ASTM B1005-2017 Standard Specification for Copper-Clad Aluminum Bar for Electrical Purposes (Bus Bar)《电气用铜包铝棒(汇流条)的标准规格》.pdf

1、Designation: B1005 17Standard Specification forCopper-Clad Aluminum Bar for Electrical Purposes (BusBar)1This standard is issued under the fixed designation B1005; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last re

2、vision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers copper clad aluminum rectan-gular bar for electrical (bus) applications.1.2 Six classes of copper-c

3、lad aluminum bar are covered asfollows:Class 20ANominal 20 volume % copper, annealed.Class 25ANominal 25 volume % copper, annealed.Class 30ANominal 30 volume % copper, annealed.Class 20HNominal 20 volume % copper, hard-worked.Class 25HNominal 25 volume % copper, hard-worked.Class 30HNominal 30 volum

4、e % copper, hard-worked1.3 The values stated in inch-pound units are to be regardedas the standard, except for resistivity and density, where the SIunits are the standard. The values given in parentheses are forinformation only.1.4 This international standard was developed in accor-dance with intern

5、ationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 The following document

6、s of the issue in effect on dateof material purchase form a part of this specification to theextent referenced herein:2.2 ASTM Standards:2B193 Test Method for Resistivity of Electrical ConductorMaterialsB354 Terminology Relating to Uninsulated Metallic Electri-cal ConductorsE3 Guide for Preparation

7、of Metallographic SpecimensE8/E8M Test Methods for Tension Testing of Metallic Ma-terialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE290 Test Methods for Bend Testing of Material for Ductil-ity3. Terminology3.1 DefinitionsRefer to Terminology B3

8、54 for definitionof product terms used in this specification.4. Ordering Information4.1 Orders for materials to this specification shall includethe following information:4.1.1 This specification designation (which includes thenumber, the year, and the revision letter, if applicable),4.1.2 Quantity i

9、n weight or pieces,4.1.3 Classes, (see 1.2),4.1.4 Edge contour (Section 12),4.1.5 Cross-Sectional Dimensions: Thickness and Width(Section 13),4.2 Additionally, orders for material to this specificationshall include the following information when required by thepurchaser:4.2.1 Whether witness of insp

10、ection by the purchasersrepresentative is required prior to material shipment (Section15),4.2.2 Whether certification is required (Section 17),4.2.3 Whether an alternative tensile sampling selectionprocedure is acceptable (Section 7).5. Manufacture5.1 The products covered by this specification shall

11、 consistof a solid core of aluminum with a continuous outer copperlayer bonded to the core throughout and shall be of such qualitythat the resulting products comply with the requirements in thisspecification.6. Quality Assurance6.1 Responsibility for Inspection and TestsUnless other-wise specified i

12、n the contract or purchase order, the producer isresponsible for the performance of all inspection and test1This specification is under the jurisdiction of ASTM Committee B01 onElectrical Conductors and is the direct responsibility of Subcommittee B01.06 onBi-Metallic Conductors.Current edition appr

13、oved April 1, 2017. Published May 2017. DOI: 10.1520/B1005-17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website

14、.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of Inte

15、rnational Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1requirements specified herein. The producer may use his ownor any other suitable facilities for the performance of theinspection and test requirements specified herein,

16、 unless dis-approved by the purchaser in the order or at the time of contractsigning. The purchaser shall have the right to perform any ofthe inspections and tests set forth in this specification wheresuch inspections are deemed necessary to assure that materialconforms to prescribed requirements.6.

17、2 Lot DefinitionAn inspection of the lot shall consist ofan identifiable quantity of same mill form, and nominaldimensions and subjected to inspection at one time.7. Tensile Properties7.1 LimitsThe material shall conform to the tensile prop-erties in Table 1.7.2 Number of Specimens:7.2.1 For materia

18、l having a nominal weight of less than 1 lb/ft (up through 1.8 kg/linear m), one tension test specimen shallbe taken for each 2000 1b (1000 kg), or fraction thereof, in thelot.7.2.2 For material having a nominal weight of greater than1 lb/ ft (over 1.8 kg/linear m), one tension test specimen shallbe

19、 taken for each 2000 ft (600 m), or fraction thereof, in the lot.7.2.3 One tension test specimen shall be taken from arandom bar representing each 3000 lb of bar, or fractionthereof, of the same temper, thickness, and width in theshipment.7.2.4 Other procedures for selecting samples may be em-ployed

20、 if agreed upon between the producer and the supplier orpurchaser.7.3 The geometry of test specimens and the location in theproduct from which they are taken shall conform to TestMethods E8/E8M.7.4 Test MethodsThe tensile testing shall be in accor-dance with Test Methods E8/E8M.7.5 RetestsWhen there

21、 is evidence that the test specimenis defective or is not representative of the lot of material,retesting shall be performed in accordance with Test MethodsE8/E8M.8. Bend Properties8.1 Limits:8.1.1 Class 20A, 25A and Class 30A bars shall withstand aflatwise bend at room temperature, through an angle

22、 of 90around mandrel having a radius shown in Table 2 withoutcracking or obvious orange peel or evidence of slivers or otherimperfections on the surface (the cladding layer), or blisterphenomenon inside the bending width. In macrostructure, nearthe curved areas, interface holes or cracks should not

23、appear,and no separation phenomenon between the cladding layer andthe aluminum core. For a flatwise bend, the mandrel shall be90 from the rolling direction, and across the greater (width)dimension of the bar. The required 90 bend shall be in therolling direction. This is a longitudinal guided bend a

24、s definedand shown in Test Method E290, Fig. 6.8.2 Number of SpecimensThe number of specimens (testfrequency) shall be the same as for tension tests as required in7.2.8.3 Test SpecimensBend test specimens shall be a fullsection of the material with a minimum length of 13 in. (330mm).8.4 Test Methods

25、Bend tests shall be made in accordancewith Test Method E290.8.5 Bending Result Secondary Test:8.5.1 Removing 1/2 straight segment of at each end of thesamples after the bending test, retain contains 1/2 part ofbending parts, as shown in Fig. 1.8.5.2 Removing the cladding layer on one narrow side of

26、thebending sample contain the bending part, then grind and polishthe section of the remove cladding layer until the aluminumcore exposes according to the provisions of Guide E3.8.5.3 Checking the macrostructure on the section near theinterface.8.5.4 For the requirements of lateral bending property,

27、thebending angle and bending diameter should be indicated in thepurchase order (or contract) with the consultation of the twosides between supply and purchase.TABLE 1 Tensile and Elongation RequirementsCopper Volume%Tensile StrengthElongation, min %in 9.84 in. (250 mm)MinimumH Classesksi (MPa)Maximu

28、mA Classesksi (MPa)HClassesAClasses20 23.2 (160) 18.1 (125) 3 2525 24.6 (170) 18.5 (126) 3.5 2830 26.1 (180) 18.8 (130) 3.8 30TABLE 2 The Diameter of the Bending CylinderThickness,in. (mm)Bending Diameterin. (mm)1.18 (30) to 3.94 (100) 0.032 (0.80)3.94 (100) 0.047 (1.20)Thickness Thickness Tolerance

29、s0.118 (3.0) to 0.236 (6.0) 0.004 (0.10)0.236 (6.0) to 0.394 (10.0) 0.006 (0.15)0.394 (10.0) 0.008 (0.20)TABLE 6 Minimum Copper ThicknessThickness of Productin. (mm)Thickness of Cladding Layerin. (mm)#0.236 (6) 0.008 (0.20)0.236 (6) 0.016 (0.40)B1005 17315.2 When such inspection or witness of inspec

30、tion andtesting is agreed upon, the producer shall afford the purchasersrepresentative all reasonable facilities to satisfy him that thematerial meets the requirements of this specification. Inspec-tion and tests shall be conducted so there is no unnecessaryinterference with the producers operations

31、.16. Rejection and Retest16.1 If any material fails to conform to all of the applicablerequirements of this specification, it shall be cause for rejectionof the inspection lot.16.2 When there is evidence that a failed specimen was notrepresentative of the inspection lot and when no other samplingpla

32、n is provided or approved by the purchaser through thecontract or purchase order, at least two additional specimensshall be selected to replace each test specimen that failed. Allspecimens so selected for retest shall meet the requirements ofthe specification or the lot shall be subject to rejection

33、.16.3 Material in which non-conforming conditions are dis-covered subsequent to inspection may be rejected.16.4 If material is rejected by the purchaser, the producer orsupplier is responsible only for replacement of the material tothe purchaser. As much as possible of the rejected materialshall be

34、returned to the producer or supplier.17. Certification17.1 The producer or supplier shall, upon request, furnish tothe purchaser a certificate stating that the material has beersampled, tested and inspected in accordance with thisspecification, and has met the requirements.18. Packaging and Package

35、Marking18.1 The material shall be packaged to provide adequateprotection during normal handling and transportation and eachpackage shall contain only one size or shape and temper ofmaterial unless otherwise agreed. The type of packing andgross weight of containers shall, unless otherwise agreed, be

36、atthe producer or suppliers discretion, provided they are such asto ensure acceptance by common or other carriers for safetransportation at the lowest rate to the delivery point.19. Keywords19.1 bus bar; copper clad aluminum bar; electricalANNEX(Mandatory Information)A1. THE TEST METHOD OF INTERFACI

37、AL SHEAR STRENGTHA1.1 SampleA1.1.1 Sample length is 3.937 in. (100 mm), sample width(b1) is 0.787 in. (20.00 mm) 60.004 in. (0.10 mm), sampleshear plane width (L1) is 0.157 in. (4.00 mm) 60.004 in. (0.10mm), grooving width is less than 0.079 in. (2 mm). Sample cutby mechanical processing or EDM, dur

38、ing the process theshear plane should not be damaged. And the shape and size ofthe sample is shown in Fig. A1.1.A1.2 The Test SpecimenA1.2.1 The sample is clamped in the universal materialtesting machine, clamping length of the sample is 0.787 in. (20mm), as shown in Fig. A1.2. The universal materia

39、l testingmachine will provide the axial tension to the sample. Theclamp movement speed shall remain under 1.969 in./min (50mm/min), until the shear deformation occurs between the corematerial and cladding layer resulting in complete separation.By means of the records of a force-displacement curve, o

40、r theload recorder (such as a computer), the maximum force (Fmax)added on the sample during the test is achieved.Where:1 = Aluminum core;2 = Cladding layer;3 = Grooving.FIG. A1.1 The Shape and Size of SampleB1005 174A1.3 The Assessment of Test ResultsA1.3.1 The interface shear strength calculated wi

41、th theformula Eq A1.1 and the strength value should not be less than5.8 Ksi (40 MPa). 5FmaxS1(A1.1)where: = interface shear strength, keeping one decimal places,units are kips per square inch;Fmax= maximum shear force, keeping one decimal places,units are pounds;S1= the shear plane area of the sampl

42、e, referring toformula Eq A1.2, keeping two decimal places, unitsare square inch.S15 L13 b1(A1.2)where:L1= shear plane width, keeping two decimal places, unitsare inch;b1= sample width, keeping two decimal places, units areinch.ASTM International takes no position respecting the validity of any pate

43、nt rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision

44、at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comme

45、nts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted

46、 by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-ma

47、il); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ = Fixture;2 = Sample.FIG. A1.2 Schematic Diagram of Test Method of Interface ShearStrengthB1005 175