ASTM B517-2005(2014) Standard Specification for Welded Nickel-Chromium-Iron-Alloy &40 UNS N06600 UNS N06603 UNS N06025 and UNS N06045&41 Pipe《焊接的镍铬铁合金 (UNS N06600 UNS N06603 UNS N0.pdf

1、Designation: B517 05 (Reapproved 2014)Standard Specification forWelded Nickel-Chromium-Iron-Alloy (UNS N06600, UNSN06603, UNS N06025, and UNS N06045) Pipe1This standard is issued under the fixed designation B517; the number immediately following the designation indicates the year oforiginal adoption

2、 or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification2covers welded, cold-worked, andannealed nickel-chromium-i

3、ron alloy (UNS N06600,3N06603,N06025, and N06045) pipe for general corrosive service andheat-resisting applications.1.2 This specification covers outside diameter and nominalwall pipe shown in ANSI B36.19. Pipe having other dimen-sions may be furnished provided such pipe complies with allother requi

4、rements of this specification.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of th

5、esafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriate

6、safety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:4B775 Specification for General Requirements for Nickel andNickel Alloy Welded PipeB899 Terminology Relating to Non-ferrous Metals and Al-loys2.2 ANSI Standard

7、:B36.19 Stainless Steel Pipe53. Terminology3.1 Terms defined in Terminology B899 shall apply unlessdefined otherwise in this standard.4. General Requirement4.1 Material furnished in accordance with this specificationshall conform to the applicable requirements of the currentedition of Specification

8、B775 unless otherwise providedherein.5. Ordering Information5.1 It is the responsibility of the purchaser to specify allrequirements that are necessary for the safe and satisfactoryperformance of material ordered under this specification.Examples of such requirements include, but are not limited to,

9、the following:5.1.1 Alloy name or UNS number.5.1.2 ASTM designation and year of issue.5.1.3 Condition (temper).5.1.4 Dimensions:5.1.4.1 Nominal pipe size or outside diameter and schedulenumber or nominal wall thickness.5.1.4.2 Length (specific or random).5.1.5 Quantity (feet or metres, or number of

10、pieces).5.1.6 CertificationState if certification or a report of testresults is required.5.1.7 Samples for Product (Check) AnalysisState whethersamples for product (check) analysis should be furnished.5.1.8 Purchaser InspectionIf the purchaser wishes towitness tests or inspection of material at the

11、place ofmanufacture, the purchase order must so state indicating whichtests or inspections are to be witnessed.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.07 on Refined Nickel and Cobalt and Th

12、eir Alloys.Current edition approved Oct. 1, 2014. Published October 2014. Originallyapproved in 1970. Last previous edition approved in 2009 as B517 05 (2009).DOI: 10.1520/B0517-05R14.2For ASME Boiler and Pressure Code applications see related SpecificationSB-517 in Section II of that Code.3New desi

13、gnation established in accordance with ASTM E527 and SAE J1086,Practice for Numbering Metals and Alloys (UNS).4For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the st

14、andards Document Summary page onthe ASTM website.5Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box

15、 C700, West Conshohocken, PA 19428-2959. United States16. Materials and Manufacture6.1 Pipe shall be made from flat-rolled alloy by an auto-matic welding process with no addition of filler metal. Subse-quent to welding and prior to final heat treatment, the materialshall be cold worked either in bot

16、h weld and base metal or inweld metal only.6.2 Pipe shall be furnished with a scale-free finish. Whenbright annealing is used, descaling is not necessary.7. Chemical Composition7.1 The material shall conform to the requirements as tochemical composition prescribed in Table 1.7.2 If a product (check)

17、 analysis is performed by thepurchaser, the material shall conform to the product (check)analysis variations in Specification B775.8. Mechanical and Other Requirements8.1 Mechanical PropertiesThe material shall conform tothe requirements for mechanical properties prescribed in Table2.8.2 Flattening

18、TestPipe shall be capable of withstanding,without cracking, flattening under a load applied gradually atroom temperature until the distance between the platens is fivetimes the wall thickness. The weld shall be positioned 90 fromthe direction of the applied flattening force.8.3 Nondestructive Test R

19、equirements:8.3.1 Category 1Each piece of each lot shall be subject toone of the following four tests: hydrostatic, pneumatic (airunderwater), eddy current, or ultrasonic.8.3.2 Category 2Each piece in each lot shall be subjectedto a leak test and an electric test as follows:8.3.2.1 Leak TestHydrosta

20、tic or pneumatic (air underwa-ter).8.3.2.2 Electric TestEddy current or ultrasonic.8.4 The manufacturer shall have the option to test Category1 or Category 2 and select the nondestructive test methods, ifnot specified by the purchaser.8.5 Transverse Guided Bend TestAt the option of the pipemanufactu

21、rer, the transverse guided bend test may be substi-tuted in lieu of the flattening test. Two bend specimens shall betaken transversely from pipe or the test specimens may betaken from a test plate of the same material and heat as pipe,which is attached to the end of the cylinder and welded as aprolo

22、ngation of the pipe longitudinal seam. One test is requiredfor each lot as defined in Specification B775.9. Number of Tests9.1 Chemical AnalysisOne per lot.9.2 Mechanical PropertiesOne test per lot.9.3 Flattening or Transverse Guided Bend TestOne testper lot.9.4 NondestructiveEach piece in each lot.

23、10. Keywords10.1 welded pipe; N06600; N06603; N06025; N06045TABLE 1 Chemical RequirementsElementCompositionLimits, %Product (Check) AnalysisVariations, under min orover max, of theSpecified Limit of ElementN06600 N06603 N06025 N06045NickelA72.0 min Bal Bal 45.0 min 0.45Chromium 14.0 min 24.026.0 24.

24、026.0 26.029.0 0.1517.0 max 0.25Iron 6.0 min 8.011.0 8.011.0 21.025.0 0.1010.0 max 0.10Manganese 1.0 0.15 max 0.15 max 1.0 max 0.03Carbon 0.15 max 20.0-40.0 0.150.25 0.050.12 0.01Copper 0.5 max 0.50 max 0.10 max 0.3 max 0.03Silicon 0.5 max 0.50 max 0.5 max 2.53.0 0.03Sulfur 0.015 max 0.010 max 0.010

25、 max 0.010 max 0.003Aluminum . 2.4-3.0 1.82.4 .Titanium . 0.010.25 0.10.2 .Phosphorus . 0.020 max 0.02 max 0.02 maxZirconium . 0.010.40 0.010.10 .Yttrium . 0.010.15 0.050.12 .Cerium . . . 0.030.09ANickel shall be determined arithmetically by difference.TABLE 2 Mechanical Property RequirementsAlloyTe

26、nsile Strength,min,psi (MPa)Yield Strength,0.2 % Offset,min, psi (MPa)Elongation in 2 in.or 50 mm,min, %N06600 80 000 (550) 35 000 (240) 30N06603 94 000 (650) 43 000 (300) 25N06025 98 000 (680) 39 000 (270) 30N06045 90 000 (620) 35 000 (240) 30B517 05 (2014)2ASTM International takes no position resp

27、ecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This s

28、tandard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM Interna

29、tional Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown bel

30、ow.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 05 (2014)3