1、Designation: B 248 07Standard Specification forGeneral Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar1This standard is issued under the fixed designation B 248; the number immediately following the designation indicates the year oforiginal adoption or, in the ca
2、se of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This sp
3、ecification establishes the general requirementscommon to several wrought product specifications. Unlessotherwise specified in the purchase order or in an individualspecification, these general requirements shall apply to copperand copper-alloy plate, sheet, strip, and rolled bar suppliedunder each
4、of the following product specifications issued byASTM: B 36/B 36M, B 96/B 96M, B 103/B 103M, B 121/B 121M, B 122/B 122M, B 152/B 152M, B 169/B 169M,B 194, B 422, B 465, B 534, B 591, B 592, B 694, B 740,B 747, and B 768.2NOTE 1A complete metric companion to Specification B 248 hasbeen developedB 248
5、M; therefore no metric equivalents are presentedin this specification.1.2 UnitsThis specification is the companion specificationto SI Specification B 248M; therefore, no SI equivalents areshown in this specification.2. Referenced Documents2.1 The following documents of the issue in effect on dateof
6、material purchase form a part of this specification to theextent referenced herein:2.2 ASTM Standards:3B 36/B 36M Specification for Brass Plate, Sheet, Strip, AndRolled BarB 96/B 96M Specification for Copper-Silicon Alloy Plate,Sheet, Strip, and Rolled Bar for General Purposes andPressure VesselsB 1
7、03/B 103M Specification for Phosphor Bronze Plate,Sheet, Strip, and Rolled BarB 121/B 121M Specification for Leaded Brass Plate, Sheet,Strip, and Rolled BarB 122/B 122M Specification for Copper-Nickel-Tin Alloy,Copper-Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, an
8、d Rolled BarB 152/B 152M Specification for Copper Sheet, Strip, Plate,and Rolled BarB 169/B 169M Specification for Aluminum Bronze Sheet,Strip, and Rolled BarB 193 Test Method for Resistivity of Electrical ConductorMaterialsB 194 Specification for Copper-Beryllium Alloy Plate,Sheet, Strip, and Rolle
9、d BarB 248M Specification for General Requirements forWrought Copper and Copper-Alloy Plate, Sheet, Strip, andRolled Bar MetricB 422 Specification for Copper-Aluminum-Silicon-CobaltAlloy, Copper-Nickel-Silicon-Magnesium Alloy, Copper-Nickel-Silicon Alloy, Copper-Nickel-Aluminum-MagnesiumAlloy, and C
10、opper-Nickel-TinAlloy Sheet andStripB 465 Specification for Copper-Iron Alloy Plate, Sheet,Strip, and Rolled BarB 534 Specification for Copper-Cobalt-BerylliumAlloy andCopper-Nickel-Beryllium Alloy Plate, Sheet, Strip, andRolled BarB 543 Specification for Welded Copper and Copper-AlloyHeat Exchanger
11、 TubeB 591 Specification for Copper-Zinc-Tin and Copper-Zinc-Tin-Iron-Nickel Alloys Plate, Sheet, Strip, and Rolled BarB 592 Specification for Copper-Zinc-Aluminum-Cobalt Al-loy, Copper-Zinc-Tin-Iron Alloy Plate, Sheet, Strip, andRolled BarB 694 Specification for Copper, Copper-Alloy, Copper-Clad Br
12、onze (CCB), Copper-Clad Stainless Steel (CCS),and Copper-Clad Alloy Steel (CAS) Sheet and Strip forElectrical Cable ShieldingB 740 Specification for Copper-Nickel-Tin Spinodal AlloyStrip1This specification is under the jurisdiction of the ASTM Committee B05 onCopper and Copper Alloys and is the dire
13、ct responsibility of Subcommittee B05.01on Plate, Sheet, and Strip.Current edition approved Oct. 1, 2007. Published October 2007. Originallyapproved in 1951. Last previous edition approved in 2006 as B 248 06.2The UNS system for copper and copper alloys (see Practice E 527) is a simpleexpansion of t
14、he former standard designation system accomplished by the additionof a prefix “C” and a suffix “00”. The suffix can be used to accommodatecomposition variations of the base alloy.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.
15、 For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.B
16、 747 Specification for Copper-Zirconium Alloy Sheet andStripB 768 Specification for Copper-Cobalt-BerylliumAlloy andCopper-Nickel-Beryllium Alloy Strip and SheetB 846 Terminology for Copper and Copper AlloysE8 Test Methods for Tension Testing of Metallic MaterialsE18 Test Methods for Rockwell Hardne
17、ss of MetallicMaterialsE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE50 Practices for Apparatus, Reagents, and Safety Consid-erations for Chemical Analysis of Metals, Ores, andRelated MaterialsE53 Test Method for Determination of Copper in Unal-lo
18、yed Copper by GravimetryE54 Test Methods for Chemical Analysis of SpecialBrasses and Bronzes4E62 Test Methods for Chemical Analysis of Copper andCopper Alloys (Photometric Methods)E75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc AlloysE 106 Test Methods for Chemical Anal
19、ysis of Copper-Beryllium AlloysE112 Test Methods for Determining Average Grain SizeE118 Test Methods for Chemical Analysis of Copper-Chromium AlloysE 121 Test Methods for Chemical Analysis of Copper-Tellurium AlloysE 255 Practice for Sampling Copper and Copper Alloys forthe Determination of Chemical
20、 CompositionE 478 Test Methods for Chemical Analysis of CopperAlloysE 527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)3. Terminology3.1 For definitions of terms related to copper and copperalloys, see Terminology B 846.3.2 Definitions of Terms Specific to This Standa
21、rd:3.2.1 coil, na length of the product wound into a series ofconnected turns. The unqualified term “coil” as applied to “flatproduct” usually refers to a coil in which the product is spirallywound, with the successive layers on top of one another.(Sometimes called a “roll.”)3.2.2 lengths, mill, nst
22、raight lengths, including ends, thatcan be conveniently manufactured in the mills. Full-lengthpieces are usually 8, 10, or 12 ft and subject to establishedlength tolerances.3.2.3 lengths, stock, nstraight lengths that are mill cut andstored in advance of orders. They are usually 8, 10, or 12 ft ands
23、ubject to established length tolerances.3.2.4 rolled bar, na rolled flat product over 0.188 in. thickand up to and including 12 in. wide, with sheared, sawed, ormachined edges, in straight lengths or coils (rolls).4. Materials and Manufacture4.1 Materials:4.1.1 The material of manufacture shall be a
24、 cast bar, cake,or slab of such purity and soundness as to be suitable forprocessing into the products to the product specification listedin Section 1.4.1.2 In the event heat identification or traceability isrequired, the purchaser shall specify the details desired.4.2 Manufacture:4.2.1 The product
25、shall be manufactured by such hot-working or cold-working and annealing processes as to pro-duce a uniform wrought structure in the finished product.4.2.2 The product shall be hot or cold-worked to the finishedsize and subsequently annealed when required, to meet thetemper properties specified.4.3 E
26、dgesThe edges shall be slit, sheared, sawed, orrolled edges, as specified. Slit edges shall be furnished unlessotherwise specified in the contract or purchase order. See 5.6for edge descriptions and corresponding tables for tolerances.5. Dimensions, Weights, and Permissible Variations5.1 GeneralFor
27、the purpose of determining conformancewith the dimensional requirements prescribed in this specifi-cation, any measured value outside the specified limitingvalues for any dimension may be cause for rejection.NOTE 2Blank spaces in the tolerance tables indicate either that thematerial is not available
28、 or that no tolerances have been established.5.2 ThicknessThe standard method of specifying thick-ness shall be in decimal fractions of an inch. For material 0.021in. and under in thickness, it is recommended that the nominalthicknesses be stated not closer than the nearest half-thousandth. (For exa
29、mple, specify 0.006 or 0.0065 in., but not0.0063 in.) For material over 0.021 in. in thickness, it isrecommended that the nominal thicknesses be stated not closerthan the nearest thousandth. (For example, specify 0.128 or0.129 in., but not 0.1285 in.) A list of preferred thicknesses isshown inAppend
30、ix X1. The thickness tolerances shall be thoseshown in Tables 1-3 for the product specification indicated:5.2.1 Table 1Thickness tolerances applicable to Specifi-cations B 36/B 36M, B 103/B 103M, B 121/B 121M, B 152/B 152M, B 465, B 591, B 592, and B 747.5.2.2 Table 2Thickness tolerances applicable
31、to Specifi-cations B 96/B 96M, B 122/B 122M, B 169/B 169M, B 194,B 422, B 534, B 740, and B 768.5.2.3 Table 3Special thickness tolerances applicable toCopper Alloy UNS No. C72500 when ordered to SpecificationB 122/B 122M, and to Specifications B 194, B 534, B 740, andB 768 as noted in the table.5.3
32、WidthThe width tolerances shall be those shown inTables 4-6, depending on the type of edge required (see 5.3.1,5.3.2, and 5.3.3):5.3.1 Table 4Width tolerances for slit metal and slit metalwith rolled edges.5.3.2 Table 5Width tolerances for square-sheared metal.5.3.3 Table 6Width tolerances for sawed
33、 metal.5.4 LengthThe material shall be furnished in coils orstraight lengths of plate, sheet, strip, or rolled bar as specified.The length tolerances for straight lengths shall be those shown4Withdrawn.B248072in Tables 7-10, depending on the method of cutting required(see 5.4.1-5.4.4). When ends are
34、 permitted, the length andquantity of the ends shall be in accordance with the schedule inTable 8.5.4.1 Table 7Length tolerances, for straight lengths.5.4.2 Table 8Schedule of minimum length and maximumweight of ends for lengths with ends.5.4.3 Table 9Length tolerances for square-sheared metal.5.4.4
35、 Table 10Length tolerances for sawed metal.5.5 StraightnessThe straightness tolerances, which arethe maximum edgewise curvature (depth of arc) in any 72-in.portion of the total length, shall be those shown in Tables11-13, depending on the type of edge required.5.5.1 Table 11Straightness tolerances f
36、or metal as slit, oras slit and straightened, or as slit and edge-rolled, or metal withdrawn edges.5.5.2 Table 12Straightness tolerances for square-shearedmetal.5.5.3 Table 13Straightness tolerances for sawed metal.5.6 EdgesWhen rolled edges are required, they may beproduced by either rolling or dra
37、wing to one of the followingspecified edge contours:5.6.1 Square Edges (Square Corners)Edges shall havecommercially-squared corners and with a maximum cornerradius as prescribed in Table 14.5.6.2 Rounded CornersEdges shall have rounded cornersas shown in Fig. 1 with a radius as prescribed in Table 1
38、5.5.6.3 Rounded EdgesEdges shall be rounded as shown inFig. 2 with a radius as prescribed in Table 16.5.6.4 Full-Rounded EdgesEdges shall be full rounded asshown in Fig. 3 with a radius as prescribed in Table 17.5.7 Weight Tolerances for Hot-Rolled Material:5.7.1 Table 18Lot weight tolerances for ho
39、t-rolled sheetand plate applicable to Specifications B 36/B 36M, B 96/B 96M (Copper Alloy UNS No. C65500), B 103/B 103M,B 122/B 122M, B 152/B 152M, and B 591.5.7.2 The weight of each lot of five or more plates or sheetsof the same type and the same specified dimensions whenordered to thickness, shal
40、l not vary from the theoretical bymore than the amount prescribed in Table 18 for the productspecification indicated. The weight of any individual plate orsheet may vary from the nominal by not more than one third inexcess of the tolerances prescribed in Table 18 for the productspecification indicat
41、ed. The tolerances for lots of less than fiveplates or sheets shall be governed by the tolerances forindividual plates or sheets.5.7.3 For the purpose of calculation, the densities of thematerials covered by these specifications are listed inAppendixX2.6. Workmanship, Finish and Appearance6.1 The ma
42、terial shall be free of defects, but blemishes of anature that do not interfere with the intended application areacceptable. A superficial film of residual light lubricant isnormally present and is acceptable unless otherwise specified.7. Sampling7.1 SamplingThe lot size, portion size, and selection
43、 ofsample pieces shall be as follows:7.1.1 Lot SizeAn inspection lot shall be 10 000 lb or lessmaterial of the same mill form, alloy, temper, and nominaldimensions, subject to inspection at one time or shall be theproduct of one cast bar from a single melt charge, whoseTABLE 1 Thickness Tolerances(A
44、pplicable to Specifications B 36/B 36M, B 103/B 103M, B 121/B 121M, B 152/B 152M, B 465, B 591, B 592, and B 747)Thickness, in.Thickness Tolerances, plus and minus,Ain.Strip Sheet8 in. andUnder in WidthOver 8to12 in.,incl, inWidthOver 12 to14 in.,incl, in WidthOver 14 to20 in.,incl, in WidthOver 20
45、to24 in.,incl, in WidthOver 24 to28 in.,incl, in WidthOver 28 to36 in.,incl, in WidthOver 36 to48 in.,incl, in WidthOver 48 to60 in.,incl, in Width0.004 and under 0.0003 0.0006 0.0006 . . . . . . . . . . . . . . . . . .Over 0.004 to 0.006, incl 0.0004 0.0008 0.0008 0.0013 . . . . . . . . . . . . . .
46、 .Over 0.006 to 0.009, incl 0.0006 0.0010 0.0010 0.0015 . . . . . . . . . . . . . . .Over 0.009 to 0.013, incl 0.0008 0.0013 0.0013 0.0018 0.0025 0.0025 0.003 0.0035 0.004Over 0.013 to 0.017, incl 0.0010 0.0015 0.0015 0.002 0.0025 0.0025 0.003 0.0035 0.0045Over 0.017 to 0.021, incl 0.0013 0.0018 0.0
47、018 0.002 0.003 0.003 0.0035 0.004 0.005Over 0.021 to 0.026, incl 0.0015 0.002 0.002 0.0025 0.003 0.003 0.0035 0.004 0.005Over 0.026 to 0.037, incl 0.002 0.002 0.002 0.0025 0.0035 0.0035 0.004 0.005 0.006Over 0.037 to 0.050, incl 0.002 0.0025 0.0025 0.003 0.004 0.004 0.005 0.006 0.007Over 0.050 to 0
48、.073, incl 0.0025 0.003 0.003 0.0035 0.005 0.005 0.006 0.007 0.008Over 0.073 to 0.130, incl 0.003 0.0035 0.0035 0.004 0.006 0.006 0.007 0.008 0.010Over 0.130 to 0.188, incl 0.0035 0.004 0.004 0.0045 0.007 0.007 0.008 0.010 0.012Rolled Bar PlateOver 0.188 to 0.205, incl 0.0035 0.004 0.004 0.0045 0.00
49、7 0.007 0.008 0.010 0.012Over 0.205 to 0.300, incl 0.004 0.0045 0.0045 0.005 0.009 0.009 0.010 0.012 0.014Over 0.300 to 0.500, incl 0.0045 0.005 0.005 0.006 0.012 0.012 0.013 0.015 0.018Over 0.500 to 0.750, incl 0.0055 0.007 0.007 0.009 0.015 0.015 0.017 0.019 0.023Over 0.750 to 1.00, incl 0.007 0.009 0.009 0.011 0.018 0.018 0.021 0.024 0.029Over 1.00 to 1.50, incl 0.022 0.022 0.022 0.022 0.022 0.022 0.025 0.029 0.036Over 1.50 to 2.00, incl 0.026 0.026 0.026 0.026 0.026 0.026 0.030 0.036 0.044AWhen tolerances are specified as all plus or all minus,
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1