ASTM B449-1993(2010)e1 Standard Specification for Chromates on Aluminum《铝的铬酸盐处理标准规范》.pdf

1、Designation: B449 93 (Reapproved 2010)1Standard Specification forChromates on Aluminum1This standard is issued under the fixed designation B449; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、 parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1NOTEUpdated format of the military specification in Section 2.4 editoriall

3、y in June 2010.1. Scope1.1 This specification covers the requirements relating torinsed and nonrinsed chromate conversion coatings on alumi-num and aluminum alloys intended to give protection againstcorrosion and as a base for other coatings. This edition of thespecification has been coordinated wit

4、h ISO/DIS 10546 and istechnically equivalent.1.2 Aluminum and aluminum alloys are chromate coated inorder to retard corrosion; as a base for organic films includingpaints, plastics, and adhesives; and as a protective coatinghaving a low electrical contact impedance.1.3 The values stated in SI units

5、are to be regarded asstandard. No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practic

6、es and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B117 Practice for Operating Salt Spray (Fog) ApparatusB602 Test Method for Attribute Sampling of Metallic andInorganic CoatingsB767 Guide for Determining Mass Per Unit Area of Elec-t

7、rodeposited and Related Coatings by Gravimetric andOther Chemical Analysis ProceduresD1730 Practices for Preparation of Aluminum andAluminum-Alloy Surfaces for PaintingD3359 Test Methods for Measuring Adhesion by Tape Test2.2 ISO Standards:3ISO 2409 Paint and VarnishesCross-Cut TestISO 3768 Metallic

8、 CoatingsNeutral Salt Spray Test(NSS Test)ISO 3892 Conversion Coatings on Metallic MaterialsDetermination of Mass Per Unit AreaGravimetricMethodISO 4519 Electrodeposited Metallic Coatings and RelatedFinishesSampling Procedures for Inspection by At-tributesISO/DIS 10546 Chemical Conversion CoatingsRi

9、nsedand Nonrinsed Chromate Conversion CoatingsOn Alu-minum and Aluminum Alloys2.3 Federal Standard:4Fed. Std. No. 141 Paints, Varnish, Lacquer, and RelatedMaterials; Methods of Inspection2.4 Military Specification:4MIL-DTL-5541 Chemical Films for Aluminum and Alumi-num Alloys3. Terminology3.1 Defini

10、tions:3.1.1 nonrinsedchromate coatings that are dried immedi-ately after the chromating step without receiving a water rinse.3.1.1.1 DiscussionThis special type of coating is typicallyused on long coils of aluminum sheet stock that receive animmediate subsequent paint or adhesive coating.NOTE 1Nonri

11、nsed chromate coatings are finding increased usage onfabricated parts and castings.3.1.2 rinsedchromate coatings that are rinsed in waterprior to drying.3.1.2.1 DiscussionThis type of coating is typically ap-plied to extruded aluminum fabricated parts and castings.1This specification is under the ju

12、risdiction of ASTM Committee B08 onMetallic and Inorganic Coatings and is the direct responsibility of SubcommitteeB08.07 on Conversion Coatings.Current edition approved April 1, 2010. Published June 2010. Originallyapproved in 1967. Last previous edition approved in 2004 as B449 93 (2004).DOI: 10.1

13、520/B0449-93R10E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standard

14、s Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA

15、 19428-2959, United States.4. Classification4.1 Chromate finishes can be applied ranging in color frombrown, thick coatings (Class 1) providing maximum corrosionprotection to yellow, intermediate thickness coatings (Class 2)suitable as an organic film base or to colorless, thin coatings(Class 3) sui

16、table for low electrical contact resistance. Theyellow coatings vary from golden yellow to iridescent lightyellow. Chromate-phosphate finishes (Class 4) can be appliedranging in color from green to iridescent light green. The Class4 coatings comply with the requirements of MIL-DTL-5541.4.2 Finishers

17、 can seldom guarantee to supply exact shadesof color with chromate conversion coatings. If it is necessary tohave exact shades of color, it is possible to dye chromatecoatings having a coating mass greater than 0.4 g/m2to obtaina wide range of colors, but they can only be expected to givean order of

18、 added corrosion resistance similar to that providedby the undyed coatings. It should be noted that color and coloruniformity will vary somewhat between one alloy and anotherand from a polished surface to an etched surface. Iridescenceand variations in color density from one area of the surface toan

19、other are normal and shall not be considered a sign of poorquality.4.3 The finishes are divided into four classes; their mostimportant characteristics are listed in Table 1.5. Surfaces Preparation5.1 The surfaces of the parts to be chromated must be cleanand free of any oxidation, scale, or soils su

20、ch as metal turnings,grinding dust, oil, grease, lubricants, hand-sweat, or any othercontamination detrimental to the chromating process. The partsmust therefore, as far as necessary, be cleaned before chromat-ing and if necessary be pickled. Fig. X2.1 shows the variousprocessing step options.6. Met

21、hods of Application of Chromate Coatings6.1 Metallic material other than aluminum should not betreated with the parts to be chromated.6.2 Chromate conversion coatings are normally applied bydipping: the coating may also be applied by inundation,spraying, roller coating, or by wipe-on techniques. The

22、 appli-cation method used should be taken from the operatinginstructions for the chromating process employed. Chromatingsolutions are usually acidic and may contain hexavalentchromium salts together with other salts that may be varied toaffect the appearance and hardness of the film. The color of th

23、efilm, and, therefore, the type of conversion coating, depends onthe composition of the chromating solution, but it is alsoaffected by the pH and temperature, the duration of thetreatment, and the nature and surface condition of the alloybeing treated.6.3 These coatings receive a final water rinse.

24、If the coatingis meant to be a basis for additional coatings, the detail shall besubject to a rinse in deionized water with a conductivity lessthan 100t S/cm. If hot water is used as the final rinse after thechromating process, it is essential that the time of rinsingshould be kept as short as possi

25、ble in order to prevent thedissolution of the hexavalent chromium. The drying of thecoating shall be carried out at a temperature not exceeding60C to prevent cracking due to dehydration, which causes lossof adhesion and performance of the chromate coating.6.4 Any additional subsequent treatments dep

26、end upon thepurpose for which the chromated parts are intended.7. Coating Requirements7.1 GeneralChromate conversion coatings harden withage by gradual dehydration. They should, therefore, be handledcarefully for the first 24 h after treatment, and any tests(including corrosion tests) shall be defer

27、red until the expirationof that period. The green chromate-phosphate coatings usuallycontinue to improve in corrosion resistance after initial forma-tion. They achieve their maximum corrosion resistance after 1to 2 months at room temperature. It is not required to storeparts for this purpose.7.2 Ele

28、ctrical ResistanceColorless, light yellow, or lightgreen iridescent chromate layers of low mass per unit areaincrease the electrical resistance between an electrical contactand the aluminum to a very small extent. When measured at9-V and a 2-A current the resistance should be less than 0.1 V.Highly

29、colored brown, yellow, or green coatings show amarked increase in electrical contact resistance with increasingmass per unit area of the chromate layer and may reachresistances of 10 000 V or more.7.3 AdhesionThe coatings shall be adherent and non-powdery. There are no practical tests for measuring

30、theadhesion of a chromate conversion coating on aluminum.However, a practical evaluation of the adhesion can be madeby measuring the adhesion of a secondary organic film appliedto the chromated aluminum. When specified, the chromateconversion coating shall pass the organic coating adhesion testin Te

31、st Methods D3359 or the equivalent ISO 2409.7.3.1 Class 4 coatings intended for use under MIL-DTL-5541 shall have their adhesion evaluated by Method 6301 ofFed. Std. No. 141.7.3.2 Additional treatments applied under MIL-DTL-5541can be found in Practices D1730, Methods 5, 6, and 7.7.4 Corrosion Resis

32、tanceWhen subjected to the neutralsalt spray test specified in Practice B117 or in the equivalentISO 3768, three separate test specimens of the coating shallwithstand exposure for the hours shown in Table 2 withoutgiving evidence, to the unaided eye, of more than a total of 8isolated spots or pits.

33、None shall be larger than 1 mm indiameter. Each individual test specimen shall not have moreTABLE 1 Classification of Chromate CoatingsClassAAppearanceCoating Mass perUnit Area, g/m2Corrosion Protection1 yellow to brown 0.4 to 2 maximum corrosion resistancegenerally used as final finish2 colorless t

34、o yellow 0.1 to 0.4 moderate corrosion resistance,used as a paint base and forbonding to rubber3 colorless 1 %1 500 336 482 250 168 243 168 120 124 500 336 48AClass numbers are assigned on the basis of traditional usage and do notreflect a ranking of corrosion resistance.BThe exposure times are indi

35、cative of the relative corrosion resistance of thevarious coating classes on the different alloys, but no direct relationship existsbetween performance in the neutral salt spray test and performance in service.B449 93 (2010)13The resulting solution is filtered, and 25 mL of the filtrate areacidified

36、 with approximately 38 % nitric acid then 10 mLammonium molybdate reagent and 5 g ammonium nitrate areadded. The sample is allowed to stand for at least 15 min. Ayellow precipitate shows the presence of phosphate. The leastquantity of phosphate detectable by this process corresponds toabout 40 mg P2

37、O5per square metre of surface.X1.4 Testing for ZincX1.4.1 To test for the presence of zinc in the layer, a sampleis taken whose surface to be tested is about 100 cm2; this istreated with 50 mL of approximately 65 % nitric acid at roomtemperature until the layer is either completely dissolved or atle

38、ast until the surface has clearly been attacked. The resultingsolution is filtered through glass wool, and 25 mL of the filtrateare neutralized with 20 % caustic soda until phenolphthaleinindicator gives a red coloration. The solution is then weaklyacidified by addition of about 10 drops of 25 % sul

39、furic acid.After addition of 5 mL of 5 % potassium ferrocyanide solution,a greenish-white precipitate shows the presence of zinc. Theleast quantity of zinc detectable by this process corresponds toabout 20 mg zinc per square metre of surface.X2. TREATMENT SEQUENCE OPTIONSX2.1 The chromate process ne

40、cessitates a specified se-quence of treatments that depends upon the surface conditionof the parts to be treated, the aluminum alloy used, and thedesired appearance of the parts. See Fig. X2.1.FIG. X2.1 Treatment Stages of the Chromating of Aluminum andAluminum AlloysB449 93 (2010)14ASTM Internation

41、al takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their

42、own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be

43、addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,

44、 at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).B449 93 (2010)15