ASTM B914-2013e1 Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel《钢的热浸镀锌中使用的锌及锌合金锭色码标准操作规程》.pdf

1、Designation: B914 131Standard Practice forColor Codes on Zinc and Zinc Alloy Ingot for Use in Hot-DipGalvanizing of Steel1This standard is issued under the fixed designation B914; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、 year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTESummary of Changes and keywords were added editorially in September 2013.1. Scope*1.1 This standard is published wit

3、h the following objectives:1.1.1 To establish standard color codes for zinc, zinc alloyand zinc master alloy ingot used by the Hot-Dip Galvanizingindustry, and1.1.2 To standardize the use and application of these colorcodes.1.2 This standard does not purport to address all of thesafety concerns, if

4、any, associated with its use. It is theresponsibility of the user of this standard to become familiarwith all hazards including those identified in the appropriateMaterial Safety Data Sheet (MSDS) for this product/materialas provided by the manufacturer, to establish appropriatesafety and health pra

5、ctices, and determine the applicability ofregulatory limitations prior to use.2. Referenced Documents2.1 The following documents of the issue in effect on dateof order acceptance form a part of this specification to theextent referenced herein:2.2 ASTM Standards:2B6 Specification for ZincB275 Practi

6、ce for Codification of Certain Nonferrous Metalsand Alloys, Cast and WroughtB750 Specification for GALFAN (Zinc-5 % Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip CoatingsB852 Specification for Continuous Galvanizing Grade(CGG) Zinc Alloys for Hot-Dip Galvanizing of SheetSteelB860 Specificatio

7、n for Zinc Master Alloys for Use in HotDip GalvanizingB899 Terminology Relating to Non-ferrous Metals and Al-loysE527 Practice for Numbering Metals and Alloys in theUnified Numbering System (UNS)2.3 ISO Standard:ISO 752 Zinc and Zinc AlloysPrimary Zinc32.4 CEN Standard:EN 1179 Zinc and Zinc AlloysPr

8、imary Zinc43. Terminology3.1 Terms shall be defined in accordance with TerminologyB899.4. Significance and Use4.1 The purpose of these color codes is to allow for quickidentification of ingot bundles or jumbo ingots of alloys usedfor hot-dip galvanizing. Other than jumbo ingots, this standardis not

9、intended to imply that each ingot will be color-coded butonly that each ingot bundle be color coded.4.2 Each ingot bundle or jumbo ingot shall be identifiedwith the appropriate color code listed in Table 1.4.3 The color will be applied as a stripe, or stripes, on twoadjacent sides of the ingot bundl

10、e or jumbo ingot. The colorstripes will be applied to include the ingot bundle foot.4.4 When using multiple stripes, the colored stripes will beapplied from left to right as indicated in Table 1.4.5 In the absence of a written agreement to the contrarybetween the supplier and end user, the North Ame

11、rican colorcode will be the standard for all North American transactions;for all other transactions the International Color Code will beused.1This practice is under the jurisdiction of ASTM Committee B02 on NonferrousMetals and Alloys and is the direct responsibility of Subcommittee B02.04 on Zincan

12、d Cadmium.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 2000. Last previous edition approved in 2008 as B914 03 (2008). DOI:10.1520/B0914-13E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org.

13、For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.4Available from Global Engineering Documents, 15 Inverne

14、ss Way, EastEnglewood, CO 80112-5704, http:/.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States15. Keywords5.1 Alloy A-1; Alloy A-2; Alloy A-3; Alloy A-4; Alloy A-5;AlloyA-

15、6; Alloy S-1; aluminum-zinc alloys; color; color code;GALFAN; GALVALUME; galvanizing; hot-dip; non-ferrousmetals; zinc; zinc alloys; zinc-aluminum alloysSUMMARY OF CHANGESCommittee B02 has identified the location of selected changes to this standard since the last issue(B914-03(2008) that may impact

16、 the use of this standard. (Approved May 1, 2013.)(1) UNS numbers for HG and PW grades have been changed. (2) Master Alloy Types A-5 and A-6 have been added.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standar

17、d. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed

18、 every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible t

19、echnical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Consho

20、hocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to ph

21、otocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Color Codes for Zinc and Zinc Alloys Used for Hot Dip GalvanizingAlloy UNSAASTMStandardNominal Composition Color CodeAl Other North AmericaBInternationalPrimary Zinc GradesCSHG (Z13001) B6 Yellow YellowH

22、G (Z14003) B6 Green GreenPW (Z18005) B6 Pb1.0 % Black BlackCGG Alloys(Z80310) B852 0.25 Brown/Brown Yellow/Brown(Z80411) B852 0.35 Blue/Blue Yellow/Blue(Z80511) B852 0.45 Purple/Purple Yellow/Purple(Z80531) B852 0.45 Pb0.02 % Red/Red Yellow/Red(Z80610) B852 0.55 Pink/Pink Yellow/Pink(Z80710) B852 0.

23、65 Green/Green Yellow/Green(Z80810) B852 0.75 Black/Black Yellow/Black(Z80910) B852 1.00 Orange/Orange Yellow/OrangeMaster AlloysType A-1 (Z30750) B860 10.0 High Purity Red/Green Yellow/Red/GreenType A-2 (Z31710) B860 10.0 Low Purity Red/Black Yellow/Red/BlackType A-3 (Z30503) B860 5.0 High Purity R

24、ed/Blue Yellow/Red/BlueType A-4 (Z31510) B860 5.0 Low Purity Red/Yellow Yellow/Red/YellowType A-5 (Z31520) B860 4.0 High Purity Red/Brown Yellow/Red/BrownType A-6 (Z30504) B860 4.0 Low Purity Red/Purple Yellow/Red/PurpleType S-1 (Z55710) B860 Sb10.0 % Black/Green Yellow/Black/GreenSpecialty AlloysGA

25、LFAND(Z38510) B750 5.0 Mischmetal Purple/Blue Yellow/Purple/BlueGALVALUMEE55.0 Si1.5 % Orange/Green Yellow/Orange/GreenAUNS assignations were established in accordance with Practice E527. The last digit of a UNS number differentiates between alloys of similar composition.BThe North American system i

26、s designed to be a simplified version of the International system by eliminating the leading yellow stripe.CColor codes taken from European Standard EN 1179.DGALFAN is a registered trademark of the GALFAN Information Center, Inc.EGALVALUME is a registered trademark of BIEC International Inc., USA.B914 1312