ASTM B908-2009 Standard Practice for the Use of Color Codes for Zinc Casting Alloy Ingot《锌合金铸锭的色码的使用的标准实施规程》.pdf

1、Designation: B908 09Standard Practice for theUse of Color Codes for Zinc Casting Alloy Ingot1This standard is issued under the fixed designation B908; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A num

2、ber in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This standard is published with the following objectives:1.2 To establish standard color codes for the Zinc DieCasting and Foundry indust

3、ry, and1.3 To standardize the use and application of these colorcodes.1.4 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the ap

4、propriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on

5、 dateof order acceptance form a part of this specification to theextent referenced herein:2.2 ASTM Standards:2B240 Specification for Zinc and Zinc-Aluminum (ZA) Al-loys in Ingot Form for Foundry and Die CastingsB275 Practice for Codification of Certain Nonferrous Met-als and Alloys, Cast and Wrought

6、B327 Specification for Master Alloys Used in Making ZincDie Casting AlloysB792 Specification for Zinc Alloys in Ingot Form for SlushCastingB793 Specification for Zinc Casting Alloy Ingot for SheetMetal Forming Dies and Plastic Injection MoldsB892 Specification for ACuZinc5 (Zinc-Copper-Aluminum) All

7、oy in Ingot Form for Die CastingsB899 Terminology Relating to Non-ferrous Metals andAlloysE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.3 ISO Standard:ISO 301 Zinc alloy ingots intended for casting, 1981-05-1532.4 CEN Standard:EN 1774 Zinc and zinc alloysAlloys

8、for foundrypurposesIngot and liquid, September 199743. Terminology3.1 Terms shall be defined in accordance with TerminologyB899.4. Significance and Use4.1 The purpose of these color codes is to allow for quickidentification of ingot bundles or jumbo ingots of zinc castingalloys. Other than jumbo ing

9、ots, this standard is not intended toimply that each ingot will be color-coded but only that eachingot bundle be color coded.4.2 Each ingot bundle or jumbo ingot shall be identifiedwith the appropriate color code listed in Table 1.4.3 The color will be applied as a stripe, or stripes, on twoadjacent

10、 sides of the ingot bundle or jumbo ingot. The colorstripes will be applied to include the ingot bundle foot.4.4 When using multiple stripes, the colored stripes will beapplied from left to right as indicated in Table 1.4.5 In the absence of a written agreement to the contrarybetween the supplier an

11、d end user, the North American colorcode will be the standard for all North American transactions;for all other transactions the International Color Code will beused.5. Keywords5.1 ACuZinc; ACuZinc5; color; color code; Kirksite; Kirk-site A; Kirksite B; non-ferrous metals; Zamak; Zamak 2;Zamak 3; Za

12、mak 5; Zamak 7; zinc; zinc alloys; zinc-aluminumalloys; zinc-copper-aluminum alloys1This practice is under the jurisdiction of ASTM Committee B02 on NonferrousMetals and Alloys and Alloys and is the direct responsibility of SubcommitteeB02.04 on Zinc and Cadmium.Current edition approved Oct. 1, 2009

13、. Published October 2009. Originallyapproved in 2000. Last previous edition approved in 2008 as B908 - 03 (2008).DOI: 10.1520/B0908-09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume inf

14、ormation, refer to the standards Document Summary page onthe ASTM website.3“English Version” available from American National Standards Institute(ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http:/www.ansi.org.4“English Version” available from Global Engineering Documents, 15 InvernessWay,

15、East Englewood, CO 80112-5704, http:/.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.SUMMARY OF CHANGESCommittee B02 has identified the location of selected changes t

16、o this standard since the last issue(B908 - 03 (2008) that may impact the use of this standard. (Approved October 1, 2009.)(1) Added color code for V125 to Table 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this

17、standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be r

18、eviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of therespon

19、sible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West

20、 Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Color Cod

21、esCommon UNSAASTMStandardASTMAlloyTraditionalColor CodeNorth AmericaBInternationalAlloy 3 Z33521 B240 AG 40ACZamak 3 None White/YellowDAlloy 7 Z33522 B240 AG 40BCZamak 7 Brown White/BrownEAlloy 5 Z35530 B240 AC 41ACZamak 5 Black White/BlackDAlloy 2 Z35540 B240 AC 43ACZamak 2 Green White/GreenDZA-8 Z

22、35635 B240 ZA-8 ZA-8 Blue White/BlueDZA-12 Z35630 B240 ZA-12 ZA-12 Orange White/OrangeDZA-27 Z35840 B240 ZA-27 ZA-27 Purple White/PurpleDACuZinc 5 Z46540 B892 Zn-Cu5-AI3 ACuZinc5FRed White/RedEV12 Z33730 B327 V12 V12 Pink White/PinkEV12-5 B327 V12-5 V12-5 Pink/Black White/Pink/BlackSlush Casting All

23、oy A Z34510 B792 Slush Casting Alloy A Slush Casting Alloy A Black/Red White/Black/RedESlush Casting Alloy B Z30500 B792 Slush Casting Alloy B Slush Casting Alloy B Black/Orange White/Black/OrangeEZinc Casting Alloy for Dies and Molds - A Z35543 B793 Die & Mold Alloy A Kirksite A Green/Red White/Gre

24、en/RedEZinc Casting Alloy for Dies and Molds - B Z35542 B793 Die & Mold Alloy B Kirksite B Green/Black White/Green/BlackEAUNS assignations were established in accordance with Practice E527. The last digit of a UNS number differentiates between alloys of similar composition.BThe North American system

25、 is design to be a simplified version of the International system by eliminating the leading white stripe and in the case of Alloy 3 eliminatingall stripes.CASTM alloy designations established in accordance with Practice B275.DThe color codes for these alloys are adapted from European standard (CEN)

26、 specification EN 1774. No color coding currently exists in International standard ISO 301.EThese alloys are not currently included in European standard EN 1774 nor International standard ISO 301 and no color codes have previously been assigned.FACuZinc and ACuZinc5 are registered names of the General Motors Corporation.B908 092