ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:103.73KB ,
资源ID:461821      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-461821.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM B634-1988(2009) Standard Specification for Electrodeposited Coatings of Rhodium for Engineering Use《工程用铑电解沉积镀层的标准规范》.pdf)为本站会员(arrownail386)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM B634-1988(2009) Standard Specification for Electrodeposited Coatings of Rhodium for Engineering Use《工程用铑电解沉积镀层的标准规范》.pdf

1、Designation: B634 88 (Reapproved 2009)Standard Specification forElectrodeposited Coatings of Rhodium for Engineering Use1This standard is issued under the fixed designation B634; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers requirements for electrodepos-ited coatings of rhodium used for engineering purposes

3、.1.2 Coatings of rhodium covered by this specification areusually employed for their corrosion resistance, stable electri-cal contact resistance, wear resistance, reflectivity, and heatresistance.1.3 Appendix X1 covers some typical applications forelectrodeposited rhodium.1.4 The values stated in SI

4、 units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health

5、practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 The following documents form a part of this documentto the extent referenced herein.2.2 ASTM Standards:2B183 Practice for Preparation of Low-Carbon Steel forElectroplatingB242 Guide for Prepa

6、ration of High-Carbon Steel for Elec-troplatingB252 Guide for Preparation of Zinc Alloy Die Castings forElectroplating and Conversion CoatingsB254 Practice for Preparation of and Electroplating onStainless SteelB281 Practice for Preparation of Copper and Copper-BaseAlloys for Electroplating and Conv

7、ersion CoatingsB322 Guide for Cleaning Metals Prior to ElectroplatingB343 Practice for Preparation of Nickel for Electroplatingwith NickelB456 Specification for Electrodeposited Coatings of Cop-per Plus Nickel Plus Chromium and Nickel Plus Chro-miumB481 Practice for Preparation of Titanium and Titan

8、iumAlloys for ElectroplatingB482 Practice for Preparation of Tungsten and TungstenAlloys for ElectroplatingB487 Test Method for Measurement of Metal and OxideCoating Thickness by Microscopical Examination of CrossSectionB507 Practice for Design of Articles to Be Electroplated onRacksB567 Test Method

9、 for Measurement of Coating Thicknessby the Beta Backscatter MethodB568 Test Method for Measurement of Coating Thicknessby X-Ray SpectrometryB571 Practice for Qualitative Adhesion Testing of MetallicCoatingsB602 Test Method for Attribute Sampling of Metallic andInorganic CoatingsB697 Guide for Selec

10、tion of Sampling Plans for Inspectionof Electrodeposited Metallic and Inorganic CoatingsB762 Test Method of Variables Sampling of Metallic andInorganic CoatingsE8 Test Methods for Tension Testing of Metallic Materials2.3 Military Standards:MIL-R-46085 Rhodium Plating, Electrodeposited3QQ-N-290 Nicke

11、l Plating, Electrodeposited33. Classification3.1 Electrodeposited coatings of rhodium on the basis ofthickness are classified as follows:Class Minimum Thickness, m0.05 0.050.25 0.250.5 0.5112.5 2.51This specification is under the jurisdiction of ASTM Committee B08 on and isthe direct responsibility

12、of Subcommittee B08.08.02 on Precious Metal Coatings.Current edition approved Sept. 1, 2009. Published November 2009. Originallyapproved in 1978. Last previous edition approved in 2004 as B634 88 (2004)1.DOI: 10.1520/B0634-88R09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, o

13、rcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.1

14、Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.2 6.254. Ordering Information4.1 To make application of this standard complete, thepurchaser needs to supply the following information to theseller in the purchase order or other gover

15、ning document:4.1.1 Name, designation, and year of issue of this standard,4.1.2 Class including a maximum thickness, if appropriate(3.1),4.1.3 Nature of substrate, for example, high strength steel,need for stress relief, undercoats, embrittlement relief (5.1, 5.2,5.3),4.1.4 Significant surfaces (6.2

16、),4.1.5 Appearance (6.3),4.1.6 Requirements and methods of testing for one or moreof the following requirements: need for and type of testspecimens (8.1); thickness (8.2); adhesion (8.3); absence ofembrittlement (8.4); reflectivity (8.5); and undercoats (S1.4),and4.1.7 Sampling plans (Section 7) and

17、 quality assurance(S1.2).5. Process Requirements5.1 Preparatory ProceduresThe basis metal shall be sub-jected to such cleaning procedures as are necessary to ensure asurface satisfactory for subsequent electroplating. Materialsused for cleaning shall have no damaging effects on the basismetal result

18、ing in pits, intergranular attack, stress corrosioncracking, or hydrogen embrittlement.NOTE 1For basis metal preparations, the following appropriateASTM standards are recommended: Practices B183, B242, B252, B254,B281, B322, B343, B481, and B482.5.2 Preplating Operations:5.2.1 Electroplating shall b

19、e applied after all basis metalheat treatments and mechanical operations such as forming,machining, and joining of the article have been completed.5.2.2 Stress Relief TreatmentAll steel parts having anultimate tensile strength of 1050 MPa (approximately 35 HRC)and above and that have been machined,

20、ground, cold formed,or cold straightened shall have heat treatment to 190 6 15Cfor a minimum of 5 h before cleaning and electroplating.5.3 Post-Plating Procedures:5.3.1 Embrittlement ReliefSteel parts having an ultimatetensile strength of 1200 MPa (approximately 38 HRC) orgreater shall be baked at 1

21、90 6 15C for a minimum of 8 hwithin 4 h after electroplating to provide hydrogen embrittle-ment relief. Steel parts having an ultimate tensile strengthgreater than 1300 MPa (approximately 40 HRC) shall be bakedat 190 6 15C for a minimum of 23 h within 4 h afterelectroplating.6. Coating Requirements6

22、.1 Nature of CoatingThe coating shall be essentiallypure rhodium produced by electrodeposition from aqueouselectrolytes.6.2 ThicknessThe rhodium coating thickness on all sig-nificant surfaces shall conform to the requirements of thespecified class as defined in Section 3.6.3 Significant SurfacesSign

23、ificant surfaces are defined asthose normally visible (directly or by reflection) or are essentialto the serviceability or function of the article or which can bethe source of corrosion products or tarnish films that interferewith the function or desirable appearance of the article. Whennecessary, t

24、he significant surfaces shall be indicated on thedrawings of the parts, or by the provision of suitably markedsamples.NOTE 2Variation in the coating thickness from point-to-point on acoated article is an inherent characteristic of electroplating processes.Therefore, the coating thickness will have t

25、o exceed the specified value atsome points on the significant surfaces to ensure that the thickness equalsor exceeds the specified value at all points. Therefore, the average coatingthickness on an article will usually be greater than the specified value; howmuch greater is largely determined by the

26、 shape of the article (see PracticeB507) and the characteristics of the electroplating process. Additionally,the average coating thickness on an article will vary from article to articlewithin a production lot. If all of the articles in a production lot are to meetthe thickness requirement, the aver

27、age coating thickness of the productionlot as a whole will be greater than the average necessary to ensure that asingle article meets the requirements.6.4 Appearance:6.4.1 Electroplated coatings shall completely cover all sur-faces as specified in the manufacturing document and shallhave a uniform a

28、ppearance to the extent that the nature of thebasis metal and good commercial practices permit.6.4.2 Defects in the surface of the basis metal such asscratches, pits, nonconducting inclusions, and roll and diemarks, may adversely affect the appearance and performanceof the applied coatings. Such def

29、ects that persist in the finishdespite the observance of good metal finishing practices shallnot be cause for rejection.NOTE 3Applied finishes generally perform better in service when thesubstrate over which they are applied is smooth and free from torn metal,inclusions, pores, and other defects. It

30、 is recommended that the specifi-cations covering the unfinished product provide limits for those defects. Ametal finisher often can remove defects through special treatments such asgrinding, polishing, abrasive blasting, chemical treatments, and elec-tropolishing. However, these are not normal in t

31、he treatment stepspreceding the application of the finish. When they are desired, they are thesubject of special agreement between the purchaser and the supplier.6.5 AdhesionThe rhodium coatings shall be free of blis-ters and peeled areas when tested in accordance with 8.3.7. Sampling7.1 A random sa

32、mple of the size required by Test MethodsB602 or B762 shall be selected from the inspection lot (see7.2). The articles in the lot shall be inspected for conformanceto the requirements of this specification and the lot shall beclassified as conforming or nonconforming to each requirementaccording to

33、the criteria of the sampling plans in Test MethodB602.NOTE 4Test Method B602 contains four sampling plans, three for usewith nondestructive test methods. The fourth is to be used with destructivetest methods. The three methods for nondestructive tests differ in thequality level they require of the p

34、roduct. Test Method B602 requires useof the plan with the intermediate quality level unless the purchaserspecifies otherwise. It is recommended that the purchaser compare theplans with his needs and state which plan is to be used. If the plans in TestMethod B602 do not serve the needs, additional on

35、es are given in GuideB634 88 (2009)2B697 which provides a large number of plans and also gives guidance inthe selection of a plan. When Guide B697 is specified, the buyer and sellerneed to agree on the plan to be used.NOTE 5Test Method B762 is a variables sampling plan. Such planscan only be used wh

36、en a test yields a measured quantity, such as thickness,and when the requirements are stated as a numerical limit also such asthickness. Test Method B762 contains several plans and gives instructionsfor calculating plans for special needs. Buyer and seller may agree on theplan or plans to be used; i

37、f not Test Method B762 identifies the plan to beused.NOTE 6When both destructive and nondestructive tests exist for themeasurement of a characteristic, the purchaser needs to state which is tobe used so that the proper sampling plan is selected. Whether or not a testis destructive may not always be

38、clear. A test may destroy the coating butin a noncritical area. The purchaser needs to state whether the test is to beconsidered destructive or nondestructive. The decision is importantbecause the plans for destructive tests are significantly less able todiscriminate between acceptable and unaccepta

39、ble lots. This is becausefewer parts are tested.7.2 An inspection lot shall be defined as a collection ofcoated articles that are of the same kind, that have beenproduced to the same specifications, that have been coated bya single supplier at one time or at approximately the same timeunder essentia

40、lly identical conditions, and that are submittedfor acceptance or rejection as a group.7.3 If special test specimens are used to represent the coatedarticles in a test, the specimens shall be of the nature, size, andnumber, and shall be processed as required in accordance with8.1.8. Test Methods8.1

41、Special Test Specimens:8.1.1 Special test specimens are used to represent the coatedarticles in a test if the articles are of a size, shape, or materialthat is not suitable for the test, or if it is preferred not to submitarticles to a destructive test because, for example, the articlesare expensive

42、 or few in number. The permission or therequirement to use special test specimens, their number, thematerial from which they are to be made, and their shape andsize shall be stated by the purchaser.8.1.2 The special test specimen shall duplicate those char-acteristics of the article that influence t

43、he property being tested,and it shall be processed with the article through those processsteps that influence the property.8.1.2.1 The special test specimens used to represent anarticle in an adhesion, corrosion resistance, or appearance testshall be made of the same material, shall be in the sameme

44、tallurgical condition, and shall have the same surfacecondition as the articles they represent; they shall be placed inthe production lot of and be processed along with the articlesthey represent.8.1.2.2 Special test specimens used to represent an article ina coating thickness test shall be introduc

45、ed into the process atthe point where the coating or coatings are applied and shall becarried through all steps that have a bearing on the coatingthickness.NOTE 7When special test specimens are used to represent a coatedarticle in a thickness test, the specimens will not necessarily have the samethi

46、ckness and thickness distribution as the article unless the specimens andthe article are of the same general size and shape. Therefore, before coatedarticles may be accepted on the basis of a thickness test performed on testspecimens, the relationship between the thickness on special test speci-mens

47、 and the thickness on the part needs to be established. The criterionof acceptance is that thickness on the specimen that corresponds to therequired thickness on the article.8.2 Thickness:8.2.1 The coating thickness shall be measured at locationson the significant surfaces where it would be expected

48、 to be aminimum.8.2.2 Use Test Method B567 for beta backscatter or TestMethod B568 for X-ray fluorescence (as applicable) fornondestructive methods.8.2.3 Rhodium thickness can be measured destructively byMethod B487 for microscopical cross sectioning. This methodshall not be used for thicknesses les

49、s than 2.5 m.8.3 AdhesionDetermine adhesion in accordance with oneof the procedures given in Practice B571, Bend Tests and HeatQuench Test.8.4 Hydrogen Embrittlement Relief:8.4.1 Steel products that are required by 5.3 to be heattreated to remove hydrogen embrittlement shall be subjectedfor 200 6 8 h to a sustained tensile load equal to 75 6 2%ofthe ultimate tensile notch strength of the material. If theproduct fractures during the test or is found, when examinedafter the test, to have cracks, it does not conform to therequirement for hydrogen embrittlement reli

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1