ASTM B241 B241M-2010 Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube《铝及铝合金无缝管和挤压制无缝管的标准规格》.pdf

1、Designation: B241/B241M 10Used in USNRC-RDT standardsStandard Specification forAluminum and Aluminum-Alloy Seamless Pipe andSeamless Extruded Tube1This standard is issued under the fixed designation B241/B241M; the number immediately following the designation indicates the yearof original adoption o

2、r, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*

3、1.1 This specification2covers aluminum and aluminumal-loy seamless pipe in the alloys (Note 1) and tempers shown inTable 1 Table 2 and seamless extruded round tube in thealloys and tempers shown in Table 3 Table 4 intended forpressure applications. The standard sizes for seamless pipe arelisted in T

4、able 16.7 of ANSI H35.2 and H35.2M. Nonstandardalloys, tempers, and sizes of pipe are produced as seamlessextruded tube.NOTE 1Throughout this specification, use of the term alloy, in thegeneral sense, includes aluminum as well as aluminum alloy.NOTE 2For other seamless drawn tubes, see Specification

5、 B210 orSpecification B483/B483M. For extruded tube see Specification B221,and for structural pipe and tube see Specification B429/B429M.1.2 Alloy and temper designations are in accordance withANSI H35.1/H35.1M. The equivalent Unified NumberingSystem alloy designations are those of Table 5preceded b

6、y A9,for example, A91100 for aluminum 1100 in accordance withPractice E527.1.3 For acceptance criteria for inclusion of new aluminumand aluminum alloys in this specification, see Annex A2.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The value

7、s stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.4.1 The SI units are shown either in brackets or in separatetables.2. Referenced Documents2.1 The

8、 following documents of the issue in effect on dateof material purchase form a part of this specification to theextent referenced herein:2.2 ASTM Standards:3B210 Specification for Aluminum and Aluminum-AlloyDrawn Seamless TubesB221 Specification for Aluminum and Aluminum-AlloyExtruded Bars, Rods, Wi

9、re, Profiles, and TubesB429/B429M Specification for Aluminum-Alloy ExtrudedStructural Pipe and TubeB483/B483M Specification for Aluminum and Aluminum-Alloy Drawn Tube and Pipe for General Purpose Applica-tionsB557 Test Methods for Tension Testing Wrought and CastAluminum- and Magnesium-Alloy Product

10、sB557M Test Methods forTensionTestingWrought and CastAluminum- and Magnesium-Alloy Products (Metric)B594 Practice for Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace ApplicationsB647 Test Method for Indentation Hardness of AluminumAlloys by Means of a Webster Hardness GageB648

11、 Test Method for Indentation Hardness of AluminumAlloys by Means of a Barcol ImpressorB660 Practices for Packaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Alumi-num and Magnesium ProductsB807/B807M Practice for Extrusion Press Solution HeatTreatment

12、 for Aluminum AlloysB918 Practice for Heat Treatment of Wrought AluminumAlloysB945 Practice forAluminumAlloy Extrusions Press Cooledfrom an Elevated Temperature Shaping Process for Pro-duction of T1, T2, T5 and T10Type TempersE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice

13、for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base Alloys1This specification is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommitte

14、e B07.03 onAluminum Alloy Wrought Products.Current edition approved Dec. 1, 2010. Published January 2011. Originallyapproved in 1949. Last previous edition approved in 2002 as B241/B241M02.DOI: 10.1520/B0241_B0241M-10.2For ASME Boiler and Pressure Vessel Code applications see related Specifi-cation

15、SB-241/SB-241M in Section II of that Code.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Chan

16、ges section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.E227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by theTABLE 1 Tensile Property Limits for Pip

17、e, Inch-Pound UnitsA,BAlloy TemperPipe Size,in.Tensile Strength,min, ksiYield Strength(0.2 % Offset),min, ksiElongation in2 in. or 4 3Diameter, min, %C3003 H18 Under 1 27.0 24.0 4H112 1 and over 14.0 5.0 256005 T1 All 25.0 15.0 16T5 All 38.0 35.0 86005A T1 All 25.0 14.5 15T5 All 38.0 31.0 7T61 Under

18、 0.250 38.0 35.0 80.250-1.000 38.0 35.0 106041DT6 All 45.0 40.0 106042 T5, T5511 All 38.0 35.0 106061 T6 (Extruded) Under 1 38.0 35.0 81 and over 38.0 35.0 10ET6 (Drawn) Under 1 42.0 35.0 8F1 and over 38.0 35.0 10G6063 T6 All 30.0 25.0 86064DT6 All 38.0 35.0 106082 T6 All 45.0 38.0 86105 T1 All 25.0

19、 15.0 16T5 All 38.0 35.0 86262 T6 All 38.0 35.0 106351 T5 All 38.0 35.0 10ET6 All 42.0 37.0 10HAThe basis for establishment of tensile property limits is shown in Annex A1.BFor purposes of determining conformance with this specification, each value for tensile strength and yield strength shall be ro

20、unded to the nearest 0.1 ksi, and eachvalue for elongation shall be rounded to the nearest 0.5 %, both in accordance with the rounding-off method of Practice E29.CElongation of full-section and cut-out sheet-type specimens is measured in 2 in.; of round specimens, in 4 3 specimen diameter.DTentative

21、Properties subject to revision.EFor wall thicknesses less than 0.250 in., the minimum elongation is 8 %.FFor wall thickness 0.050 to 0.259 in., the minimum elongation is 10 %.GFor wall thickness 0.260 to 0.500 in., the minimum elongation is 12 %.HFor wall thickness less than 0.125 in., the minimum e

22、longation is 8 %.TABLE 2 Tensile Property Limits for Pipe SI UnitsA,BAlloyTemper(Product)Pipe Size, DesignationTensile Strength,min, MPaYield Strength(0.2 % Offset),min, MPaElongation,Cmin, %in 50 mmin 5 3 Diameter(5.65 =A )3003 H18 Under 1 185 165 4 .H112 1 and over 95 35 25 226005 T1 All 170 105 1

23、6 14T5 All 260 240 86005A T1 All 170 100 15T5 All 260 215 7 6T61 All 260 240 86041DT6 All 310 275 10 96042 T5, T5511 All 260 240 10 96061 T6 (Extruded) Under 1 260 240 8 .1 and over 260 240 10E9T6 (Drawn) Under 1 290 240 8F.1 and over 260 240 10G96063 T6 All 205 170 8 76064DT6 All 260 240 10 96082 T

24、6 All 310 260 10 86105 T5 All 260 240 8 7T6 All 290 255 10 96262 T6 All 260 240 10 96351 T5 All 260 240 10E9T6 All 290 255 10H9AThe basis for establishment of mechanical property limits is shown in Annex A1.BFor purposes of determining conformance with this specification, each value for ultimate str

25、ength and yield strength shall be rounded to the nearest 1 MPa, and eachvalue for elongation shall be rounded to the nearest 0.5 %, both in accordance with the rounding-off method of Practice E29.CElongations in 50 mm apply for pipe tested in full-section and to sheet type specimens taken from pipes

26、 having a wall up to 12.50 mm thick. Elongations in 5D (5.65= A ), where D and A are diameter and cross-sectional area of the specimens respectively, apply to round test specimens machined from wall thicknesses over 6.30 mm.DTentative, are subject to modification.EFor wall thicknesses up through 6.3

27、0 mm the minimum elongation is 8 %.FFor wall thicknesses over 1.25 through 6.60 mm, the minimum elongation is 10 %.GFor wall thicknesses over 6.60 through 12.50 mm, the minimum elongation is 12 %.HFor wall thicknesses up through 3.20 mm the minimum elongation is 8 %.B241/B241M 102TABLE 3 Tensile Pro

28、perty Limits for Extruded Tube, Inch-Pound UnitsA,BTemperSpecified Section orWall Thickness, in.Area, in.2Tensile Strength, ksiYield Strength(0.2 % Offset), ksiElongation in 2in.or43Diameter, min,%CMin Max Min MaxAluminum 1060O all all 8.5 14.0 2.5 . . . 25H112 all all 8.5 . . . 2.5 . . . 25FDall al

29、l . . . . .Aluminum 1100O all all 11.0 15.5 3.0 . . . 25H112 all all 11.0 . . . 3.0 . . . 25FDall all . . . . .Alloy 2014O all all . . . 30.0 . . . 18.0 12T4JT4510Eall all 50.0 . . . 35.0 . . . 12T4511ET42 all all 50.0 . . . 29.0 . . . 12T6JHup thru 0.499 all 60.0 . . . 53.0 . . . 7T6510E0.5000.749

30、all 64.0 . . . 58.0 . . . 7T6511E0.750 and over up thru 25 68.0 . . . 60.0 . . . 7over 25 thru 32 68.0 . . . 58.0 . . . 6T62 up thru 0.749 all 60.0 . . . 53.0 . . . 70.750 and over up thru 25 60.0 . . . 53.0 . . . 7over 25 thru 32 60.0 . . . 53.0 . . . 6FDall all . . . . .Alloy 2024O all all . . . 3

31、5.0 . . . 19.0 12T3J5up thru 0.249 all 57.0 . . . 42.0 . . . 10T3510E0.2500.749 all 60.0 . . . 44.0 . . . 10T3511E0.7501.499 all 65.0 . . . 46.0 . . . 101.500 and over up thru 25 70.0 . . . 48.0 . . . 10over 25 thru 32 68.0 . . . 46.0 . . . 8T42 up thru 0.749 all 57.0 . . . 38.0 . . . 120.7501.499 a

32、ll 57.0 . . . 38.0 . . . 101.500 and over up thru 25 57.0 . . . 38.0 . . . 10over 25 thru 32 57.0 . . . 38.0 . . . 8T81H0.0500.249 all 64.0 . . . 56.0 . . . 4T8510E0.2501.499 all 66.0 . . . 58.0 . . . 5T8511E1.500 and over up thru 32 66.0 . . . 58.0 . . . 5FDall all . . . . .Alloy 2219O all all . .

33、. 32.0 . . . 18.0 12T31JT3510EHup thru 0.499 up thru 25 42.0 . . . 26.0 . . . 14T3511E0.5002.999 up thru 25 45.0 . . . 27.0 . . . 14T62 Up thru 0.999 up thru 25 54.0 . . . 36.0 . . . 61.000 and over up thru 25 54.0 . . . 36.0 . . . 6T81JT8510Eup thru 2.999 up thru 25 58.0 . . . 42.0 . . . 6T8511EFDa

34、ll all . . . . .Alloy 3003O all all 14.0 19.0 5.0 . . . 25H112 all all 14.0 . . . 5.0 . . . 25FDall all . . . . .Alclad Alloy 3003B241/B241M 103TABLE 3 ContinuedTemperSpecified Section orWall Thickness, in.Area, in.2Tensile Strength, ksiYield Strength(0.2 % Offset), ksiElongation in 2in.or43Diameter

35、, min,%CMin Max Min MaxO all all 13.0 18.0 4.5 . . . 25H112 all all 13.0 . . . 4.5 . . . 25FDall all . . . . .Alloy 5052O all all 25.0 35.0 10.0 . . . . . .FDall all . . . . .Alloy 5083O all up thru 32 39.0 51.0 16.0 . . . 14H111 all up thru 32 40.0 . . . 24.0 . . . 12H112 all up thru 32 39.0 . . .

36、16.0 . . . 12FDall all . . . . .Alloy 5086O all up thru 32 35.0 46.0 14.0 . . . 14H111 all up thru 32 36.0 . . . 21.0 . . . 12H112 all up thru 32 35.0 . . . 14.0 . . . 12FDall all . . . . .Alloy 51540 all all 30.0 41.0 11.0 . . .H112 all all 30.0 . . . 11.0 . . .Alloy 5454O all up thru 32 31.0 41.0

37、12.0 . . . 14H111 all up thru 32 33.0 . . . 19.0 . . . 12H112 all up thru 32 31.0 . . . 12.0 . . . 12FDall all . . . . .Alloy 5456O all up thru 32 41.0 53.0 19.0 . . . 14H111 all up thru 32 42.0 . . . 26.0 . . . 12H112 all up thru 32 41.0 . . . 19.0 . . . 12FDall all . . . . .Alloy 6005T1 Up thru 0.

38、500 all 25.0 15.0 16T5 Up thru 0.124 all 38.0 35.0 80.1251.000 all 38.0 35.0 10Alloy 6005AT1 Up thru 0.249 all 25.0 14.5 15T5 Up thru 0.249 all 38.0 31.0 70.2500.999 all 38.0 31.0 9T61 Up thru 0.249 all 38.0 35.0 80.2501.000 all 38.0 35.0 10Alloy 6041T6,T6511F0.4002.000 all 45.0 40.0 10Alloy 6042T5,

39、T55110.4000.499 all 38.0 35.0 100.5001.800 all 42.0 35.0 10Alloy 6061O all all . . . 22.0 . . . 16.0 16T1 up thru 0.625 all 26.0 . . . 14.0 . . . 16T4JT4510Eall all 26.0 . . . 16.0 . . . 16T4511ET42 all all 26.0 . . . 12.0 . . . 16T51 up thru 0.625 all 35.0 . . . 30.0 . . . 8B241/B241M 104TABLE 3 Co

40、ntinuedTemperSpecified Section orWall Thickness, in.Area, in.2Tensile Strength, ksiYield Strength(0.2 % Offset), ksiElongation in 2in.or43Diameter, min,%CMin Max Min MaxT6, T62JT6510Eup thru 0.249 all 38.0 . . . 35.0 . . . 8T6511E0.250 and over all 38.0 . . . 35.0 . . . 10FDall all . . . . .Alloy 60

41、63O all all . 19.0 . . 18T1Gup thru 0.500 all 17.0 . . . 9.0 . . . 120.5011.000 all 16.0 . . . 8.0 . . . 12T4, T42 up through 0.500 all 19.0 . . . 10.0 . . . 140.5011.000 all 18.0 . . . 9.0 . . . 14T5 up thru 0.500 all 22.0 . . . 16.0 . . . 80.5011.000 all 21.0 . . . 15.0 . . . 8T52 up thru 1.000 al

42、l 22.0 30.0 16.0 25.0 8T6, T62 up thru 0.124 all 30.0 . . . 25.0 . . . 80.1251.000 all 30.0 . . . 25.0 . . . 10FDall all . . . . .Alloy 6064,T6T6511F0.4002.000 all 38.0 35.0 10Alloy 6066O all all . . . 29.0 . . . 18.0 16T4,T4510Eall all 40.0 . . . 25.0 . . . 14T4511ET42 all all 40.0 . . . 24.0 . . .

43、 14T6,T6510,Eall all 50.0 . . . 45.0 . . . 8T6511ET62 all all 50.0 . . . 42.0 . . . 8Alloy 6082T6 0.2001.000 all 45.0 38.0 8Alloy 6105T1 Up thru 0.500 all 25.0 15.0 16T5 Up thru 0.500 all 38.0 35.0 8Alloy 6162T5,T5510Eup thru 1.000 all 37.0 . . . 34.0 . . . 7T5511ET6,T6510Eup thru 0.249 all 38.0 . .

44、 . 35.0 . . . 8T6511E0.2500.499 all 38.0 . . . 35.0 . . . 10Alloy 6262T6,T6511all all 38.0 35.0 10Alloy 6351T4 up thru 0.749 all 32.0 . . . 19.0 . . . 16T6 up thru 0.124 . . . 42.0 . . . 37.0 . . . 80.1250749 . . . 42.0 . . . 37.0 . . . 10Alloy 7075O all . . 40.0 . 24.0 10B241/B241M 105Point-to-Plan

45、e Technique4E527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)E607 Test Method for Atomic Emission SpectrometricAnalysis Aluminum Alloys by the Point to Plane Tech-nique Nitrogen AtmosphereE716 Practices for Sampling and Sample Preparation ofAluminum and Aluminum Allo

46、ys for Determination ofChemical Composition by Spectrochemical AnalysisE1004 Test Method for Determining Electrical Conductiv-ity Using the Electromagnetic (Eddy-Current) MethodE1251 Test Method for Analysis of Aluminum and Alumi-num Alloys by Atomic Emission SpectrometryG47 Test Method for Determin

47、ing Susceptibility to Stress-Corrosion Cracking of 2XXX and 7XXXAluminumAlloyProducts2.3 ANSI Standards:H35.1/H35.1(M) Alloy and Temper Designation Systemsfor Aluminum5H35.2 Dimensional Tolerances for Aluminum Mill Prod-ucts5H35.2(M) Dimensional Tolerances for Aluminum MillProducts Metric52.4 Federa

48、l Standard:Fed. Std. No. 123 Marking for Shipment (Civil Agencies)62.5 Military Standard:MIL-STD-129 Marking for Shipment and Storage62.6 AMS Specification:4Withdrawn. The last approved version of this historical standard is referencedon www.astm.org.5Available from Aluminum Association, Inc., 1525

49、Wilson Blvd., Suite 600,Arlington, VA 22209, http:/www.aluminum.org.6Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.TABLE 3 ContinuedTemperSpecified Section orWall Thickness, in.Area, in.2Tensile Strength, ksiYield Strength(0.2 % Offset), ksiElongation in 2in.or43Diameter, min,%CMin Max Min MaxT6, T62J5up through 0.249 all 78.0 . . . 70.0 . . . 7T6510E0.2500.499 all 81.0 . . . 73.0 . . . 7T6511E0.5001.499 all 81.0 . . . 72.0 . . . 71.50