ASTM B179-2018 Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes.pdf

1、Designation: B179 17B179 18Standard Specification forAluminum Alloys in Ingot and Molten Forms for Castingsfrom All Casting Processes1This standard is issued under the fixed designation B179; the number immediately following the designation indicates the year oforiginal adoption or, in the case of r

2、evision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This speci

3、fication covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture ofcastings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1.NOTE 1Throughout this specification the use of “ingot” in a general sense includ

4、es sow, T-bar, T-ingot, and pig.1.2 Alloy designations are in accordance with ANSI H35.1/H35.1(M).NOTE 2Supplementary data pertaining to the alloys covered by this specification when used in the form of castings are given in SpecificationsB26/B26M, B85/B85M, B108/B108M, B618/B618M, B686/B686M, B955/

5、B955M, and B969/B969M.1.3 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1.1.5 The values stated in inch-pound units

6、are to be regarded as standard. No other units of measurement are included in thisstandard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety, health, and envi

7、ronmental practices and determine the applicability ofregulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardizationestablished in the Decision on Principles for the Development of International Standards,

8、 Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extentreferenced herein:2.2 ASTM Standards:2B2

9、6/B26M Specification for Aluminum-Alloy Sand CastingsB85/B85M Specification for Aluminum-Alloy Die CastingsB108/B108M Specification for Aluminum-Alloy Permanent Mold CastingsB618/B618M Specification for Aluminum-Alloy Investment CastingsB666/B666M Practice for Identification Marking of Aluminum and

10、Magnesium ProductsB686/B686M Specification for Aluminum Alloy Castings, High-StrengthB955/B955M Specification for Aluminum-Alloy Centrifugal CastingsB969/B969M Specification for Aluminum-Alloy Castings Produced by Squeeze Casting, Thixocast and Rheocast Semi-SolidCasting ProcessesB985 Practice for S

11、amplingAluminum Ingots, Billets, Castings and Finished or Semi-Finished WroughtAluminum Products forCompositional Analysis1 This specification is under the jurisdiction of ASTM Committee B07 on Light Metals and Alloys and is the direct responsibility of Subcommittee B07.01 on AluminumAlloy Ingots an

12、d Castings.Current edition approved Oct. 1, 2017May 15, 2018. Published November 2017May 2018. Originally approved in 1946. Last previous edition approved in 20142017 asB179 14.B179 17. DOI: 10.1520/B0179-17.10.1520/B0179-18.2 For referencedASTM standards, visit theASTM website, www.astm.org, or con

13、tactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have be

14、en made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official documen

15、t.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1TABLE 1 Chemical Composition Limits of Aluminum Alloys in Ingot and Molten Forms for All Casting ProcessesA,B,C,DThis T

16、able has been reprinted by the permission of the Aluminum Association, Inc.Only composition limits which are identical to those listed herein or are registered with the Aluminum Association should be designated as “AA” alloys.DESIG.S Si Fe Cu Mn Mg Cr Ni Zn Ti Ag Be Pb Sn Zr FNsOTHERSEAl Min.AANo. E

17、ach TotalFEach TotalF100.1* 0.15 0.60.8 0.10 . . . . . . . . . . . . 0.05 . . . . . . . . . . . . . . . . . . 0.025 Mn+Cr+Ti+V . . . 0.03 0.10 99.00G130.1* . . . . . . 0.10 . . . . . . . . . . . . 0.05 . . . . . . . . . . . . . . . . . . 0.025 Mn+Cr+Ti+V,2.5 min. Fe/Si ratio . . . 0.03 0.10 99.30G15

18、0.1* . . . . . . 0.05 . . . . . . . . . . . . 0.05 . . . . . . . . . . . . . . . . . . 0.025 Mn+Cr+Ti+V,2.0 min. Fe/Si ratio . . . 0.03 0.10 99.50G160.1 0.10 0.25 . . . . . . . . . . . . . . . 0.05 . . . . . . . . . . . . . . . . . . 0.025 Mn+Cr+Ti+V,2.0 min. Fe/Si ratio . . . 0.03 0.10 99.60G170.1*

19、 . . . . . . . . . . . . . . . . . . . . . 0.05 . . . . . . . . . . . . . . . . . . 0.025 Mn+Cr+Ti+V,1.5 min. Fe/Si ratio . . . 0.03 0.10 99.70G201.2 0.10 0.10 4.05.2 0.200.50 0.200.55 . . . . . . . . . 0.150.35 0.401.0 . . . . . . . . . . . . . . . . . . 0.05 0.10 Rem.A201.1 0.05 0.07 4.05.0 0.200.

20、40 0.200.35 . . . . . . . . . 0.150.35 0.401.0 . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.203.2 0.20 0.35 4.85.2 0.200.30 0.10 . . . 1.31.7 0.10 0.150.25 . . . . . . . . . . . .0.100.300.200.30 Co,0.200.30 Sb,0.50 Ti + Zr. . . 0.05 0.20 Rem.204.2 0.15 0.100.20 4.24.9 0.05 0.200.35 . . . 0.03

21、0.05 0.150.25 . . . . . . . . . 0.05 . . . . . . . . . 0.05 0.15 Rem.205.2L 0.07 0.05 4.25.0 . . . 0.250.33 . . . . . . . . . 0.50 0.60.9 . . . . . . . . . . . . . . . . . . 0.08 0.17 Rem.206.2 0.10 0.10 4.25.0 0.200.50 0.200.35 . . . 0.03 0.05 0.150.25 . . . . . . . . . 0.05 . . . . . . . . . 0.05

22、0.15 Rem.A206.2 0.05 0.07 4.25.0 0.200.50 0.200.35 . . . 0.03 0.05 0.150.25 . . . . . . . . . 0.05 . . . . . . . . . 0.05 0.15 Rem.B206.2 0.05 0.07 4.25.0 0.200.50 .200.35 . . . 0.03 0.05 0.05 . . . . . . . . . 0.05 . . . . . . . . . 0.05 0.15 Rem.240.1 0.50 0.40 7.09.0 0.300.7 5.66.5 . . . 0.300.7

23、0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.242.1 0.7 0.8 3.54.5 0.35 1.31.8 0.25 1.72.3 0.35 0.25 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.242.2 0.6 0.6 3.54.5 0.10 1.31.8 . . . 1.72.3 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.A242.1 0.6

24、0.6 3.74.5 0.10 1.31.7 0.15 0.25 1.82.3 0.10 0.070.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.A242.2 0.35 0.6 3.74.5 0.10 1.31.7 0.150.25 1.82.3 0.10 0.070.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.295.1 0.71.5 0.8 4.05.0 0.35 0.03 . . . . . . 0.35 0.25 . . . . . . .

25、 . . . . . . . . . . . . . . 0.05 0.15 Rem.295.2 0.71.2 0.8 4.05.0 0.30 0.03 . . . . . . 0.30 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.296.1 2.03.0 0.9 4.05.0 0.35 0.05 . . . 0.35 0.50 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.35 Rem.296.2 2.03.0 0.8 4.05.0 0.30 0.03

26、 . . . . . . 0.30 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.301.1L,M 9.510.5 0.81.2 3.03.5 0.500.8 0.300.50 . . . 1.01.5 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.302.1L,M 9.510.5 0.20 2.83.2 . . . 0.81.2 . . . 1.01.5 0.05 0.20 . . . . . . . . . . . . . . .

27、 . . . . . . 0.03 0.10 Rem.303.1L,M 9.510.5 0.81.2 0.20 0.500.8 0.500.7 . . . . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.304.1M 9.511.5 0.81.0 0.050.08 0.300.50 0.350.50 0.05 0.03 0.20 0.030.18 . . . . . . . . . 0.03 . . . . . . . . . 0.03 0.15 Rem.308.1M 5.06.0 0.8 4.05

28、.0 0.50 0.10 . . . . . . 1.0 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.308.2M 5.06.0 0.8 4.05.0 0.30 0.10 . . . . . . 0.50 0.20 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.318.1M 5.56.5 0.8 3.04.0 0.50 0.150.6 . . . 0.35 0.9 0.25 . . . . . . . . . . . . . . . . . . .

29、 . . . . . 0.50 Rem.319.1M 5.56.5 0.8 3.04.0 0.50 0.10 . . . 0.35 1.0 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.319.2M 5.56.5 0.6 3.04.0 0.10 0.10 . . . 0.10 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . . . . 0.20 Rem.A319.1M 5.56.5 0.8 3.04.0 0.50 0.10 . . . 0.35 3.0 0.25

30、 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.B319.1M 5.56.5 0.9 3.04.0 0.8 0.150.50 . . . 0.50 1.0 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.320.1M 5.08.0 0.9 2.04.0 0.8 0.100.6 . . . 0.35 3.0 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.328.1M 7.58.

31、5 0.8 1.02.0 0.200.6 0.250.6 0.35 0.25 1.5 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.332.1M 8.510.5 0.9 2.04.0 0.50 0.61.5 . . . 0.50 1.0 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.332.2M 8.510.0 0.6 2.04.0 0.10 0.91.3 . . . 0.10 0.10 0.20 . . . . . . . . . . .

32、 . . . . . . . . . . . . . 0.30 Rem.333.1M 8.510.0 0.8 3.04.0 0.50 0.100.50 . . . 0.50 1.0 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.A333.1M 8.510.0 0.8 3.04.0 0.50 0.100.50 . . . 0.50 3.0 0.25 . . . . . . . . . . . . . . . . . . . . . . . . 0.50 Rem.336.1M 11.013.0 0.9 0.501.5 0

33、.35 0.81.3 . . . 2.03.0 0.35 0.25 . . . . . . . . . . . . . . . . . . . . . 0.05 . . . Rem.336.2M 11.013.0 0.9 0.501.5 0.10 0.91.3 . . . 2.03.0 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.339.1M 11.013.0 0.9 1.53.0 0.50 0.61.5 . . . 0.501.5 1.0 0.25 . . . . . . . . . . . . . .

34、. . . . . . . . . . 0.50 Rem.354.1M 8.69.4 0.15 1.62.0 0.10 0.450.6 . . . . . . 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.354.2M 8.69.4 0.06 1.62.0 0.10 0.450.6 . . . . . . 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.355.1M 4.55.5 0.50I 1.01.5 0.50I 0.45

35、0.6 0.25 . . . 0.35 0.25 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.B179182TABLE 1 Continued355.2M 4.55.5 0.140.25 1.01.5 0.05 0.500.6 . . . . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.DESIG.S Si Fe Cu Mn Mg Cr Ni Zn Ti Ag Be Pb Sn Zr FNs OTHERSA,E Al Min.AA

36、No. Each TotalFA355.2M 4.55.5 0.06 1.01.5 0.03 0.500.6 . . . . . . 0.03 0.040.20 . . . . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.C355.1M 4.55.5 0.15 1.01.5 0.10 0.450.6 . . . . . . 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.C355.2M 4.55.5 0.13 1.01.5 0.05 0.500.6 . . .

37、 . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.356.1M 6.57.5 0.50I 0.25 0.35I 0.250.45 . . . . . . 0.35 0.25 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.356.2M 6.57.5 0.130.25 0.10 0.05 0.300.45 . . . . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.0

38、5 0.15 Rem.A356.1M 6.57.5 0.15 0.20 0.10 0.300.45 . . . . . . 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.A356.2M 6.57.5 0.12 0.10 0.05 0.300.45 . . . . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.B356.2M 6.57.5 0.06 0.03 0.03 0.300.45 . . . . . . 0.03

39、 0.040.20 . . . . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.C356.2M 6.57.5 0.04 0.03 0.03 0.300.45 . . . . . . 0.03 0.040.20 . . . . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.F356.2M 6.57.5 0.12 0.10 0.05 0.170.25 . . . . . . 0.05 0.040.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0

40、.15 Rem.357.1M 6.57.5 0.12 0.05 0.03 0.450.6 . . . . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.A357.2M 6.57.5 0.12 0.10 0.05 0.450.7 . . . . . . 0.05 0.040.20 . . . 0.040.07 . . . . . . . . . . . . . . . 0.03 0.10 Rem.B357.2M 6.57.5 0.06 0.03 0.03 0.450.6 . . . . . . 0.03

41、 0.040.20 . . . . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.C357.2M 6.57.5 0.06 0.03 0.03 0.500.7 . . . . . . 0.03 0.040.20 . . . 0.400.07 . . . . . . . . . . . . . . . 0.03 0.10 Rem.E357.1M 6.57.5 0.07 . . . 0.10 0.60.7 . . . . . . . . . 0.100.20 . . . 0.002 . . . . . . . . . . . . . . . 0.05

42、 0.15 Rem.E357.2M 6.57.5 0.07 . . . 0.10 0.60.7 . . . . . . . . . 0.100.20 . . . 0.0003 . . . . . . . . . . . . . . . 0.05 0.15 Rem.F357.1M 6.57.5 0.07 0.20 0.10 0.450.7 . . . . . . 0.10 0.040.20 . . . 0.002 . . . . . . . . . . . . . . . 0.05 0.15 Rem.F357.2M 6.57.5 0.07 0.20 0.10 0.450.7 . . . . .

43、. 0.10 0.040.20 . . . 0.0003 . . . . . . . . . . . . . . . 0.05 0.15 Rem.358.2M 7.68.6 0.20 0.10 0.10 0.450.6 0.05 . . . 0.10 0.120.20 . . . 0.150.30 . . . . . . . . . . . . . . . 0.05 0.15 Rem.359.2M 8.59.5 0.12 0.10 0.10 0.550.7 . . . . . . 0.10 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05

44、0.15 Rem.A359.1L,M 8.59.5 0.20 0.20 0.10 0.450.6 . . . . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.03 0.10 Rem.360.2M 9.010.0 0.71.1 0.10 0.10 0.450.6 . . . 0.10 0.10 . . . . . . . . . . . . 0.10 . . . . . . . . . . . . 0.20 Rem.A360.1J,M 9.010.0 1.0 0.6 0.35 0.450.6 . . . 0.50 0.40

45、. . . . . . . . . . . . 0.15 . . . . . . . . . . . . 0.25 Rem.A360.2M 9.010.0 0.6 0.10 0.05 0.450.6 . . . . . . 0.05 . . . . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.361.1M 9.510.5 0.8 0.50 0.25 0.450.6 0.200.30 0.200.30 0.40 0.20 . . . . . . . . . 0.10 . . . . . . . . . 0.05 0.15 Rem.3

46、62.1N 10.511.5 0.30 0.20 0.250.35 0.60.7 . . . 0.10 0.10 0.20 . . . . . . . . . 0.10 . . . . . . Q 0.05 0.15 Rem.363.1M 4.56.0 0.8 2.53.5 . . . 0.200.40 . . . 0.25 3.04.5 0.20 . . . . . . 0.25 0.25 . . . 0.8 Mn+Cr . . . . . . 0.30 Rem.364.2M 7.59.5 0.71.1 0.20 0.10 0.250.40 0.250.50 .015 0.15 . . .

47、. . . 0.020.04 . . . 0.15 . . . . . . . . . 0.05 0.15 Rem.365.1N 9.511.5 0.12 0.03 0.500.8 0.150.50 . . . . . . 0.07 0.040.15 . . . . . . . . . . . . . . . . . . K 0.03 0.10 Rem.A365.1N 9.511.5 0.150.20 0.02 0.300.6 0.150.6 . . . . . . 0.03 0.10 . . . . . . . . . . . . . . . . . . R 0.05 0.15 Rem.36

48、6.1M,O 6.57.5 0.12 0.05 0.03 0.61.2 . . . . . . 0.05 0.20 . . . . . . . . . . . . . . . . . . . . . 0.05 0.15 Rem.367.1N 8.59.5 0.20 0.25 0.250.35 0.350.50 . . . . . . 0.10 0.20 . . . . . . . . . . . . . . . . . . Q 0.05 0.15 Rem.368.1N 8.59.5 0.20 0.25 0.250.35 0.150.30 . . . . . . 0.10 0.20 . . .

49、. . . . . . . . . . . . . . . Q 0.05 0.15 Rem.369.1M 11.012.0 1.0 0.50 0.35 0.300.45 0.300.40 0.05 0.9 . . . . . . . . . . . . 0.10 . . . . . . . . . 0.05 0.15 Rem.380.2M 7.59.5 0.71.1 3.04.0 0.10 0.10 . . . 0.10 0.10 . . . . . . . . . . . . 0.10 . . . . . . . . . . . . 0.20 Rem.A380.1J,M 7.59.5 1.0 3.04.0 0.50 0.10 . . . 0.50 2.9