ASTM A706 A706M-2006a Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement.pdf

1、Designation: A 706/A 706M 06aStandard Specification forLow-Alloy Steel Deformed and Plain Bars for ConcreteReinforcement1This standard is issued under the fixed designation A 706/A 706M; the number immediately following the designation indicates the yearof original adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 GeneralThis specifi

3、cation covers deformed and plainlow-alloy steel bars in cut lengths or coils for concretereinforcement intended for applications where restrictive me-chanical properties and chemical composition are required forcompatibility with controlled tensile property applications or toenhance weldability. The

4、 standard sizes and dimensions ofdeformed bars and their number designations are given inTable 1. The text of this specification references notes andfootnotes that provide explanatory material. These notes andfootnotes, excluding those in tables and figures, shall not beconsidered as requirements of

5、 this specification.1.2 GradeBars are of a single minimum yield strengthlevel: namely, 60 000 psi 420 MPa, designated as Grade 60420.1.3 Plain rounds, in sizes up to and including 212 in. 63.5mm in diameter in coils or cut lengths, when ordered, shall befurnished under this specification. For ductil

6、ity properties(elongation and bending), test provisions of the nearest smallernominal diameter deformed bar size shall apply.1.4 Controlled Tensile PropertiesThis specification limitsmechanical properties (Table 2) to provide the desired yield/tensile properties for controlled tensile property appli

7、cations.1.5 WeldingThis specification limits chemical composi-tion (6.2) and carbon equivalent (6.4) to enhance the weldabil-ity of the material. When steel is to be welded, a weldingprocedure suitable for the chemical composition and intendeduse or service should be used. The use of the latest edit

8、ion ofANSI/AWS D1.4 is recommended. This document describesthe proper selection of the filler metals, preheat/interpasstemperatures, as well as, performance and procedure qualifi-cation requirements.1.6 This specification is applicable for orders in eitherinch-pound units (Specification A 706) or in

9、 SI units Specifi-cation A 706M.1.7 The values stated in either inch-pound units or SI unitsare to be regarded as standard. Within the text, the SI units areshown in brackets. The values stated in each system are notexact equivalents; therefore, each system must be used inde-pendently of the other.

10、Combining values from the two systemsmay result in nonconformance with this specification.2. Referenced Documents2.1 ASTM Standards:2A 6/A 6M Specification for General Requirements forRolled Structural Steel Bars, Plates, Shapes, and SheetPilingA 370 Test Methods and Definitions for Mechanical Testi

11、ngof Steel ProductsA 510 Specification for General Requirements for WireRods and Coarse Round Wire, Carbon SteelA 510M Specification for General Requirements for WireRods and Coarse Round Wire, Carbon Steel MetricA 615/A 615M Specification for Deformed and PlainCarbon-Steel Bars for Concrete Reinfor

12、cementA 700 Practices for Packaging, Marking, and LoadingMethods for Steel Products for ShipmentA 706/A 706M Specification for Low-Alloy Steel De-formed and Plain Bars for Concrete ReinforcementA 751 Test Methods, Practices, and Terminology forChemical Analysis of Steel ProductsE29 Practice for Usin

13、g Significant Digits in Test Data toDetermine Conformance with Specifications2.2 ANSI/AWS Standard:AWS D1.4 Structural Welding CodeReinforcing Steel32.3 Government Standards:MIL-STD-129 Marking for Shipment and Storage41This specification is under the jurisdiction of ASTM Committee A01 on Steel,Stai

14、nless Steel, and Related Alloys and is the direct responsibility of SubcommitteeA01.05 on Steel Reinforcement.Current edition approved May 1, 2006. Published May 2006. Originallyapproved in 1974. Last previous edition approved in 2006 as A 706/A 706M 06.2For referenced ASTM standards, visit the ASTM

15、 website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from the American Welding Society, P.O. Box 351040, 550 N.W. LeJeune Rd., Miami, FL 33126.4Avail

16、able from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS. Or visit: http:/assist.daps.dla.mil/online.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700

17、, West Conshohocken, PA 19428-2959, United States.2.4 U.S. Federal Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 deformations, ntransverse protrusions on a de-formed bar.3.1.2 deformed bar, nsteel bar with prot

18、rusions; a barthat is intended for use as reinforcement in reinforced concreteand related construction.3.1.3 DiscussionThe surface of the bar is provided withlugs or protrusions that inhibit longitudinal movement of thebar relative to the concrete surrounding the bar in suchconstruction. The lugs or

19、 protrusions conform to the provisionsof this specification.3.1.4 plain bar, nsteel bar without protrusions.3.1.5 rib, n longitudinal protrusions on a deformed bar.4. Ordering Information4.1 It shall be the responsibility of the purchaser to specifyall requirements that are necessary for material or

20、dered to thisspecification. Such requirements shall include, but are notlimited to, the following:4.1.1 Quantity (weight) mass,4.1.2 Name of material (low-alloy steel deformed and plainbars for concrete reinforcement),4.1.3 Size,4.1.4 Cut lengths or coils,4.1.5 Deformed or plain,4.1.6 Packaging (see

21、 Section 17),4.1.7 ASTM designation and year of issue.5. Material and Manufacture5.1 The bars shall be processed from properly identifiedheats of mold cast or strand cast steel.5.2 The steel shall be made by one of the followingprocesses: electric-furnace, basic-oxygen, or open-hearth.6. Chemical Co

22、mposition6.1 The chemical analysis of each heat shall be determinedin accordance with Test Methods A 751. The manufacturershall make the analysis on test samples taken preferably duringthe pouring of the heat. The percentages of carbon, manganese,phosphorus, sulfur, silicon, copper, nickel, chromium

23、, molyb-denum, and vanadium shall be determined.6.2 The chemical composition as shown by heat analysisshall be limited by the following:Element max, %CarbonManganese0.301.50Phosphorus 0.035Sulfur 0.045Silicon 0.506.3 Choice and use of alloying elements, combined withcarbon, phosphorus, and sulfur to

24、 give the mechanical proper-ties prescribed in Table 2 and Table 3, shall be made by themanufacturer. Elements commonly used include manganese,silicon, copper, nickel, chromium, molybdenum, vanadium,columbium, titanium, and zirconium.6.4 The heat analysis shall be such as to provide a carbonequivale

25、nt (C.E.) not exceeding 0.55 % as calculated by thefollowing formula:C.E. 5 %C 1%Mn61%Cu401%Ni201%Cr102%Mo502%V10(1)TABLE 1 Deformed Bar Designation Numbers, Nominal Weights Masses, Nominal Dimensions, and Deformation RequirementsBarDesig-nationNo.ANominal Weight, lb/ftNominal Mass,kg/mNominal Dimen

26、sionsBDeformation Requirements, in. mmDiameter,in. mmCross-Sectional Areain.2mm2Perimeter,in. mmMaximum AverageSpacingMinimum AverageHeightMaximum Gap(Chord of 12.5 % ofNominal Perimeter)3 10 0.376 0.560 0.375 9.5 0.11 71 1.178 29.9 0.262 6.7 0.015 0.38 0.143 3.64 13 0.668 0.994 0.500 12.7 0.20 129

27、1.571 39.9 0.350 8.9 0.020 0.51 0.191 4.95 16 1.043 1.552 0.625 15.9 0.31 199 1.963 49.9 0.437 11.1 0.028 0.71 0.239 6.16 19 1.502 2.235 0.750 19.1 0.44 284 2.356 59.8 0.525 13.3 0.038 0.97 0.286 7.37 22 2.044 3.042 0.875 22.2 0.60 387 2.749 69.8 0.612 15.5 0.044 1.12 0.334 8.58 25 2.670 3.973 1.000

28、 25.4 0.79 510 3.142 79.8 0.700 17.8 0.050 1.27 0.383 9.79 29 3.400 5.060 1.128 28.7 1.00 645 3.544 90.0 0.790 20.1 0.056 1.42 0.431 10.910 32 4.303 6.404 1.270 32.3 1.27 819 3.990 101.3 0.889 22.6 0.064 1.63 0.487 12.411 36 5.313 7.907 1.410 35.8 1.56 1006 4.430 112.5 0.987 25.1 0.071 1.80 0.540 13

29、.714 43 7.65 11.38 1.693 43.0 2.25 1452 5.32 135.1 1.185 30.1 0.085 2.16 0.648 16.518 57 13.60 20.24 2.257 57.3 4.00 2581 7.09 180.1 1.58 40.1 0.102 2.59 0.864 21.9ABar numbers are based on the number of eighths of an inch included in the nominal diameter of the bars bar numbers approximate the numb

30、er of millimetres of thenominal diameter of the bar.BThe nominal dimensions of a deformed bar are equivalent to those of a plain round bar having the same weight mass per foot metre as the deformed bar.TABLE 2 Tensile RequirementsTensile strength, min, psi MPa 80 000 550AYield strength, min, psi MPa

31、 60 000 420Yield strength, max, psi MPa 78 000 540Elongation in 8 in. 203.2 mm, min, %Bar Designation Nos.3, 4, 5, 6 10, 13, 16, 19 147, 8, 9, 10, 11 22, 25, 29, 32, 36 1214, 18 43, 57 10ATensile strength shall not be less than 1.25 times the actual yield strength.TABLE 3 Bend Test RequirementsBar D

32、esignation No. Pin Diameter for 180 Bend Tests3, 4, 5 10, 13, 16 3dA6, 7, 8 19, 22, 25 4d9, 10, 11 29, 32, 36 6d14, 18 43, 57 8dAd = nominal diameter of specimen.A 706/A 706M 06a26.5 Product (Check) Verification AnalysisAproduct checkanalysis made by the purchaser shall not exceed the followingperce

33、ntages:Element max, %CarbonManganese0.33 %1.56 %Phosphorus 0.043 %Sulfur 0.053 %Silicon 0.55 %7. Requirements for Deformations7.1 Deformations shall be spaced along the bar at substan-tially uniform distances. The deformations on opposite sides ofthe bar shall be similar in size, shape, and pattern.

34、7.2 The deformations shall be placed with respect to the axisof the bar so that the included angle is not less than 45. Wherethe line of deformations forms an included angle with the axisof the bar from 45 to 70, inclusive, the deformations shallreverse alternately in direction on each side, or thos

35、e on oneside shall be reversed in direction from those on the oppositeside. Where the line of deformation is over 70, a reversal indirection shall not be required.7.3 The average spacing or distance between deformationson each side of the bar shall not exceed710 of the nominaldiameter of the bar.7.4

36、 The overall length of deformations shall be such that thegap (measured as a chord) between the ends of the deforma-tions shall not exceed 12.5 % of the nominal perimeter of thebar. Where the ends terminate in a rib, the width of the rib shallbe considered as the gap between these ends. The summatio

37、nof the gaps shall not exceed 25 % of the nominal perimeter ofthe bar. Furthermore, the summation of gaps shall not exceed25 % of the nominal perimeter of the bar. The nominalperimeter of the bar shall be 3.1416 times the nominaldiameter.7.5 The spacing, height, and gap of deformations shallconform

38、to the requirements prescribed in Table 1.8. Measurements of Deformations8.1 The average spacing of deformations shall be deter-mined by measuring the length of a minimum of 10 spaces anddividing that length by the number of spaces included in themeasurement. The measurement shall begin from a point

39、 on adeformation at the beginning of the first space to a correspond-ing point on a deformation after the last included space.Spacing measurements shall not be made over a bar areacontaining bar marking symbols involving letters or numbers.8.2 The average height of deformations shall be determinedfr

40、om measurements made on not less than two typical defor-mations. Determinations shall be based on three measurementsper deformation, one at the center of the overall length and theother two at the quarter points of the overall length.8.3 Insufficient height, insufficient circumferential cover-age, o

41、r excessive spacing of deformations shall not constitutecause for rejection unless it has been clearly established bydeterminations on each lot (see Note 1) tested that typicaldeformation height, gap, or spacing do not conform to theminimum requirements prescribed in Section 7. No rejectionshall be

42、made on the basis of measurements if fewer than tenadjacent deformations on each side of the bar are measured.NOTE 1As used within the intent of 8.3, the term “lot” shall mean allthe bars of one bar size and pattern of deformations contained in anindividual shipping release or shipping order.9. Mech

43、anical Requirements9.1 Tensile Properties:9.1.1 The material, as represented by the test specimens,shall conform to the requirements for tensile properties pre-scribed in Table 2. The yield strength or yield point shall bedetermined by one of the following methods:9.1.1.1 Extension under load using

44、an autographic diagrammethod or an extensometer as described in Test Methods andDefinitions A 370. However, the extension under load shall be0.0035 in./in. 0.0035 mm/mm (0.35 %). When material isfurnished in coils, the test sample shall be straightened prior toplacing it in the jaws of the tensile m

45、achine (see Note 2).Straightening shall be done carefully to avoid the formation oflocal sharp bends and to minimize cold work. Insufficientstraightening prior to attaching the extensometer can result inlower-than-actual yield strength readings.9.1.1.2 By the drop of the beam or halt in the gage of

46、thetesting machine, where the steel tested has a sharp-kneed orwell-defined type of yield point.9.1.2 The percentage of elongation shall be as prescribed inTable 2.NOTE 2Straightening should be done carefully to avoid the formationof local sharp bends and to minimize cold work. Insufficient straight

47、eningprior to attaching the extensometer can result in lower-than-actual yieldstrength readings.9.2 Bending Properties:9.2.1 The bend test specimen shall withstand being bentaround a pin without cracking on the outside radius of the bentportion. The requirements for degree of bending and sizes ofpin

48、s are prescribed in Table 3. When material is furnished incoils, the test sample shall be straightened prior to placing it inthe bend tester.9.2.2 The bend test shall be made on specimens of sufficientlength to ensure free bending and with apparatus that provides:9.2.2.1 Continuous and uniform appli

49、cation of forcethroughout the duration of the bending operation,9.2.2.2 Unrestricted movement of the specimen at points ofcontact with the apparatus and bending around a pin free torotate,9.2.2.3 Close wrapping of the specimen around the pinduring the bending operation.9.3 Test Specimens:9.3.1 The te