ASTM B483 B483M-2013e1 Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Drawn Pipe for General Purpose Applications《一般用途的铝和铝合金冷拔管和拉制管的标准规格》.pdf

1、Designation: B483/B483M 131Standard Specification forAluminum and Aluminum-Alloy Drawn Tube and Drawn Pipefor General Purpose Applications1This standard is issued under the fixed designation B483/B483M; the number immediately following the designation indicates the yearof original adoption or, in th

2、e case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTETable 1 was corrected editorially in June 2014.1. Scope*1.1 This specification covers aluminu

3、m and aluminum-alloydrawn tube and drawnpipe in straight lengths and tube in coilsfor general purpose applications in the alloys (Note 2), andtempers shown in Tables 1 and 2. Coiled tubes are generallyavailable only as round tubes with a wall thickness notexceeding 0.083 in. 2.00 mm and only in non-

4、heat-treatablealloys.NOTE 1For drawn seamless tubes, see Specifications B210 andB210M, for tubes to be used in condensers and heat exchangers,Specifications B234 and B234M, and for seamless pipe, SpecificationB241/B241M. For extruded structural tube and pipe, see SpecificationB429.NOTE 2this specifi

5、cation use of the term alloy in the general senseincludes aluminum as well as aluminum alloy.1.2 Alloy and temper designations are in accordance withANSI H35.1/H35.1(M). The equivalent Unified Number Sys-tem alloy designations are those of Table 3 preceded byA9, forexample A91060 for aluminum 1060 i

6、n accordance withPractice E527.1.3 For acceptance criteria for inclusion of new aluminumand aluminum alloys in this specification, see Annex A2.1.4 The values stated in either inch-pound units or SI unitsare to be regarded separately as standard. Within the text, theSI units are shown in brackets. T

7、he values stated in eachsystem may not be exact equivalents; therefore, each systemshall be used independently of the other. Combining valuesfrom the two systems may result in nonconformance with thestandard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated

8、with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on dateof order acceptance form a

9、 part of this specification to theextent referenced herein:2.2 ASTM Standards:2B210 Specification for Aluminum and Aluminum-AlloyDrawn Seamless TubesB210M Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes (Metric)B234 Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes

10、for Condensers and Heat Ex-changersB234M Specification for Aluminum and Aluminum-AlloyDrawn Seamless Tubes for Condensers and Heat Ex-changers (Metric)B241/B241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded TubeB429 Specification forAluminum-Alloy Extruded Struct

11、uralPipe and TubeB557 Test Methods for Tension Testing Wrought and CastAluminum- and Magnesium-Alloy ProductsB557M Test Methods for Tension Testing Wrought and CastAluminum- and Magnesium-Alloy Products (Metric)B597 Practice for Heat Treatment of Aluminum Alloys(Withdrawn 2002)3B660 Practices for Pa

12、ckaging/Packing of Aluminum andMagnesium ProductsB666/B666M Practice for Identification Marking of Alumi-num and Magnesium ProductsB881 Terminology Relating to Aluminum- and Magnesium-Alloy ProductsB918 Practice for Heat Treatment of Wrought AluminumAlloysE29 Practice for Using Significant Digits in

13、 Test Data to1This specification is under the jurisdiction of ASTM Committee B07 on LightMetals and Alloys and is the direct responsibility of Subcommittee B07.03 onAluminum Alloy Wrought Products.Current edition approved May 1, 2013. Published June 2013. Originallyapproved in 1983. Last previous ed

14、ition approved in 2003 as B483/B483M03,which was withdrawn January 2012 and reinstated in May 2013. DOI: 10.1520/B0483_B0483M-13E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume inform

15、ation, refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohoc

16、ken, PA 19428-2959. United States1TABLE 1 Tensile Property Limits, TubeA,BALLOYANDTEMPERSPECIFIED WALLTHICKNESSin. mmTENSILE STRENGTH - ksi MPaElongation in 2 in. 50 mm or4 Diameter,Cmin, %JULTIMATEYIELDD(0.2% Offset),ksi MPaFULLSECTIONSPECIMENECut-Out SpecimenFmin. max. min. max. In 50 mmIn 5Diamet

17、er(5.65=A)G1060F,I1060-O 0.010-0.500 0.25-12.50 8.5 60 13.5 95 2.5 15 . . . . . . . . . .1060-H12 0.010-0.500 0.25-12.50 10.0 70 . . . . 4.0 30 . . . . . . . . . .1060-H14 0.010-0.500 0.25-12.50 12.0 85 . . . . 10.0 70 . . . . . . . . . .1060-H18 0.010-0.500 0.25-12.50 16.0 110 . . . . 13.0 90 . . .

18、 . . . . . . .1060-H113K0.010-0.500 .025-12.50 8.5 60 . . . . 2.5 15 . . . . . . . . . .1100F,I1100-O 0.014-0.500 0.36-12.50 11.0 75 15.5 105 3.5 25 . . . . . . . . . .1100-H12 0.014-0.500 0.36-12.50 14.0 95 . . . . 11.0 75 . . . . . . . . . .1100-H14 0.014-0.500 0.36-12.50 16.0 110 . . . . 14.0 95

19、. . . . . . . . . .1100-H16 0.014-0.500 0.36-12.50 19.0 130 . . . . 17.0 115 . . . . . . . . . .1100-H18 0.014-0.500 0.36-12.50 22.0 150 . . . . 20.0 140 . . . . . . . . . .1100-H113K0.014-0.500 0.36-12.50 11.0 75 . . . . 3.5 25 . . . . . . . . . .3003F,I3003-O0.010-0.024 0.25-0.63 14.0 95 19.0 130

20、5.0 35 . . . . . . . . . .0.025-0.049 0.63-1.20 14.0 95 19.0 130 5.0 35 . . . . 30 20 . .0.050-0.259 1.20-6.30 14.0 95 19.0 130 5.0 35 . . . . 35 25 . .0.260-0.500 6.30-12.50 14.0 95 19.0 130 5.0 35 . . . . . . 30 273003-H12 0.010-0.500 0.25-12.50 17.0 115 . . . . 12.0 85 . . . . . . . .3003-H140.01

21、0-0.024 0.25-0.63 20.0 140 . . . . 17.0 115 . . . . 3 . . . .0.025-0.049 0.63-1.20 20.0 140 . . . . 17.0 115 . . . . 5 3 . .0.050-0.259 1.20-6.30 20.0 140 . . . . 17.0 115 . . . . 8 4 . .0.260-0.500 6.30-12.50 20.0 140 . . . . 17.0 115 . . . . . . . . . .3003-H160.010-0.024 0.25-0.63 24.0 165 . . .

22、. 21.0 145 . . . . . . . . . .0.025-0.049 0.63-1.20 24.0 165 . . . . 21.0 145 . . . . 3 2 . .0.050-0.259 1.20-6.30 24.0 165 . . . . 21.0 145 . . . . 5 4 . .0.260-0.500 6.30-12.50 24.0 165 . . . . 21.0 145 . . . . . . . . . .3003-H180.010-0.024 0.25-0.63 27.0 185 . . 24.0 165 . . . . 2 . . . .0.025-0

23、.049 0.63-1.20 27.0 185 . . . . 24.0 165 . . . . 3 2 . .0.050-0.259 1.20-6.30 27.0 185 . . . . 24.0 165 . . . . 5 3 . .0.260-0.500 6.30-12.50 27.0 185 . . . . 24.0 165 . . . . . . . . . .3003-H113K0.010-0.500 0.25-12.50 14.0 95 . . . . 5.0 35 . . . . . . . .5050F,I5050-O 0.010-0.500 0.25-12.70 18.0

24、125 24.0 165 6.0 40 . . . . . . . . . .5050-H32 0.010-0.500 0.25-12.70 22.0 150 . . . . 16.0 110 . . . . . . . . . .5050-H34 0.010-0.500 0.25-12.70 25.0 170 . . . . 20.0 140 . . . . . . . . . .5050-H36 0.010-0.500 0.25-12.70 27.0 185 . . . . 22.0 150 . . . . . . . . . .5050-H38 0.010-0.500 0.25-12.7

25、0 29.0 200 . . . . 24.0 165 . . . . . . . . . .5052F,I5052-O 0.010-0.450 0.25-11.50 25.0 170 35.0 240 10.0 70 . . . . . . . . . .5052-H32 0.010-0.450 0.25-11.50 31.0 215 . . . . 23.0 160 . . . . . . . . . .5052-H34 0.010-0.450 0.25-11.50 34.0 235 . . . . 26.0 180 . . . . . . . . . .5052-H36 0.010-0.

26、450 0.25-11.50 37.0 255 . . . . 29.0 200 . . . . . . . . . .5052-H38 0.010-0.450 0.25-11.50 39.0 270 . . . . 31.0 215 . . . . . . . . . .60616061-O 0.018-0.500 0.45-12.50 . . . . 22.0 150 . . . . 14.0 95 15 15 136061-T40.025-0.049 0.63-1.20 30.0 200 . . . . 16.0 110 . . . . 16 14 . .0.050-0.259 1.20

27、-6.30 30.0 200 . . . . 16.0 110 . . . . 18 16 . .0.260-0.500 6.30-12.50 30.0 200 . . . . 16.0 110 . . . . 20 18 166061-T42G,H0.025-0.049 0.63-1.20 30.0 200 . . . . 14.0 110 . . . . 16 14 . .0.050-0.259 1.20-6.30 30.0 200 . . . . 14.0 110 . . . . 18 16 . .0.260-0.500 6.30-12.50 30.0 200 . . . . 14.0

28、110 . . . . 20 18 166061-T6 andT62G,H0.025-0.049 0.63-1.20 42.0 290 . . . . 35.0 240 . . . . 10 8 . .0.050-0.259 1.20-6.30 42.0 290 . . . . 35.0 240 . . . . 12 10 . .0.260-0.500 6.30-12.50 42.0 290 . . . . 35.0 240 . . . . 14 12 1060636063-O 0.018-0.500 0.45-12.50 . . . . 19.0 130 . . . . . . . . .

29、. . . . .6063-T4 andT42G,H0.025-0.049 0.63-1.20 22.0 150 . . . . 10.0 70 . . . . 16 14 . .0.050-0.259 1.20-6.30 22.0 150 . . . . 10.0 70 . . . . 18 16 . .0.260-0.500 6.30-12.50 22.0 150 . . . . 10.0 70 . . . . 20 18 166063-T6 andT62G,H0.025-0.049 0.63-1.20 33.0 230 . . . . 28.0 195 . . . . 12 8 . .0

30、.050-0.259 1.20-6.30 33.0 230 . . . . 28.0 195 . . . . 14 10 . .0.260-0.500 6.30-12.50 33.0 230 . . . . 28.0 195 . . . . 16 12 106063-T83 0.025-0.259 0.63-6.30 33.0 230 . . . . 30.0 205 . . . . 5 . . . .6063-T831 0.025-0.259 0.63-6.30 28.0 195 . . . . 25.0 170 . . . . 5 . . . .B483/B483M 1312Determi

31、ne Conformance with SpecificationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE215 Practice for Standardizing Equipment for Electromag-netic Testing of Seamless Aluminum-Alloy TubeE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)E607 Tes

32、t Method for Atomic Emission SpectrometricAnalysis Aluminum Alloys by the Point to Plane Tech-nique Nitrogen Atmosphere (Withdrawn 2011)3TABLE 1 ContinuedALLOYANDTEMPERSPECIFIED WALLTHICKNESSin. mmTENSILE STRENGTH - ksi MPaElongation in 2 in. 50 mm or4 Diameter,Cmin, %JULTIMATEYIELDD(0.2% Offset),ks

33、i MPaFULLSECTIONSPECIMENECut-Out SpecimenFmin. max. min. max. In 50 mmIn 5Diameter(5.65=A)G6063-T8320.025-0.049 0.63-1.20 41.0 285 . . . . 36.0 250 . . . . 8 5 . .0.050-0.259 1.20-6.30 40.0 275 . . . . 35.0 240 . . . . 8 5 . .62626262-T6 andT62G,H0.025-0.049 0.63-1.20 42.0 290 . . . . 35.0 240 . . .

34、 . 10 8 . .0.050-0.259 1.20-6.30 42.0 290 . . . . 35.0 240 . . . . 12 10 . .0.260-0.500 6.30-12.50 42.0 290 . . . . 35.0 240 . . . . 14 12 106262-T9 0.025-0.375 0.63-10.00 48.0 330 . . . . 44.0 305 . . . . 5 4 3ASee Annex A1.BTo determine conformance to this specification each value for tensile stre

35、ngth and for yield strength shall be rounded to the nearest 0.1 ksi MPa and each value forelongation to the nearest 0.5 %, both in accordance with the rounding method of Practice E29.CElongation of full-section and cut-out sheet-type specimens is measured in 2 in.; of cut-out round specimens, in 4 s

36、pecimen diameter.DYield strength to be determined only on straight tube.ERound tube 2 inches or less in outside diameter and square tube 112 inches or less on a side are tested in full section unless the limitations of the testing machineprecludes the use of such a specimen.FFor round tube over 2 in

37、ches in diameter, for square tube over 112 inches on a side, for all sizes of tube other than round and square, or in those cases when a full sectionspecimen cannot be used, a cut-out specimen is used.GElongations in 50 mm apply for tube tested in full-section, for sheet type specimens for tubes hav

38、ing a flat wall, and for similar curved specimens for tubes having a curvedwall up to a maximum wall thickness of 12.50 mm. Elongations in 5D (5.65 =A), where D and A are diameter and cross-sectional area specimens, respectively, apply toround test specimens machined from wall thickness over 6.30 mm

39、.HMaterial in the T42 or T62 tempers is not available from the material producers.IIn this alloy tube other than round is produced only in the F (as drawn) and O tempers. Properties for F temper are not specified or guaranteed.JFor specified wall thickness under 0.025 in. 0.63 mm elongation is not r

40、equired.KThe H113 temper applies to other than round tube which is fabricated from annealed round tube. Corrected editorially.TABLE 2 Tensile Property Limits, Drawn PipeA,B,CTemperPipe Size,DesignationTensile Strength, ksi MPaYield StrengthC(0.2% Offset),ksi MPa,minElongation, min, %min maxElongatio

41、nin 2 in. or4 Diameter,Dmin, %In50 mmIn5 Diameter(5.65 =A)EAlloy 3003H18 Under 1 27.0 185 . 24.0 165 4 4 .H112 1 and over 14.0 95 . 5.0 35 25 25 22AThe basis for establishment of tensile property limits is shown in Annex A1.BFor purposes of determining conformance with this specification, each value

42、 for tensile strength and yield strength shall be rounded to the nearest 0.1 ksi, and each valuefor elongation shall be rounded to the nearest 0.5 %, both in accordance with the rounding-off method of Practice E29.CElongation of full-section and cut-out sheet-type specimens is measured in 2 in.; of

43、round specimens, in 4 specimen diameter.DFor purposes of determining conformance with this specification, each value for ultimate strength and yield strength shall be rounded to the nearest 1 MPa, and eachvalue for elongation shall be rounded to the nearest 0.5%, both in accordance with the rounding

44、-off method of Practice E29.EElongation in 50 mm apply for pipe tested in full-section and to sheet type specimens taken from pipes having a wall up to 12.50 mm thick. Elongation in 5D (5.65 =A)where D and A are diameter and cross-sectional area of the specimens respectively, apply to round test spe

45、cimens machined from wall thicknesses over 6.30 mm.B483/B483M 1313E716 Practices for Sampling and Sample Preparation ofAluminum and Aluminum Alloys for Determination ofChemical Composition by Spectrochemical AnalysisE1251 Test Method for Analysis of Aluminum and Alumi-num Alloys by Spark Atomic Emis

46、sion Spectrometry2.3 ANSI Standards:4H35.1/H35.1(M) Alloy and Temper Designation SystemsH35.2 Dimensional Tolerances for Aluminum Mill ProductsH35.2M Dimensional Tolerances for Aluminum Mill Prod-ucts Metric2.4 Military Standard:5MIL-STD-129 Marking for Shipment and Storage2.5 Military Specification

47、s:5AMS 2770 Heat Treatment of Wrought Aluminum AlloyPartsAMS 2772 Heat Treatment of Aluminum Alloy Raw Mate-rials2.6 Federal Standard:5Fed. Std. No. 123 Marking for Shipment (Civil Agencies)3. Terminology3.1 DefinitionsRefer to Terminology B881 for definitionsof product terms used in this specification.4. Ordering Information4.1 Orders for material to this specification shall include thefollowing information:4.1.1 This specification designation (which includes thenumber, the year, an