ASTM A739-1990a(2016) Standard Specification for Steel Bars Alloy Hot-Wrought for Elevated Temperature or Pressure-Containing Parts or Both《高温件 承压件或高温承压件用热锻合金钢棒材的标准规格》.pdf

1、Designation: A739 90a (Reapproved 2016)Standard Specification forSteel Bars, Alloy, Hot-Wrought, for Elevated Temperature orPressure-Containing Parts, or Both1This standard is issued under the fixed designation A739; the number immediately following the designation indicates the year oforiginal adop

2、tion or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defens

3、e.1. Scope1.1 This specification2covers hot-wrought, ferritic alloysteel bars for elevated temperature or pressure-containing partssuitable for fusion welding or both.1.2 The bars are furnished in the following grades:Grade B 11: 1.25 % chromium, 0.55 % molybdenumGrade B 22: 2.25 % chromium, 1.00 %

4、molybdenum1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:3A29/A29M Specification for Gener

5、al Requirements for SteelBars, Carbon and Alloy, Hot-WroughtA370 Test Methods and Definitions for Mechanical Testingof Steel Products3. Ordering Information3.1 Orders for material under this specification shouldinclude the following information:3.1.1 Quantity (weight or number of pieces),3.1.2 Name

6、of material (ferritic alloy steel bars),3.1.3 Condition (hot wrought, normalized and tempered,machine straightened and descaled),3.1.4 Dimensions (cross-sectional shape, size, and length),3.1.5 ASTM designation and date of issue,3.1.6 Grade (Table 1),3.1.7 Additions to the specification, and3.1.8 En

7、d use.NOTE 1A typical description is as follows: 10 000 lb, Ferritic AlloySteel Bars, Hot Wrought Normalized and Tempered, and Descaled,1.000-in. diameter by 10 ft, ASTM A739 dated_, Grade B11, SpecialStraightened, Special Machined Fittings.4. Materials and Manufacture4.1 Melting PracticeThe steel s

8、hall be made by one ormore of the following primary processes: open-hearth, basic-oxygen, or electric-furnace. The primary melting may incor-porate separate degassing or refining and may be followed bysecondary melting using electroslag remelting or vacuum arcremelting. Where secondary melting is em

9、ployed, the heatshall be defined as all of the ingots remelted from a singleprimary heat.4.2 ConditionUnless otherwise specified, bars shall be hotwrought, heat treated, and descaled.4.3 Heat Treatment:4.3.1 The bars shall be normalized and tempered.4.3.2 Austenitizing temperature shall be within th

10、e rangefrom 1700 to 1800F (927 to 982C).4.3.3 Cooling from the austenitizing temperature may beaccomplished by cooling in still air or moving air, at theproducers option. When permitted by the purchaser, coolingfrom the austenitizing temperature may be accelerated by sprayor liquid quenching.4.3.4 T

11、he minimum tempering temperature shall be 1200F(649C) for Grade B11 and 1250F (677C) for Grade B22.5. Chemical Composition5.1 The heat analysis shall conform to the limits for chemi-cal composition specified in Table 1 for the grade ordered.6. Mechanical Properties6.1 Tensile RequirementsThe bars as

12、 represented by thetest specimens shall conform to the tensile requirementsspecified in Table 2.6.2 SpecimensTension test specimens shall be taken lon-gitudinally and machined from the locations specified in TestMethods and Definitions A370.1This specification is under the jurisdiction of ASTM Commi

13、ttee A01 on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.15 on Bars.Current edition approved Sept. 1, 2016. Published September 2016. Originallyapproved in 1976. Last previous edition approved in 2012 as A739 90a (2012).DOI: 10.1520/A0739-90AR16.2For A

14、SME Boiler and Pressure Vessel Code applications see related Specifi-cation SA-739 in Section II of that code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the st

15、andards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.3 Number of Tests:6.3.1 Two tension tests shall be made to represent bars ofthe same size from each heat in each heat treatment charge.

16、 Forcontinuous heat-treated material, not fewer than two tensiontests shall represent a lot selected on the basis of one tensiontest from each 10 000 lb (4500 kg).6.3.2 When heat treated without interruption in continuousfurnaces, the material in a lot shall be from the same heat, sameprior conditio

17、n, same size, and subjected to the same heattreatments.6.4 Test MethodsTension tests shall be made in accor-dance with Test Methods and Definitions A370. The yieldstrength shall be determined by the 0.2 % offset method.7. Workmanship, Finish, and Appearance7.1 WorkmanshipThe bars shall be free of pi

18、pe, cracks,and flakes. Within the limits of good manufacturing andinspection practices the bars shall be free of injurious seams,laps, segregation, or other imperfections which, due to theirnature, degree or extent, will interfere with the use of thematerial in machining or fabrication.7.2 Descaling

19、Unless otherwise specified, the bars shall bedescaled.8. General Requirements8.1 Material furnished under this specification shall con-form to the applicable requirements of the current edition ofSpecification A29/A29M.9. Certification and Test Reports9.1 A manufacturers certification that the mater

20、ial wasmanufactured and tested in accordance with this specificationtogether with a report of the analysis and tension test resultsshall be furnished at the time of shipment. The report shallinclude the name of the manufacturer, ASTM designationnumber and year date and revision letter, if any, grade

21、, heatnumber, and size.10. Product Marking10.1 The bars shall be marked in accordance with Specifi-cation A29/A29M except as modified or supplemented by 10.2through 10.4 of this specification.10.2 When specified by the purchaser, the heat number shallbe permanently stamped on one end of each bar 2.5

22、0 in. andlarger in nominal diameter (or equivalent cross-sectional area).10.3 The bars shall neither be hot nor cold stamped on thesides unless approved by the purchaser on the purchase order.10.4 Each lift, regardless of size, shall be tagged with theinformation required by Specification A29/A29M.1

23、1. Keywords11.1 alloy steel bars; high-temperature applications; hot-wrought steel bars; pressure-containing parts; steel bars; tem-perature service applicationhighASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this

24、standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be r

25、eviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of therespon

26、sible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West

27、 Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission right

28、s to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Chemical RequirementsElementComposition, %Grade B 11 Grade B 22Carbon, max 0.050.20 0.050.15Manganese 0.400.65 0.300.60Phosphorus, max 0.035 0.035S

29、ulfur, max 0.040 0.040Silicon 0.500.80 0.50 maxChromium 1.001.50 2.002.50Molybdenum 0.450.65 0.901.10TABLE 2 Tensile RequirementsGrade B 11 Grade B 22Tensile strength, ksi (MPa) 70.095.0 (483655) 75.095.0 (517655)Yield strength, min, ksi (MPa) 45.0 (310) 45.0 (310)Elongation in 2 in. or 50 mm,min, %18 18Reduction of area, min, % 45 45A739 90a (2016)2