ASTM B366-2010 Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings《工厂加工的锻制镍和镍合金配件的标准规范》.pdf

1、Designation: B366 10Standard Specification forFactory-Made Wrought Nickel and Nickel Alloy Fittings1This standard is issued under the fixed designation B366; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision

2、 A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers wrought welding fittings forpressure piping, factory-made from nickel and nickel alloys.Threaded fitting

3、s as covered in ASME B16.11 are also coveredby this specification. The term welding applies to butt-weldingor socket-welding parts such as 45 and 90 elbows, 180 bends,caps, tees, reducers, lap-joint stub ends, and other types, ascovered by ASME B16.9, ASME B16.11, MSS SP-43, MSSSP-95, and MSS SP-97.

4、1.1.1 Several grades of nickel and nickel alloys are includedin this specification. Grades are designated with a prefix, WPorCR, based on the applicable ASME or MSS dimensional andrating standards.1.1.2 Class WP fittings are those manufactured to therequirements of ASME B16.9, B16.11.1.1.3 For each

5、of the WP nickel and nickel alloy grades,several classes of fittings are covered to indicate whetherseamless or welded construction was utilized. Class designa-tions are also utilized to indicate the nondestructive test methodand extent of nondestructive examination (NDE). Table 1 isgeneral summary

6、of the fitting classes applicable to all WPgrades of nickel and nickel alloys covered by this specification.There are no classes for the CR grades. Specific requirementsare covered elsewhere.1.2 This specification does not apply to cast welding fit-tings.1.3 Optional supplementary requirements are p

7、rovided forfittings where a greater degree of examination is desired. Thesesupplementary requirements call for additional tests. Whendesired, one or more of these may be specified in the order.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses ar

8、e mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazard

9、s including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standa

10、rds:2B127 Specification for Nickel-Copper Alloy (UNSN04400) Plate, Sheet, and StripB160 Specification for Nickel Rod and BarB161 Specification for Nickel Seamless Pipe and TubeB162 Specification for Nickel Plate, Sheet, and StripB163 Specification for Seamless Nickel and Nickel AlloyCondenser and He

11、at-Exchanger TubesB164 Specification for Nickel-Copper Alloy Rod, Bar, andWireB165 Specification for Nickel-Copper Alloy (UNSN04400)* Seamless Pipe and TubeB166 Specification for Nickel-Chromium-Iron Alloys(UNS N06600, N06601, N06603, N06690, N06693,N06025, N06045, and N06696)* and Nickel-Chromium-C

12、obalt-Molybdenum Alloy (UNS N06617) Rod, Bar, andWireB167 Specification for Nickel-Chromium-Iron Alloys(UNS N06600, N06601, N06603, N06690, N06693,N06025, N06045, and N06696)* and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Seamless Pipeand TubeB168 Specification for Nickel-Chromium-Iron Al

13、loys(UNS N06600, N06601, N06603, N06690, N06693,1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Their Alloys.Current edition approved April 1, 2010. Published Ma

14、y 2010. Originallyapproved in 1961. Last previous edition approved in 2004 as B366 04b1. DOI:10.1520/B0366-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the st

15、andards Document Summary page onthe ASTM website.TABLE 1 Fitting Classes for WP GradesClass Construction Nondestructive ExaminationS Seamless NoneW Welded Radiography or UltrasonicWX Welded RadiographyWU Welded Ultrasonic1*A Summary of Changes section appears at the end of this standard.Copyright AS

16、TM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.N06025, N06045, and N06696) and Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617) Plate, Sheet,and StripB333 Specification for Nickel-Molybdenum Alloy Plate,Sheet, and StripB335 Specification for

17、 Nickel-Molybdenum Alloy RodB407 Specification for Nickel-Iron-Chromium Alloy Seam-less Pipe and TubeB408 Specification for Nickel-Iron-Chromium Alloy Rodand BarB409 Specification for Nickel-Iron-Chromium Alloy Plate,Sheet, and StripB423 Specification for Nickel-Iron-Chromium-Molybdenum-Copper Alloy

18、 (UNS N08825 and N08221)*Seamless Pipe and TubeB424 Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNSN08825 and UNS N08221)* Plate, Sheet, and StripB425 Specification for Ni-Fe-Cr-Mo-Cu Alloy (UNSN08825 and UNS N08221)* Rod and BarB434 Specification for Nickel-Molybdenum-Chromium-Iron Alloys (UNS N10003,

19、UNS N10242)* Plate, Sheet,and StripB435 Specification for UNS N06002, UNS N06230, UNSN12160, and UNS R30556 Plate, Sheet, and StripB443 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy(UNS N06625) and Nickel-Chromium-Molybdenum-SiliconAlloy (UNS N06219)* Plate, Sheet,and StripB444 Specif

20、ication for Nickel-Chromium-Molybdenum-Columbium Alloys (UNS N06625 and UNS N06852) andNickel-Chromium-Molybdenum-Silicon Alloy (UNSN06219) Pipe and TubeB446 Specification for Nickel-Chromium-Molybdenum-Columbium Alloy (UNS N06625), Nickel-Chromium-Molybdenum-Silicon Alloy (UNS N06219), and Nickel-C

21、hromium-Molybdenum-Tungsten Alloy (UNS N06650)*Rod and BarB462 Specification for Forged or Rolled UNS N06030,UNS N06022, UNS N06035, UNS N06200, UNS N06059,UNS N06686, UNS N08020, UNS N08024, UNS N08026,UNS N08367, UNS N10276, UNS N10665, UNS N10675,UNS N10629, UNS N08031, UNS N06045, UNS N06025,and UNS R20033 Alloy Pipe Flanges, Forged Fitting, or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).B366 109