (0.13)0.165 to 0.109 (4.19 to 2.77) 0.004 (0.10)0.108 to 0.065 (2.74 to 1.65) 0.003 (0.08)A411 08 (2017)218. Marking18.1 Adurable tag shall be attached

32、 to each coil showing thenominal size of wire and the name or mark of the manufacturer.The starting end of each coil shall be indicated by a suitabletag.19. Keywords19.1 armor wire; zinc coated steel armor wireASTM International takes no position respecting the validity of any patent rights asserted

33、 in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the

34、 responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive c

35、areful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM Internati

36、onal, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 08 (2017)3