ASTM A790 A790M-2010 Standard Specification for Seamless and Welded Ferritic Austenitic Stainless Steel Pipe《无缝与焊接铁素体 奥氏体不锈钢管的标准规格》.pdf

1、Designation: A790/A790M 10Standard Specification forSeamless and Welded Ferritic/Austenitic Stainless SteelPipe1This standard is issued under the fixed designation A790/A790M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the yea

2、r of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification2covers seamless and straight-seamwelded ferritic/austenitic steel pipe intended for general c

3、orro-sive service, with particular emphasis on resistance to stresscorrosion cracking. These steels are susceptible to embrittle-ment if used for prolonged periods at elevated temperatures.1.2 Optional supplementary requirements are provided forpipe when a greater degree of testing is desired. These

4、supplementary requirements call for additional tests to be madeand, when desired, one or more of these may be specified in theorder.1.3 Appendix X1 of this specification lists the dimensionsof welded and seamless stainless steel pipe as shown in ANSIB36.19. Pipe having other dimensions may be furnis

5、hedprovided such pipe complies with all other requirements of thisspecification.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. The values stated in eachsystem may not be exact equivalents; the

6、refore, each systemshall be used independently of the other. Combining valuesfrom the two systems may result in non-conformance with thestandard. The inch-pound units shall apply unless the Mdesignation of this specification is specified in the order.NOTE 1The dimensionless designator NPS (nominal p

7、ipe size) hasbeen substituted in this standard for such traditional terms as nominaldiameter, size, and nominal size.2. Referenced Documents2.1 ASTM Standards:3A370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA923 Test Methods for Detecting Detrimental IntermetallicPhase in D

8、uplex Austenitic/Ferritic Stainless SteelsA941 Terminology Relating to Steel, Stainless Steel, Re-lated Alloys, and FerroalloysA999/A999M Specification for General Requirements forAlloy and Stainless Steel PipeE213 Practice for Ultrasonic Testing of Metal Pipe andTubingE309 Practice for Eddy-Current

9、 Examination of Steel Tu-bular Products Using Magnetic SaturationE381 Method of Macroetch Testing Steel Bars, Billets,Blooms, and ForgingsE426 Practice for Electromagnetic (Eddy-Current) Exami-nation of Seamless and Welded Tubular Products, Austen-itic Stainless Steel and Similar AlloysE527 Practice

10、 for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.2 ANSI Standards:4B1.20.1 Pipe Threads, General PurposeB36.10 Welded and Seamless Wrought Steel PipeB36.19 Stainless Steel Pipe2.3 SAE Standard:5SAE J 10862.4 Other Standard:6SNT-TC-1A Personal Qualification and Certification inN

11、ondestructive Testing2.5 AWS StandardA5.9 Corrosion-Resisting Chromium and Chromium-Nickel Steel Welding Rods and Electrodes3. Terminology3.1 DefinitionsFor definitions of terms used in this speci-fication refer to Terminology A941.1This specification is under the jurisdiction of ASTM Committee A01

12、on Steel,Stainless Steel and Related Alloys and is the direct responsibility of SubcommitteeA01.10 on Stainless and Alloy Steel Tubular Products.Current edition approved Oct. 1, 2010. Published November 2010. Originallyapproved in 1981. Last previous edition approved in 2009 as A790/A790M09a.DOI: 10

13、.1520/A0790_A0790M-10.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation SA790 in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume i

14、nformation, refer to the standards Document Summary page onthe ASTM website.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.5Available from Society of Automotive Engineers (SAE), 400 CommonwealthDr., Warrendale, PA 15096-

15、0001, http:/www.sae.org.6Available fromAmerican Society for Nondestructive Testing (ASNT), P.O. Box28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http:/www.asnt.org.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C70

16、0, West Conshohocken, PA 19428-2959, United States.4. Ordering Information4.1 Orders for material under this specification shouldinclude the following, as required, to describe the desiredmaterial adequately:4.1.1 Quantity (feet, metres, or number of lengths),4.1.2 Name of material (ferritic/austeni

17、tic steel pipe),4.1.3 Process (seamless or welded),4.1.4 Grade (see Table 1),4.1.5 Size (NPS designator or outside diameter and sched-ule number of average wall thickness),4.1.6 Length (specific or random) (see Section 11),4.1.7 End finish (section on ends of Specification A999/A999M),4.1.8 Optional

18、 requirements (product analysis, Section 9;hydrostatic test or nondestructive electric test, Section 14),4.1.9 Test report required (section on certification of Speci-fication A999/A999M),4.1.10 Specification designation, and4.1.11 Special requirements and any supplementary require-ments selected.5.

19、 General Requirements5.1 Material furnished under this specification shall con-form to the applicable requirements of the current edition ofSpecification A999/A999M unless otherwise provided herein.6. Materials and Manufacture6.1 Manufacture:6.1.1 The pipe shall be made by the seamless or anautomati

20、c welding process, with no addition of filler metal inthe welding operation.6.1.2 At the manufacturers option, pipe may be eitherhot-finished or cold-finished.6.1.3 The pipe shall be pickled free of scale. When brightannealing is used, pickling is not necessary.TABLE 1 Heat TreatmentUNSDesignationTy

21、peATemperature F C QuenchS31200 1920201010501100Rapid cooling in waterS31260 1870201010201100Rapid cooling in air or waterS31500 180019009801040Rapid cooling in air or waterS31803 1870201010201100Rapid cooling in air or waterS32003 1850205010101120Rapid cooling in air or waterS32101 1870 1020 Quench

22、ed in water or rapidlycooled by other meansS32202 1870197510201080Rapid cooling in air or waterS32205 2205 1870201010201100Rapid cooling in air or waterS32304 2304 170019209251050Rapid cooling in air or waterS32506 1870205010201120Rapid cooling in air or waterS32520 1975205010801120Rapid cooling in

23、air or waterS32550 255 1900 1040 min Rapid cooling in air or waterS32707 1975205010801120Rapid cooling in air or waterS32750 2507 1880206010251125Rapid cooling in air or waterS32760 1960208510701140Rapid cooling in air or waterS32808 1920210010501150Rapid cooling in air or waterS32900 329 1700175092

24、5955Rapid cooling in air or waterS32906 1870210010201150Rapid cooling in air or waterS32950 182018809901025Air coolS33207 1905208510401140Rapid cooling in water or byother meansS39274 1920206010251125Rapid cooling in air or waterS39277 1975215510801180Rapid cooling in air or waterS82011 185020501010

25、1120Rapid cooling in air or waterACommon name, not a trademark, widely used, not associated with any oneproducer. 329 is na AISI number.A790/A790M 1026.2 DiscardA sufficient discard shall be made from eachingot to secure freedom from injurious piping and unduesegregation.6.3 Unless otherwise stated

26、in the order, all pipe shall befurnished in the heat-treated condition as shown in Table 1.6.3.1 For seamless pipe, as an alternate to final heat treat-ment in a continuous furnace or batch-type furnace, immedi-ately following hot forming while the temperature of the pipesis not less than the specif

27、ied minimum solution treatmenttemperature, pipes shall be individually quenched in water orrapidly cooled by other means, except for UNS S32950, whichshall be air cooled.6.3.2 If the purchaser desires pipe without heat treatmentsubsequent to welding, the purchase order shall specify thefollowing con

28、dition:6.3.2.1 No final heat treatment of pipe fabricated from platethat has been heat treated as required by Table 1 for theparticular grade is required, provided a sample of that heat offinished pipe or material representative of that heat of pipe asa prolongation of the weld passes the Test Metho

29、ds A923Method B or C (See Note 2), including base metal, weld metal,and heat affected zone per heat. Each pipe supplied under thisrequirement shall be stenciled with the suffix “HT-O.”6.3.2.2 For materials not listed in Table 3 of Test MethodsA923, the HT-O provision does not apply.NOTE 2The Test Me

30、thods A923 test method (B or C) is at themanufacturers option, unless otherwise specified by the purchaser.7. Chemical Composition7.1 The steel shall conform to the chemical requirements asprescribed in Table 2.8. Heat Analysis8.1 An analysis of each heat of steel shall be made by thesteel manufactu

31、rer to determine the percentages of the ele-ments specified.9. Product Analysis9.1 At the request of the purchasers inspector, an analysisof one billet or one length of flat-rolled stock from each heat,or two pipes from each lot, shall be made by the manufacturer.A lot of pipe shall consist of the f

32、ollowing number of lengthsof the same size and wall thickness from any one heat of steel:NPS Designator Lengths of Pipe in LotUnder 2 400 or fraction thereof2 to 5, incl 200 or fraction thereof6 and over 100 or fraction thereof9.2 The results of these analyses shall be reported to thepurchaser or th

33、e purchasers representative and shall conformto the requirements specified in Section 7.9.3 If the analysis of one of the tests specified in 8.1 or 9.1does not conform to the requirements specified in Section 7,ananalysis of each billet or pipe from the same heat or lot may bemade, and all billets o

34、r pipe conforming to the requirementsshall be accepted.TABLE 2 Chemical RequirementsAUNSDesigna-tionBTypeCC Mn P S Si Ni Cr Mo N Cu OthersS31200 0.030 2.00 0.045 0.030 1.00 5.56.5 24.026.0 1.202.00 0.140.20 . . . . . .S31260 0.030 1.00 0.030 0.030 0.75 5.57.5 24.026.0 2.53.5 0.100.30 0.200.80 W0.100

35、.50S31500 0.030 1.202.00 0.030 0.030 1.402.00 4.25.2 18.019.0 2.503.00 0.050.10 . . . . . .S31803 0.030 2.00 0.030 0.020 1.00 4.56.5 21.023.0 2.53.5 0.080.20 . . . . . .S32003 0.030 2.00 0.030 0.020 1.00 3.04.0 19.5-22.5 1.502.00 0.140.20 . . . . . .S32101 0.040 4.06.0 0.040 0.030 1.00 1.351.70 21.0

36、22.0 0.100.80 0.200.25 0.100.80 . . .S32202 0.030 2.00 0.040 0.010 1.00 1.002.80 21.524.0 0.45 0.180.26 . . . . . .S32205 2205 0.030 2.00 0.030 0.020 1.00 4.56.5 22.023.0 3.03.5 0.140.20 . . . . . .S32304 2304 0.030 2.50 0.040 0.040 1.00 3.05.5 21.524.5 0.050.60 0.050.20 0.050.60 . . .S32506 0.030 1

37、.00 0.040 0.015 0.90 5.57.2 24.026.0 3.03.5 0.080.20 . . . W0.050.30S32520 0.030 1.5 0.035 0.020 0.80 5.58.0 24.026.0 3.05.0 0.200.35 0.53.00 . . .S32550 255 0.04 1.50 0.040 0.030 1.00 4.56.5 24.027.0 2.93.9 0.100.25 1.502.50 . . .S32707 0.030 1.50 0.035 0.010 0.50 5.59.5 26.029.0 4.05.0 0.300.50 1.

38、0 Co0.52.0S32750 2507 0.030 1.20 0.035 0.020 0.80 6.08.0 24.026.0 3.05.0 0.240.32 0.5 . . .S32760 0.05 1.00 0.030 0.010 1.00 6.08.0 24.026.0 3.04.0 0.200.30 0.501.00 W0.501.0040 minDS32808 0.030 1.10 0.030 0.010 0.50 7.08.2 27.027.9 0.801.20 0.300.40 . . . W2.102.50S32900 329 0.08 1.00 0.040 0.030 0

39、.75 2.55.0 23.028.0 1.002.00 . . . . . . . . .S32906 0.030 0.801.50 0.030 0.030 0.80 5.87.5 28.030.0 1.502.60 0.300.40 0.80 . . .S32950 0.030 2.00 0.035 0.010 0.60 3.55.2 26.029.0 1.002.50 0.150.35 . . . . . .S33207 0.030 1.50 0.035 0.010 0.80 6.09.0 29.033.0 3.05.0 0.400.60 1.0S39274 0.030 1.00 0.0

40、30 0.020 0.80 6.08.0 24.026.0 2.53.5 0.240.32 0.200.80 W1.502.50S39277 0.025 0.80 0.025 0.002 0.80 6.58.0 24.026.0 3.04.0 0.230.33 1.202.00 W 0.81.2S82011 0.030 2.03.0 0.040 0.020 1.00 1.002.00 20.523.5 0.101.00 0.150.27 0.50 . . .AMaximum, unless a range or minimum is indicated. Where ellipses (.)

41、appear in this table, there is no minimum and analysis for the element need not be determinedor reported.BNew designation established in accordance with Practice E527 and SAE J 1086.CCommon name, not a trademark, widely used, not associated with any one producer. 329 is na AISI number.D%Cr+3.33 %Mo+

42、163 %N.A790/A790M 10310. Tensile and Hardness Properties10.1 The material shall conform to the tensile and hardnessproperties prescribed in Table 3.11. Lengths11.1 Pipe lengths shall be in accordance with the followingregular practice:11.1.1 Unless otherwise agreed upon, all sizes from NPS18to and i

43、ncluding NPS 8 are available in a length up to 24 ft (seeNote 3) with the permissible range of 15 to 24 ft (see Note 3).Short lengths are acceptable and the number and minimumlength shall be agreed upon between the manufacturer and thepurchaser.NOTE 3This value applies when the inch-pound designatio

44、n of thisspecification is the basis of purchase. When the M designation of thisspecification is the basis of purchase, the corresponding metric value(s)shall be agreed upon between the manufacturer and purchaser.11.1.2 If definite cut lengths are desired, the lengths re-quired shall be specified in

45、the order. No pipe shall be less thanthe specified length and no more than14 in. 6 mm over it.11.1.3 No jointers are permitted unless otherwise specified.12. Workmanship, Finish, and Appearance12.1 The finished pipes shall be reasonably straight andshall have a workmanlike finish. Imperfections may

46、be re-moved by grinding, provided the wall thicknesses are notTABLE 3 Tensile and Hardness RequirementsUNSDesignationTypeATensileStrength,min, ksiMPaYieldStrength,min,ksi MPaElongationin 2 in. or50 mm,min, %Hardness, maxHBW HRCS31200 100 690 65 450 25 280 . . .S31260 100 690 65 450 25 . . . . . .S31

47、500 92 630 64 440 30 290 30S31803 90 620 65 450 25 290 30S32003 95 655 65 450 25 290 30S32101t #0.187 in.5.00 mm101 700 77 530 30 290 . . .t0.187 in.5.00 mm94 650 65 450 30 290 . . .S32202 94 650 65 450 30 290 30S32205 2205 95 655 65 450 25 290 30S32304 2304 87 600 58 400 25 290 30S32506 90 620 65 4

48、50 18 302 32S32520 112 770 80 550 25 310 . . .S32550 255 110 760 80 550 15 297 31S32707 133 920 101 700 25 318 34S32750 2507 116 800 80 550 15 300 32S32760B109 750 80 550 25 300 . . .S32808 116 800 80 550 15 310 32S32900 329 90 620 70 485 20 271 28S32906Wall below0.40 in.10 mm116 800 94 650 25 300 32Wall 0.40 in.10 mmand above109 750 80 550 25 300 32S32950 100 690 70 480 20 290 30S33207Wall below0.157 in. 4 mm138 950 112 770 15 336 36Wall 0.157 in.4 mm and above123 850 101 700 15 336 36S39274 116 800 80 550 15 310 32S39277 120 825 90 620 25 290 3