1、Designation: A 505 00 (Reapproved 2005)Standard Specification forSteel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled,General Requirements for1This standard is issued under the fixed designation A 505 ; the number immediately following the designation indicates the year oforiginal adoption or,
2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1
3、 This specification covers a group of common require-ments that, unless otherwise specified in the material specifi-cation, apply to hot-rolled and cold-rolled alloy steel sheet andstrip under each of the following specifications: A 506, A 507,and A 873/A 873M.1.2 In case of any conflict in requirem
4、ents, the requirementsof the individual material specification shall prevail over thoseof this general specification.1.3 The purchaser may specify additional requirementswhich do not negate any of the provisions of this generalspecification or of the individual material specification. Suchadditional
5、 requirements, the acceptance of which are subject tonegotiation with the supplier, must be included in the orderinformation (see 4.1.9).1.4 For purposes of determining conformance with thisspecification and the various material specifications referencedin 1.1, values shall be rounded to the nearest
6、 unit in theright-hand place of figures used in expressing the limitingvalues in accordance with the rounding provisions of TestMethods and Definitions A 370 and Test Methods, Practices,and Terminology A 751.2. Referenced Documents2.1 ASTM Standards:2A 370 Test Methods and Definitions for Mechanical
7、 Testingof Steel ProductsA 506 Specification for Alloy and Structural Alloy Steel,Sheet and Strip, Hot-Rolled and Cold-RolledA 507 Specification for Drawing Alloy Steel, Sheet andStrip, Hot-Rolled and Cold-RolledA 700 Practices for Packaging, Marking, and LoadingMethods for Steel Products for Domest
8、ic ShipmentA 751 Test Methods, Practices, and Terminology forChemical Analysis of Steel ProductsA 873/A 873M Specification for Steel Sheet and Strip,Chromium-Molybdenum Alloy, for Pressure Vessels3A 919 Terminology Relating to Heat Treatment of Metals32.2 Federal Standard:4Fed. Std. No. 123 Marking
9、for Shipment (Civil Agencies)2.3 Military Standard:4MIL-STD-163 Steel Mill Products, Preparation for Ship-ment and Storage3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 sheet and striphot-rolled and cold-rolled alloy steelsheet and strip is classified as shown in Table 1.3.1.
10、2 exclusivewhen used in relation to ranges, as forranges of thicknesses in the tables of permissible variations indimensions, the term “exclusive” is intended to exclude onlythe greater value of the range. Thus a range from 60 to 72 in.(1524 to 1829 mm) exclusive includes 60 in. but does notinclude
11、72 in.3.1.3 manufacturer (material manufacturer)an organiza-tion that performs or directly controls one or more operations,such as melting, rolling, coiling, and heat treatment, that affectsthe chemical composition or mechanical properties of thematerial.4. Ordering Information4.1 Orders shall inclu
12、de the following information, as nec-essary, to describe adequately the desired material:4.1.1 Specification designation, including year of issue,4.1.2 Chemical composition (grade),4.1.3 Classification of the material (that is, hot-rolled sheet),4.1.4 Dimensions (thickness, width, length) in decimal
13、inches,4.1.5 Quantity (weight or number of pieces),4.1.6 Condition (that is, “hot-rolled,” “cold-rolled”),4.1.7 Heat treatment required, if any,1This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stainless Steel, and Related Alloys and is the direct responsibility of Subcomm
14、itteeA01.19 on Steel Sheet and Strip.Current edition approved March 1, 2005. Published March 2005. Originallyapproved in 1964. Last previous edition approved in 2000 as A 505 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.
15、For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1Copyright ASTM International, 100 Barr H
16、arbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.1.8 Type of edge,4.1.9 Additional information as specified in the individualmaterial specification,4.1.10 Any special requirements not specified in the indi-vidual material specification, and4.1.11 Whether certification of c
17、ompliance or test reportsare required.5. Materials and Manufacture5.1 Melting ProcessUnless otherwise specified in theindividual material specification, the steel may be made by anyprocess that produces material that conforms to the specifiedrequirements.5.2 Hot or Cold RollingThe sheet and strip sh
18、all beproduced by hot rolling or cold rolling, as specified in theindividual material specification and as specified on the order.5.3 Heat TreatmentWhen heat treatment is required, itshall be performed in accordance with the requirements speci-fied in the individual material specification. Heat trea
19、tmentmay be performed by either the manufacturer or the purchaser;however, if the purchaser intends to perform the heat treatment,it shall be so stated on the order.5.3.1 Heat treatment terms shall be in accordance withTerminology A 919.6. Chemical Requirements Chemical Requirements6.1 Cast or Heat
20、Analysis of each cast or heat shall be madeby the manufacturer to determine the percentage of elementsspecified in the individual material specification. This analysisshall be made from a test specimen preferably taken during theteeming of the cast or heat. The chemical composition thusdetermined sh
21、all be reported to the purchaser or his represen-tative upon request, and shall conform to the cast or heatanalysis requirements of the applicable material specification.6.2 Product or Verification Analysis An analysis may bemade by the purchaser from finished material representing eachcast or heat.
22、 The composition thus determined shall conform tothe requirements for product analysis specified in the indi-vidual material specification or on the order; however, if onlycast or heat analysis requirements are specified in the materialspecification or on the order, the composition determined onprod
23、uct analysis shall conform to those requirements subject tothe product analysis tolerances specified in Table 2.6.3 Referee AnalysisIn case referee analysis is required toresolve a dispute concerning the results of a chemical analysis,the procedures for performing the referee analysis shall be inacc
24、ordance with Test Methods, Practices, and TerminologyA 751.7. Metallurgical Structure7.1 The requirements for metallurgical structure, if any,shall be as specified in the individual material specification.8. Mechanical Property Requirements8.1 RequirementsThe requirements for mechanical prop-erties,
25、 if any, shall be as specified in the individual materialspecification.8.2 Number of TestsThe number of specimens shall be asspecified in the individual material specification.8.3 Location and Orientation of Tension Test SpecimensUnless otherwise specified in the individual material specifi-cation,
26、tension test specimens shall be the full thickness of thematerial. The test coupons shall be taken from the material inits finished condition except as otherwise provided in 8.4; shallbe taken approximately midway between the edge and center-line of the sheet or strip; and shall be taken such that t
27、he longaxis of the test specimen will be transverse to the final directionof rolling.8.4 Heat Treatment of Test Coupons:8.4.1 When heat treatment is required by the materialspecification and is to be performed by the purchaser or hisagent, and the material is to be supplied by the manufacturer ina c
28、ondition other than that required by the material specifica-tion, the material shall be qualified on the basis of tests madeon specimens taken from coupons, obtained from the materialin its as-shipped condition, that have been heat treated inaccordance with the requirements specified in the material
29、specification or on the order. If the heat-treatment temperaturesare not specified, the manufacturer shall heat treat the couponsunder conditions he considers appropriate.8.4.2 When specified on the order, the test coupons may besubjected to additional heat treatment to simulate thermaltreatments th
30、at will be used during fabrication.8.4.3 The purchaser shall be informed of the proceduresfollowed in heat treating the test coupons.8.5 Test Methods:8.5.1 All tests shall be conducted in accordance with TestMethods and Definitions A 370.8.5.2 Yield strength shall be determined either by the 0.2 %of
31、fset method or by the 0.5 % extension-under-load method.9. Quality9.1 GeneralSheet and strip furnished under this specifi-cation shall be clean, sound, and free of internal or externalimperfections which would make the material unsuitable forthe intended application. Care should be taken to avoid cr
32、acks,seams, slivers, grooves, laminations, pits, blisters, buckles, coilbreaks, creases, holes, pickling stains and patches, ragged andtorn edges, and “rolled-in” dirt and scale.9.2 Surface FinishThe degree or amount of surface im-perfections on material in cut lengths shall be such that only areaso
33、nable amount of metal finishing is required. Slight surfaceimperfections that are completely removable without reducingthe thickness below the minimum permissible limits shall notbe considered to be defects. Coils may contain some abnormaldefects such as holes, welds, etc., which render a portion of
34、 thecoil unusable, since the inspection of coils does not afford thesame opportunity to reject portions containing defects as is thecase with cut lengths. However, an excessive number ofabnormal imperfections is cause for rejection.10. Edges10.1 EdgesThe types of edges procurable in hot-rolledand in
35、 cold-rolled alloy-steel sheet and strip are as follows:10.2 Hot-Rolled Sheet and Strip:10.2.1 Mill EdgeNormal edge produced in hot rolling thatdoes not conform to any definite contour.A 505 00 (2005)210.2.2 Cut EdgeApproximately square edge resultingfrom the cutting of sheet into one or more desire
36、d widths bymeans of rotary knives (slit edge) or blade shears (shearededge).10.2.3 Square EdgeType of mill edge produced by hotedge-rolling; furnished on strip only.10.3 Cold-Rolled Sheet:10.3.1 Cut EdgeSame description as shown in 10.2.2 forhot-rolled sheet and strip.10.4 Cold-Rolled Strip:10.4.1 N
37、o. 1 EdgePrepared edge of a specified round orsquare contour that is produced when a very accurate width isrequired.10.4.2 No. 2 EdgeNatural mill edge carried through thecold rolling from the hot-rolled strip without additional pro-cessing of the edge.10.4.3 No. 3 EdgeApproximately square edge produ
38、cedby slitting.10.4.4 No. 4 EdgeRounded edge produced by edge roll-ing either the natural edge of hot-rolled strip or slit-edge strip.Used when an approximately round edge is desired and whenthe finish of the edge is not important.10.4.5 No. 5 EdgeSquare edge produced by edge rollingor filing for th
39、e purpose of eliminating burr.10.4.6 No. 6 EdgeSquare edge produced by edge rollingthe natural edge of hot-rolled strip or slit-edge strip, when thewidth tolerances and finish required are not as exacting as forthe No. 1 Edge.11. Permissible Variations in Dimensions11.1 The permissible variations in
40、 dimensions (see Table 3)for hot-rolled and cold-rolled alloy steel sheet and strip shall bein accordance with Tables 4-22.12. Identification of Product12.1 As a minimum, the material shall be identified with themanufacturers name or brand, the specification designation,weight, purchasers order numb
41、er, and material identificationwhich is traceable to the heat or cast.12.2 The identification shall be legibly stenciled on top ofeach lift or shown on a tag attached to each coil or shippingunit.12.3 When specified on the order, each sheet shall beidentified as agreed upon.13. Retests13.1 The retes
42、t provisions of Test Methods and DefinitionsA 370 shall apply.13.2 If the results of any tests do not conform to thespecified requirements, (unless otherwise specified in theindividual material specification), retests may be made ondouble the original number of specimens from the same lot,each of wh
43、ich must conform to the requirements specified. Ifthe results of the retests do not conform to the specifiedrequirements, the lot shall be rejected.14. Inspection and Testing14.1 When the order specifies that the purchaser will inspectthe material and witness testing, the inspector representing thep
44、urchaser shall have entry at all times while work on thecontract of the purchaser is being performed, to all parts of themanufacturers works that concern the manufacture of thematerial ordered. The manufacturer shall afford the inspectorall reasonable facilities to satisfy the inspector that the mat
45、erialis being furnished in accordance with the specification.14.2 All tests (except product analysis) and inspection shallbe made at the place of manufacture before shipment, unlessotherwise specified on the order, and shall be so conducted asnot to interfere unnecessarily with the operation of the
46、works.15. Rework and Retreatment15.1 If inspection and test results fail to conform to thespecified requirements, the material may be reworked orretreated, if the manufacturer can assure that the cause offailure is curable and that the quality of the material shallconform to the specified requiremen
47、ts. After retreatment,testing shall be done in accordance with the material specifi-cation requirements.16. Rejection Subsequent to Shipment16.1 Material that shows characteristics not in conformancewith the material specification subsequent to its initial accep-tance may be rejected. In such cases,
48、 the manufacturer shouldbe notified in a timely manner.17. Certification17.1 When specified on the order, a certification of compli-ance shall be furnished that the material was manufactured,sampled, tested, and inspected in accordance with the require-ments of the applicable specification.17.2 When
49、 specified on the order, a report of the test resultsshall be furnished.17.3 A signature is not required on the certification ofcompliance or the report of test results. However, the documentshall clearly identify the organization submitting the document.Notwithstanding the absence of a signature, the organizationsubmitting the document is responsible for the content of thedocument.18. Packaging, Marking, and Loading for Shipment18.1 Packaging, marking, and loading for shipment shall bein accordance with those procedures recommended in PracticesA 700.18.2 F
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1