ASTM A572 A572M-2015 Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel《高强度低合金铌-钒结构钢的标准规格》.pdf

1、Designation: A572/A572M 13aA572/A572M 15 American Association StateHighway and TransportationOfficals StandardAASHTO No.: M223Standard Specification forHigh-Strength Low-Alloy Columbium-Vanadium StructuralSteel1This standard is issued under the fixed designation A572/A572M; the number immediately fo

2、llowing the designation indicates the yearof original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been app

3、roved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers five grades of high-strength low-alloy structural steel shapes, plates, sheet piling, and bars. Grades42 290, 50 345, and 55 380 are intended for riveted, bolted, or welded structures. Grades 60 415 an

4、d 65 450 are intendedfor riveted or bolted construction of bridges, or for riveted, bolted, or welded construction in other applications.1.2 For applications, such as welded bridge construction, where notch toughness is important, notch toughness requirements areto be negotiated between the purchase

5、r and the producer.1.3 Specification A588/A588M shall not be substituted for Specification A572/A572M without agreement between thepurchaser and the supplier.1.4 The use of columbium, vanadium, titanium, nitrogen, or combinations thereof, within the limitations noted in Section 5, isrequired; the se

6、lection of type (1, 2, 3, or 5) is at the option of the producer, unless otherwise specified by the purchaser. (SeeSupplementary Requirement S90.)1.5 The maximum thicknesses available in the grades and products covered by this specification are shown in Table 1.1.6 When the steel is to be welded, a

7、welding procedure suitable for the grade of steel and intended use or service is to beutilized. See Appendix X3 of Specification A6/A6M for information on weldability.1.7 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units

8、are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be usedindependently of the other, without combining values in any way.1.8 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such note

9、s andfootnotes, excluding those in tables and figures, do not contain any mandatory requirements.1.9 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additionalrequirements, including additional testing requirements and the reporting

10、of additional tests, of A6/A6M apply.2. Referenced Documents2.1 ASTM Standards:2A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet PilingA36/A36M Specification for Carbon Structural SteelA514/A514M Specification for High-Yield-Strength, Quenched

11、 and Tempered Alloy Steel Plate, Suitable for WeldingA588/A588M Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi 345 MPa Minimum Yield Point, withAtmospheric Corrosion Resistance1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and

12、RelatedAlloys and is the direct responsibility of Subcommittee A01.02on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.Current edition approved Nov. 1, 2013March 1, 2015. Published November 2013March 2015. Originally approved in 1966. Last previous edition approved in 2013 asA572/A

13、572M 13.A572/A572M 13a. DOI: 10.1520/A0572_A0572M-13A. 10.1520/A0572_A0572M-15.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on

14、 the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users

15、 consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshoho

16、cken, PA 19428-2959. United States13. General Requirements for Delivery3.1 Structural products furnished under this specification shall conform to the requirements of the current edition ofSpecification A6/A6M, for the specific structural product ordered, unless a conflict exists in which case this

17、specification shallprevail.3.2 Coils are excluded from qualification to this specification until they are processed into a finished structural product.Structural products produced from coil means structural products that have been cut to individual lengths from a coil. Theprocessor directly controls

18、, or is responsible for, the operations involved in the processing of a coil into a finished structuralproduct. Such operations include decoiling, leveling or straightening, hot-forming or cold-forming (if applicable), cutting to length,testing, inspection, conditioning, heat treatment (if applicabl

19、e), packaging, marking, loading for shipment, and certification.NOTE 1For structural products produced from coil and furnished without heat treatment or with stress relieving only, two test results are to be reportedfor each qualifying coil. Additional requirements regarding structural products prod

20、uced from coil are described in A6/A6M.4. Materials and Manufacture4.1 The steel shall be killed5. Chemical Composition5.1 The heat analysis shall conform to the requirements prescribed in Table 2 and Table 3.5.2 The steel shall conform on product analysis to the requirements prescribed in Table 2 a

21、nd Table 3, subject to the productanalysis tolerances in Specification A6/A6M.6. Mechanical Properties6.1 Tensile Properties:6.1.1 The material as represented by the test specimens shall conform to the tensile properties given in Table 4.7. Test Reports7.1 In addition to the Test Reports requirement

22、s in Specification A6/A6M, when Specification A588/A588M is substituted forSpecification A572/A572M, the test report shall include the statement “Specification A588/A588M substituted.”8. Keywords8.1 bars; bolted construction; bridges; buildings; columbium-vanadium; high-strength; low-alloy; plates;

23、riveted construction;shapes; sheet piling; steel; structural steel; welded constructionTABLE 1 Maximum Product Thickness or SizeGradeYield Point, min Maximum Thickness or SizeZees and RolledTeesksi MPa Plates and BarsStructural ShapeFlange or LegThickness Sheet Pilingin. mm in. mm42 290A 42 290 6 15

24、0 all all all all50 345A 50 345 4B 100B all all all all55 380 55 380 2 50 all all all all60 415A 60 415 114C 32C 2 50 all all65 450 65 450 114 32 2 50 not available allA In the above tabulation, Grades 42, 50, and 60 290, 345, and 415, are the yield point levels most closely approximating a geometri

25、c progression pattern between 36ksi 250 MPa, min, yield point steels covered by Specification A36/A36M and 100 ksi 690 MPa, min, yield strength steels covered by Specification A514/A514M.B Round bars up to and including 11 in. 275 mm in diameter are permitted.C Round bars up to and including 312 in.

26、 90 mm in diameter are permitted.A572/A572M 152TABLE 2 Chemical RequirementsA(Heat Analysis)Diameter, Thickness,or DistanceBetween ParallelFaces, in. mmPlates and BarsStructuralShapeFlange orLegThickness,in. mmGrade Carbon,max, % Manganese,Bmax, % Phosphorus,max, %Sulfur,max,%SiliconPlates to 112 in

27、. 40mm Thick,Shapes withFlange or LegThickness to 3 in.75 mm inclusive,Sheet Piling,Bars, Zees, andRolled TeesCPlates Over 112 in.40 mm Thick andShapes with FlangeThicknessOver 3 in.75 mmmax, % range, %6 150 all 42 290 0.21 1.35D 0.04 0.05 0.40 0.150.404 100E all 50 345 0.23 1.35D 0.04 0.05 0.40 0.1

28、50.402 50F all 55 380 0.25 1.35D 0.04 0.05 0.40 0.15-0.40114 32F #2 50 60 415 0.26 1.35D 0.04 0.05 0.40 G12 114 1332 1-2 25-50 65 450 0.23 1.65 0.04 0.05 0.40 G#12 13H # 1H 65 450 0.26 1.35 0.04 0.05 0.40 GTABLE 2 Chemical RequirementsA(Heat Analysis)Diameter, Thickness,or DistanceBetween ParallelFa

29、ces, in. mmPlates and BarsStructuralShapeFlange orLegThickness,in. mmGrade Carbon,max, % Manganese,Bmax, % Phosphorus,Imax, %Sulfur,Imax,%SiliconPlates to 112 in. 40mm Thick,Shapes withFlange or LegThickness to 3 in.75 mm inclusive,Sheet Piling,Bars, Zees, andRolled TeesCPlates Over 112 in.40 mm Thi

30、ck andShapes with FlangeThicknessOver 3 in.75 mmmax, % range, %6 150 all 42 290 0.21 1.35D 0.030 0.030 0.40 0.150.404 100E all 50 345 0.23 1.35D 0.030 0.030 0.40 0.150.402 50F all 55 380 0.25 1.35D 0.030 0.030 0.40 0.15-0.40114 32F #2 50 60 415 0.26 1.35D 0.030 0.030 0.40 G12 114 1332 12 2550 65 450

31、 0.23 1.65 0.030 0.030 0.40 G#12 13H # 1 65 450 0.26 1.35 0.030 0.030 0.40 GA Copper when specified shall have a minimum content of 0.20 % by heat analysis (0.18 % by product analysis).B Manganese, minimum, by heat analysis of 0.80 % (0.75 % by product analysis) shall be required for all plates over

32、 38 in. 10 mm in thickness; a minimum of 0.50 %(0.45 % by product analysis) shall be required for plates 38 in. 10 mm and less in thickness, and for all other products. The manganese to carbon ratio shall not be lessthan 2 to 1.C Bars over 112 in. 40 mm in diameter, thickness, or distance between pa

33、rallel faces shall be made by a killed steel practice.D For each reduction of 0.01 percentage point below the specified carbon maximum, an increase of 0.06 percentage point manganese above the specified maximum ispermitted, up to a maximum of 1.60 %.E Round bars up to and including 11 in. 275 mm in

34、diameter are permitted.F Round bars up to and including 312 in. 90 mm in diameter are permitted.G The size and grade is not described in this specification.H An alternative chemical requirement with a maximum carbon of 0.21 % and a maximum manganese of 1.65 % is permitted, with the balance of the el

35、ements as shownin Table 2Table 2. .I A maximum phosphorus content of 0.04 % and a maximum sulfur content of 0.05 % are permitted for the following materials: Structural shapes Sheet piling Bars Plates with widths up to and including 15 in. 380 mmA572/A572M 153SUPPLEMENTARY REQUIREMENTSSupplementary

36、requirements shall not apply unless specified in the order or contract. Standardizedsupplementary requirements for use at the option of the purchaser are listed in Specification A6/A6M.Those that are considered suitable for use with this specification are listed by title:S5. Charpy V-Notch Impact Te

37、st.S18. Maximum Tensile StrengthS30. Charpy V-Notch Impact Test for Structural Shapes: Alternate Core LocationS32. Single Heat Bundles.In addition, the following supplementary requirements are suitable for use:S81. Tensile StrengthS81.1 For Grade 50 345 steel of thicknesses 34 in. 20 mm and less, th

38、e tensile strength shall be a minimum of 70 ksi 485MPa.TABLE 3 Alloy ContentTypeA Elements HeatAnalysis, %1 Columbium 0.0050.05B2 Vanadium 0.010.15C3 ColumbiumVanadiumColumbium plus vanadium0.005-0.05B0.010.15C0.020.15D5 TitaniumNitrogenVanadium0.006-0.040.0030.0150.06 maxA Alloy content shall be in

39、 accordance with Type 1, 2, 3, or 5 and the contents ofthe applicable elements shall be reported on the test report.B Product analysis limits = 0.004 to 0.06 %.C Product analysis limits = 0.005 to 0.17%D Product analysis limits = 0.01 to 0.16 %.TABLE 4 Tensile RequirementsAGradeYield Point, min Tens

40、ile Strength, min Minimum Elonga-tion, % B,C,Dksi MPa ksi MPa in 8 in.200 mm in 2 in.50 mm42 290 42 290 60 415 20 2450 345 50 345 65 450 18 2155 380 55 380 70 485 17 2060 415 60 415 75 520 16 1865 450 65 450 80 550 15 17A See specimen Orientation under the Tension Tests section of SpecificationA6/A6

41、M.B Elongation not required to be determined for floor plate.C For wide flange shapes over 426 lb/ft 634 kg/m, elongation in 2 in. 50 mm of19 % minimum applies.D For plates wider than 24 in. 600 mm, the elongation requirement is reduced twopercentage points for Grades 42, 50, and 55 290, 345, and 38

42、0, and threepercentage points for Grades 60 and 65 415 and 450. See elongation require-ment adjustments in the Tension Tests section of Specification A6/A6M.A572/A572M 154S90. TypeS90.1 The specific type of steel shall be as specified by the purchaser in the order or contract.S99. Interlock Strength

43、S99.1 The minimum strength of the interlocked joint required for certain services may be specified for straight web (PS type)and arched web (PSA type) sheet piling sections subject to specific agreement between the material purchaser and themanufacturer.SUMMARY OF CHANGESCommittee A01 has identified

44、 the location of selected changes to this standard since the last issue(A572/A572M 13A572/A572M) 13a) that may impact the use of this standard. (Approved Nov. 1,2013.)March 1, 2015.)(1) Revised S99.1 to add type of sheet piling sectionsphosphorus and sulfur levels for wide plates in Table 2where int

45、erlockstrength supplement would applyCommittee A01 has identified the location of selected changes to this standard since the last issue(A572/A572M 12a) that may impact the use of this standard. (Approved Oct. 1, 2013.)(1) Added Supplementary Requirement S99.(2) Revised Table 3.Committee A01 has ide

46、ntified the location of selected changes to this standard since the last issue(A572/A572M 12A572/A572M 13) that may impact the use of this standard. (Approved Nov. 1, 2012Nov.1, 2013.)(1) Revised 4.1 to allow killed steel only.S99.1 to add type of sheet piling sections where interlock strength suppl

47、ement wouldapply.(2) Revised Table 3 to remove a footnote on Columbium restrictions and to remove information on non-killed steels.Committee A01 has identified the location of selected changes to this standard since the last issue(A572/A572M 07A572/A572M 12a) that may impact the use of this standard

48、. (Approved May 1, 2012Oct.1, 2013.)(1) Added Supplementary Requirement S99.(2) Revised Table 3Section .7 to eliminate redundant language.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this st

49、andard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,