ASTM A573 A573M-2013 Standard Specification for Structural Carbon Steel Plates of Improved Toughness《改良韧性的结构碳钢钢板的标准规格》.pdf

1、Designation: A573/A573M 05 (Reapproved 2009)A573/A573M 13Standard Specification forStructural Carbon Steel Plates of Improved Toughness1This standard is issued under the fixed designation A573/A573M; the number immediately following the designation indicates the yearof original adoption or, in the c

2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope Scope*1.1 This specification covers structural quality carbon-manganese-silicon steel plates

3、 in three tensile strength ranges intendedprimarily for service at atmospheric temperatures where improved notch toughness is important.1.2 Plates covered by this specification are limited to a maximum thickness of 1.5 in. 40 mm.1.3 If the steel is to be welded, it is presupposed that a welding proc

4、edure suitable for the grade of steel and intended use orservice will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI unitsare shown in

5、brackets. The values stated in each system are not exact equivalents; therefore, each system is to be usedindependently of the other without combining values in any way.2. Referenced Documents2.1 ASTM Standards:2A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates,

6、Shapes, and Sheet Piling3. General Requirements for Delivery3.1 Plates furnished under this specification shall conform to the requirements of the current edition of Specification A6/A6M,unless a conflict exists in which case this specification shall prevail.4. Materials and Manufacture4.1 The steel

7、 shall be made to fine grain practice.5. Chemical Composition5.1 The heat analysis shall conform to the requirements given in Table 1.5.2 The product analysis shall conform to the requirements given in Table 1 subject to the product analysis tolerances inSpecification A6/A6M.6. Tension Test6.1 The p

8、lates, as represented by the tension test specimens, shall conform to the tensile requirements given in Table 2.7. Keywords7.1 carbon steel; plates; structural steel; toughness; welded construction1 This specification is under the jurisdiction ofASTM Committee A01 on Steel, Stainless Steel and Relat

9、edAlloys and is the direct responsibility of Subcommittee A01.02on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.Current edition approved Oct. 1, 2009Nov. 15, 2013. Published December 2009November 2013. Originally approved in 1966. Last previous edition approved in 20052009as A573

10、/A573M 05.A573/A573M 05 (2009). DOI: 10.1520/A0573_A0573M-05R09. 10.1520/A0573_A0573M-13.2 For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summa

11、ry page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends

12、that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, Wes

13、t Conshohocken, PA 19428-2959. United States1SUPPLEMENTARY REQUIREMENTSStandardized supplementary requirements for use at the option of the purchaser are listed inSpecification A6/A6M. Supplementary requirements shall not apply unless specified in the purchaseorder or contract.SUMMARY OF CHANGESComm

14、ittee A01 has identified the location of selected changes to this standard since the last issue(A573/A573M 05 (2009) that may impact the use of this standard. (Approved Nov. 15, 2013.)(1) Modified phosphorus and sulfur limits in Table 1.TABLE 1 Chemical Requirements (Heat Analysis)colwidth=“21.47*“/

15、COLSPEC Composition, %Grade 58400Grade 65450Grade 70485Carbon, max:12 in. 13 mm and under 0.23 0.24 0.27Over 12 in. 13 mm to 112in.,40 mm, incl0.23 0.26 0.28ManganeseA 0.600.90 0.851.20 0.851.20Phosphorus, max 0.035 0.035 0.035Phosphorus, max 0.030 0.030 0.030Sulfur, max 0.04 0.04 0.04Sulfur, max 0.

16、030 0.030 0.030Silicon 0.100.35 0.150.40 0.150.40A For each reduction of 0.01 percentage point below the specified maximum for carbon, an increase of 0.06 percentage points above the specified maximum formanganese is permitted, up to a maximum of 1.50 % for Grades 58 and 65; and up to a maximum of 1

17、.60 % for Grade 70.TABLE 2 Tensile RequirementsAcolwidth=“22.70*“/COLSPECGrade 58400Grade 65450Grade 70485Tensile strength, ksiMPa587140049065774505307090485620Yield point, min, ksiMPa322203524042290Elongation in 8 in. 200mm minB,C , %21 20 18Elongation in 2 in. 50mm, minB,C , %24 23 21A See the Ori

18、entation subsection in the Tension Tests section of Specification A6/A6M.B Elongation need not be determined for floor plate.C For plates wider than 24 in. 600 mm, the elongation requirement is reduced two percentage points. See the Elongation Requirement Adjustments subsection in theTension Tests s

19、ection of Specification A6/A6M.A573/A573M 132ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, an

20、d the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.Your comments are invited either for revisio

21、n of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you sho

22、uldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).A573/A573M 133