ASTM B914-2003e2 Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel《钢的热浸镀锌中使用的锌及锌合金锭色码的标准规程》.pdf

1、Designation: B 914 03e2Standard Practice forColor Codes on Zinc and Zinc Alloy Ingot for Use in Hot-DipGalvanizing of Steel1This standard is issued under the fixed designation B 914; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,

2、the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTEUNS Z31510 was added editorially to Table 1 in November 2003.e2NOTEScope section was corrected editorially in A

3、pril 2005.1. Scope*1.1 This standard is published with the following objectives:1.1.1 To establish standard color codes for zinc, zinc alloyand zinc master alloy ingot used by the Hot-Dip Galvanizingindustry, and1.1.2 To standardize the use and application of these colorcodes.1.2 This standard does

4、not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufa

5、cturer, to establish appropriatesafety and health practices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on dateof order acceptance form a part of this specification to theextent referenced herein:2.2

6、 ASTM Standards:2B6 Standard Specification for ZincB 275 Practice for Codification of Certain Nonferrous Met-als and Alloys, Cast and WroughtB 750 Standard Specification for Zinc-5 % Aluminum-Mischmetal Alloy in Ingot Form for Hot-Dip CoatingsB 852 Standard Specification for Continuous GalvanizingGr

7、ade (CGG) Zinc Alloys for Hot-Dip Galvanizing ofSheet SteelB 860 Standard Specification for Zinc Master Alloys forUse in Hot Dip GalvanizingB 899 Terminology Relating to Non-ferrous Metals andAlloysE 527 Practice for Numbering Metals and Alloys (UNS)2.3 ISO Standard:ISO 752, Zinc and Zinc AlloysPrim

8、ary Zinc2.4 CEN Standard:EN 1179, Zinc and Zinc AlloysPrimary Zinc3. Terminology3.1 Terms shall be defined in accordance with TerminologyB 899.4. Significance and Use4.1 The purpose of these color codes is to allow for quickidentification of ingot bundles or jumbo ingots of alloys usedfor hot-dip ga

9、lvanizing. Other than jumbo ingots, this standardis not intended to imply that each ingot will be color-coded butonly that each ingot bundle be color coded.4.2 Each ingot bundle or jumbo ingot shall be identifiedwith the appropriate color code listed in Table 1.4.3 The color will be applied as a str

10、ipe, or stripes, on twoadjacent sides of the ingot bundle or jumbo ingot. The colorstripes will be applied to include the ingot bundle foot.4.4 When using multiple stripes, the colored stripes will beapplied from left to right as indicated in Table 1.4.5 In the absence of a written agreement to the

11、contrarybetween the supplier and end user, the North American colorcode will be the standard for all North American transactions;for all other transactions the International Color Code will beused.5. Keywords5.1 aluminum-zinc alloys; color; color code; GALFAN;GALVALUME; galvanizing; hot-dip; non-fer

12、rous metals; zinc;zinc alloys; zinc-aluminum alloys1This practice is under the jurisdiction of ASTM Committee B02 on NonferrousMetals and Alloys and is the direct responsibility of Subcommittee B02.04 on Zincand Cadmium.Current edition approved June 10, 2003. Published August 2003. Originallyapprove

13、d in 2000. Last previous edition approved in 2000 as B 914 - 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM websi

14、te.1*A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.SUMMARY OF CHANGESCommittee B02 has identified the location of selected changes to this standard since the last issu

15、e (B 914 - 00)that may impact the use of this standard.(1) Corrected Primary Zinc Alloys to Primary Zinc Grades inTable 1.(2) Footnotes E and F added to Table 1.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this sta

16、ndard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be revi

17、ewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsib

18、le technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Co

19、nshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Color Codes

20、for Zinc and Zinc Alloys Used for Hot Dip GalvanizingAlloy UNSAASTMStandardNominal Composition Color CodeAl Other North AmericaBInternationalPrimary Zinc GradesCSHG (Z13001) B6 Yellow YellowHG (Z15001) B6 Green GreenPW (Z19001) B6 Pb1.0 % Black BlackCGG Alloys(Z80310) B 852 0.25 Brown/Brown Yellow/B

21、rown(Z80411) B 852 0.35 Blue/Blue Yellow/Blue(Z80511) B 852 0.45 Purple/Purple Yellow/Purple(Z80531) B 852 0.45 Pb0.02 % Red/Red Yellow/Red(Z80610) B 852 0.55 Pink/Pink Yellow/Pink(Z80710) B 852 0.65 Green/Green Yellow/Green(Z80810) B 852 0.75 Black/Black Yellow/Black(Z80910) B 852 1.00 Orange/Orang

22、e Yellow/OrangeMaster AlloysType A-1 (Z30750) B 860 10.0 High Purity Red/Green Yellow/Red/GreenType A-2 (Z31710) B 860 10.0 Low Purity Red/Black Yellow/Red/BlackType A-3 (Z30503) B 860 5.0 High Purity Red/Blue Yellow/Red/BlueType A-4 (Z31510) B 860 5.0 Low Purity Red/Yellow Yellow/Red/YellowType S-1

23、 (Z55710) B 860 Sb10.0 % Black/Green Yellow/Black/GreenSpecialty AlloysGALFAND(Z38510) B 750 5.0 Mischmetal Purple/Blue Yellow/Purple/BlueGALVALUMEE55.0 Si1.5 % Orange/Green Yellow/Orange/GreenAUNS assignations were established in accordance with Practice E 527. The last digit of a UNS number differ

24、entiates between alloys of similar composition.BThe North American system is designed to be a simplified version of the International system by eliminating the leading yellow stripe.CColor codes taken from European Standard EN 1179.DGALFAN is a registered trademark of the GALFAN Information Center, Inc.EGALVALUME is a registered trademark of BIEC International Inc., USA.B91403e22