ASTM B687-1999(2005)e1 Standard Specification for Brass Copper and Chromium-Plated Pipe Nipples《镀黄铜、镀铜和镀铬管接头标准规范》.pdf

1、Designation: B 687 99 (Reapproved 2005)e1Standard Specification forBrass, Copper, and Chromium-Plated Pipe Nipples1This standard is issued under the fixed designation B 687; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.e1NOTEEditorial corrections were made through

3、out in March 2005.1. Scope*1.1 This specification establishes the requirements for brassand copper pipe nipples in standard pipe sizes from18 to 8 in.,inclusive, in standard lengths, and chromium-plated pipenipples in standard pipe sizes from18 to 2 in., inclusive, instandard lengths.1.1.1 Chromium-

4、plated pipe nipples ordered under thisspecification are intended for interior use in decorative appli-cations.1.2 The values stated in inch-pound units are the standard.The values given in parentheses are for information only.1.3 This standard does not purport to address all of thesafety concerns, i

5、f any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B42 Specification for Seamless Copper Pipe, St

6、andardSizesB43 Specification for Seamless Red Brass Pipe, StandardSizesB 456 Specification for Electrodeposited Coatings of Cop-per Plus Nickel Plus Chromium and Nickel Plus Chro-miumB 846 Terminology for Copper and Copper AlloysE29 Practice for Using Significant Digits in Test Data toDetermine Conf

7、ormance with Specifications2.2 ANSI/ASME Standard:B1.20.1 Pipe Threads, General Purpose (Inch)32.3 Military Standard:MIL-STD-105 Sampling Procedures and Tables for Inspec-tion by Attributes43. Terminology3.1 Definitions:3.1.1 For definitions of terms relating to copper and copperalloys, refer to Ter

8、minology B 8464. Ordering Information4.1 Contracts and purchase orders for product under thisspecification are to contain the following information:4.1.1 ASTM specification designation and year of issue,4.1.2 Type of material (Section 5),4.1.3 Weight of material; regular or extra strong,4.1.4 Diamet

9、er; nominal or actual outside diameter,4.1.5 Length; standard or special (8.2 and Table 2), and4.1.6 Quantity; number of pieces or total weight of eachmaterial and size.4.2 The following options are available under this specifi-cation and are to be specified in the contract or purchase orderwhen req

10、uired:4.2.1 Chromium plated finish,4.2.2 Short Plumbing (hospital) threads,4.2.3 Certification (Section 16), and4.2.4 Test and Inspection Reports, if required (Section 17).4.3 In addition, when material is purchased for agencies ofthe U.S. government, it shall conform to the supplementaryrequirement

11、s as defined herein when specified in the contractor purchase order.5. Materials and Manufacture5.1 Copper pipe nipples shall be produced from regular orextra strong pipe conforming to the requirements of Specifi-cation B42.5.2 Brass pipe nipples shall be produced from regular orextra strong pipe co

12、nforming to the requirements of Specifi-cation B43.1This specification is under the jurisdiction ofASTM Committee B05 on Copperand Copper Alloys and is the direct responsibility of Subcommittee B05.04 on Pipeand Tube.Current edition approved Mar. 1, 2005. Published March 2005. Originallyapproved in

13、1981. Last previous edition approved in 1999 as B 687 99.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Ava

14、ilable from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.4Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, ATTN: NPODS.1*A Summary of Changes section appears at the end of this standard

15、.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.3 Chromium-plated pipe nipples shall be produced fromregular weight brass pipe conforming to the requirements ofSpecification B43.6. Chemical Composition6.1 The chemical composition s

16、hall conform to the require-ments of the specification under which the pipe was ordered.7. Temper7.1 The product temper and its properties and characteristicsshall conform to the requirements of the specification underwhich the pipe was ordered.8. Dimensions, Mass and Permissible Variations8.1 Lengt

17、hs:8.1.1 The standard lengths and sizes of nipples generallyavailable are shown in Table 2. The availability of such nipplesindicated by pipe size are shown in Table 3.8.1.2 Special lengths and sizes of nipples are permitted to bespecified when required. Standard and special lengths shallconform to

18、the tolerance requirements of 8.1.3.8.1.3 TolerancesNipples with lengths up through 12 in.(305 mm) long shall have a length tolerance of 6116 in. (1.6mm). Nipples over 12 in. long shall have a tolerance of 618 in.(3.2 mm).8.2 Threads:8.2.1 Pipe nipples shall be threaded on both ends with NPTTaper Pi

19、pe Threads conforming to the requirements of ANSIB1.20.1, except for close nipples where L4 and V are shorter,due to fewer imperfect threads. It is standard manufacturingpractice on all other nipple lengths to vary the L4 6 twothreads. All other dimensions, tolerances, and gaging practicesremain the

20、 same as ANSI B1.20.1, and the Annex.8.2.1.1 Threads shall be right hand on both ends, exceptwhen otherwise specified.8.2.2 Threads, Chromium-Plated NipplesThreads onchromium-plated nipples shall be gaged after plating. Threadson18 to 1-in. standard pipe size nipples shall be NPT TaperPipe Threads,

21、in accordance with 8.2.1. Threads on 114 to 2-in.standard pipe size nipples shall be short plumbing (hospital)threads, in accordance with Table 1.On18 to 1-in. standardpipe size nipples, short plumbing (hospital) threads, if speci-fied, shall be in accordance with Table 1.9. Workmanship, Finish and

22、Appearance9.1 End FinishThe ends of the pipe nipples shall bechamfered on the outside at an angle of 35 6 10 to the centralaxis. (It is standard practice that the18-in. nominal size nipplesneed not be chamfered.) Ends shall be cut reasonably square tothe central axis. All burrs on the outside shall

23、be removed.9.2 Chromium PlatingChromium plate on brass nipplesshall meet the requirements of service condition SC I ofSpecification B 456, except the equivalent nickel thicknessshall be 0.003 mm.10. Sampling10.1 Arandom sample of pipe nipples shall be selected fromone production lot in accordance wi

24、th MIL-STD-105 at In-spection Level II. In terms of defects per 100 units, theAcceptable Quality Level (AQL) shall be 1.5.10.1.1 Production LotA production lot shall be as deter-mined by the manufacturer, provided that all of the pipe usedin a single production lot shall comply with the provisions o

25、fSection 5 and all of the nipples shall be of the same size,length, type, weight, finish, and thread form.11. Number of Tests and Retests11.1 Allowances for resampling and retesting shall be inaccordance with the Inspection Level and Acceptable QualityLevels detailed in 10.1.12. Significance of Nume

26、rical Limits12.1 For the purpose of determining compliance with thespecified limits for the requirements listed in the followingtable, an observed value shall be rounded as indicated inaccordance with the rounding method of Practice E29:PropertyRounded Unit forObserved or Calculated ValueLinear Dime

27、nsionsTolerancesnearest unit in the last right-hand significantdigit used in expressing the limiting value13. Inspection13.1 Each sample nipple shall be examined visually toverify conformance with each of the following requirements:13.1.1 The material is the type and weight of materialspecified,13.1

28、.2 The finish is as specified, if chromium-plated,13.1.3 The ends are reasonably square to the central axisand all burrs have been removed, and13.1.4 Threads are not burred or damaged.13.2 Each sample nipple shall be inspected to verify con-formance with each of the following requirements:13.2.1 Pip

29、e size,13.2.2 Length,13.2.3 Thread dimensions, and13.2.4 Chamfer.13.3 Chromium PlatingUnless otherwise specificallyagreed upon between the manufacturer and the purchaser, theindividual samples need not be individually inspected as toTABLE 1 Short Plumbing (Hospital) ThreadsA,BNOTEShort plumbing (hos

30、pital) threads are normally used only onchromium-plated nipples. The purpose of such threads is that a minimumof thread shall remain exposed after the nipple is screwed into a fitting.NominalPipe Size,NPSOutsideDiameterof Pipe, DThreadsper in.,NOverall ExternalThread Length, L4Inches Threads18 0.405

31、 27 0.26 714 0.540 18 0.33 638 0.675 18 0.33 612 0.840 14 0.43 634 1.050 14 0.43 61 1.315 1112 0.52 6114 1.660 1112 0.52 6112 1.900 1112 0.52 62 2.375 1112 0.52 6AAll dimensions, except threads per inch, in inches.BThis table represents a modification of Table 2 of ANSI B1.20.1; L4is modifiedas show

32、n. E2, L2, and V are modified accordingly. The threads shall meet thegaging requirements of Sections 6 and 11 of this specification.B 687 99 (2005)e12their chromium plating. It shall be sufficient for the manufac-turer to certify that (a) random nipples from the chromiumplating process have been tes

33、ted for conformance with Speci-fication B 456 (which records shall be retained by the manu-facturer) and do in fact conform and (b) there has been nosignificant change in the chromium plating process since thetests were last run.13.3.1 If inspection of the individual nipples is agreed upon,then it s

34、hall be conducted by any method allowed by Specifi-cation B 456.13.4 PipeThe pipe from which each production lot ismanufactured shall be of the same size, type, and weight andshall be tested in accordance with the applicable ASTM pipespecification. At the option of the manufacturer, the pipe maybe t

35、ested by the manufacturer, by the pipe mill that producedthe pipe, or by an independent laboratory.13.5 Source InspectionIf required, source inspection ofthe product by the purchaser shall be established by agreementbetween the manufacturer or supplier and purchaser at the timeof placing the order.

36、In such cases, the nature of the facilitiesnecessary for the inspector to determine that the product is inconformance to this specification shall be included in theagreement. The inspection shall be conducted so as not tounnecessarily interfere with normal operations.14. Rejection and Rehearing14.1

37、Rejection:14.1.1 Product that fails to conform to the requirements ofthis specification when inspected by the purchaser or purchas-ers agent, shall be subject to rejection.14.1.2 Rejection shall be reported to the manufacturer orsupplier promptly and in writing.14.1.3 In case of dissatisfaction with

38、 the results upon whichrejection is based, the manufacturer or supplier is permitted tomake claim for a rehearing.14.2 Rehearing:14.2.1 As a result of product rejection, the manufacturer orsupplier is permitted to make claim for a retest to be conductedby the manufacturer or supplier and the purchas

39、er. Samples ofthe rejected product shall be taken in accordance with thisproduct specification, and subjected to test by both partiesusing the test methods specified in the product specification, or,alternatively, upon agreement of both parties, an independentlaboratory shall be selected.15. Certifi

40、cation15.1 When specified in the contract or purchase order, thepurchaser shall be furnished certification that samples repre-senting each lot have been tested or inspected as directed in thisspecification and the requirements have been met.16. Test and Inspection Reports16.1 When specified in the c

41、ontract or purchase order, areport of test and inspection results shall be furnished.17. Packaging and Package Marking17.1 Individual nipples are not normally identified. Nipplespackaged shall have their containers legibly marked to showbrand or name of manufacturer, quantity, size, length, type ofm

42、aterial, weight of material (if other than regular), and finish(if chromium-plated).17.1.1 At the manufacturers option, large size, extra longnipples and odd lots are bagged or bundled with tags identi-fying the product as specified in 15.1.TABLE 2 Pipe Nipples by Length and Pipe SizeType of Nipple1

43、814381234 1114 112 2212 3312 4568Pipe Nipple Lengths, in.A,BClose (cl)3478 1118 138 112 158 134 2212 258 234 278 3318 312112 112 112 112 . . . . . . . . . . . .22222222. . . . . . .212 212 212 212 212 212 212 212 212 . . . . . . .33333333333. . . .312 312 312 312 312 312 312 312 312 312 312 . . . .

44、.4444444444444. .412 412 412 412 412 412 412 412 412 412 412 412 412 412 412 .5555555555555555512 512 512 512 512 512 512 512 512 512 512 512 512 512 512 512666666666666666677777777777777778888888888888888999999999999999910 10 10 10 10 10 10 10 10 10 10 10 10 10 10 1011 11 11 11 11 11 11 11 11 11 11

45、 11 11 11 11 1112 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12Rightandleft. . 4444444. . . . .ANipples shorter than close nipples are not recommended for pressure application.B1 in. = 25.4 mm.TABLE 3 Pipe Nipple Sizes According to MaterialWeightNominal Pipe Sizes, in.18 to 2in., incl214 to 4in., inc

46、l5 and 6in.8in.Regular weight brass XXXXExtrastrongbrasRegular copper XXXXExtra strong copper X X . . . . . .Chromium-plated regular brass X . . . . . . . . .B 687 99 (2005)e1317.2 Chromium-Plated NipplesExcept for close nipples,chromium-plated nipples shall be individually packaged,wrapped, or othe

47、rwise protected to ensure against nicking orother cosmetic damage in transit.17.3 Nipples shall be packaged and prepared for shipmentin such a manner as to ensure acceptance by common carrierfor transportation at the lowest rate applicable and to affordprotection from the normal hazards of transport

48、ation.18. Keywords18.1 close nipple; pipe nipple; short plumbing (hospital)threadsSUPPLEMENTARY REQUIREMENTSThe following supplementary requirements shall apply only when specified by the purchaser in theinquiry, contract, or order for agencies of the U.S. government.S1. Part Numbering SystemS1.1 Th

49、is supplement provides a part numbering system forthe identification of standard items for government use ofSpecification B 687.NOTE The government encourages the general use of this partnumbering system to achieve maximum parts standardization.S1.2 The part number consists of the document identifierfollowed by the code for the weight of material (regular orextra strong), a dash, dash number (Table S1.1), material code,and, if applicable, finish code (see example).Exampl