ASTM C1053-2000(2005) Standard Specification for Borosilicate Glass Pipe and Fittings for Drain Waste and Vent (DWV) Applications《排水沟、污水沟和排出口用的硼硅酸盐玻璃管和配件的标准规范》.pdf

1、Designation: C 1053 00 (Reapproved 2005)Standard Specification forBorosilicate Glass Pipe and Fittings for Drain, Waste, andVent (DWV) Applications1This standard is issued under the fixed designation C 1053; the number immediately following the designation indicates the year oforiginal adoption or,

2、in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1

3、 This specification covers chemically resistant, low ex-pansion, Type I, borosilicate glass, Class A (see SpecificationE 438), used to manufacture corrosion-resistant pipe and fit-tings for drain, waste, and vent service.1.2 The pipe and fittings covered by the specification areintended for chemical

4、 resistant service above and below gradeunder gravity flow or vacuum conditions.1.3 The pipe and fittings shall have beaded or plain ends.2. Referenced Documents2.1 ASTM Standards:2C 600 Method of Thermal Shock Test on Glass PipeC 623 Test Method for Youngs Modulus, Shear Modulus,and Poissons Ratio

5、for Glass and Glass-Ceramics byResonanceC 693 Test Method for Density of Glass by BuoyancyE 438 Specification for Glasses in Laboratory Apparatus3. Ordering Information3.1 The minimum ordering information for material underthis specification shall include the following information:3.1.1 ASTM designa

6、tion and date of issue,3.1.2 Manufacturers catalog number or parts identification,3.1.3 Quantity ordered,3.1.4 Special test or certification requirements,3.1.5 Special packaging or marking, if required, and3.1.6 Accessory items such as couplings, drains, adapters,and cutters.4. Materials and Manufac

7、ture4.1 The glass components shall represent good workman-ship as consistent with standard glass process capabilities.5. Chemical Requirements Chemical Requirements5.1 The chemical requirements shall be as described inSpecification E 438.6. Physical Requirements6.1 The physical requirements shall be

8、 as described inSpecification E 438.6.2 Refer also to Annex A1 for additional physical require-ments.7. Operating Temperatures7.1 Minimum Operating TemperatureThe minimum ratedoperating temperature for all sizes shall be 40F (40C)provided the material being conveyed is fluid.7.2 Maximum Operating Te

9、mperatureThe maximumrated continuous operating temperature shall be 212F(100C).7.3 Thermal Shock ResistanceThe maximum allowabletemperature differential for installed systems shall be in accor-dance with Table 1 for the various pipe sizes. Maximumtemperature differential refers to an almost instanta

10、neoustemperature change, such as low-pressure steam followeddirectly by a flush of ice cold water, or the reverse. Maximumtemperature differential pertains to either inside or outside pipesurfaces.7.3.1 Thermal shock resistance is not ordinarily tested. Ifthermal shock resistance may be questioned,

11、it shall be testedin accordance with Method C 600. If all pieces tested pass theallowable temperature differential, the lot shall be accepted. Ifone or more failures occur, a retest shall be made using asample size twice that of the first test. If any failures occur onthe retest, the entire shipment

12、 shall be retested.8. Pressure Rating8.1 DWV piping systems are designed for gravity flow only.8.2 All pipe sizes are suitable for vacuum service.9. Dimensions and Permissible Variations9.1 Beaded Flanges:9.1.1 Flange Face FlatnessMaximum permissible devia-tion from a flat plane across the face of a

13、 flange on all sizesshall be116 in. (1.6 mm).1This specification is under the jurisdiction of ASTM Committee C14 on Glassand GlassProducts and is the direct responsibility of Subcommittee C14.05 on Glass Pipe.Current edition approved Sept. 1th, 2005. Published October 2005. Originallyapproved in 198

14、5. Last previous edition approved in 2000 as C 1053 00.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyr

15、ight ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.9.1.2 Flange Face SquarenessFlange faces of both pipeand fittings shall be square to the pipe centerline within thelimits prescribed in Table 2.9.1.2.1 Squareness of straight pipe lengths sha

16、ll be mea-sured by placing the pipe on rollers, located approximately 2in. (51 mm) from each end, and butting one end against a flatplate perpendicular to the axis of the rollers. The pipe shall berotated and length variation read with a suitable mechanism,such as a dial indicator. The maximum readi

17、ng shall not exceedthat shown in Table 2 for the respective pipe size.9.1.2.2 Pipe fittings shall be measured for flange squarenessby a gage having flat plates constructed at the angle required bythat fitting. One flange shall be firmly placed on one plate, andany difference between the remaining fl

18、ange face and the othersurface plate shall be measured with Feller gages. Differencesshall not exceed the amount shown in Table 2 for the respectivefitting size.9.1.3 Flange Dimensions and SpecificationsBeadedflange dimensions shall be as required by the manufacturer forthe system.9.2 Bow:9.2.1 Bow

19、for All Pipe DiametersBow shall be measuredby supporting the pipe in “V” blocks approximately 2 in. fromeach end with a dial gage at midlength, rotating the pipe full360. The total dial deflection divided by two is the measure ofbow, which shall not exceed 0.25 % of the pipe length.9.3 Dimensions of

20、 All Pipe and Fittings:9.3.1 Dimensional specifications for pipe and common fit-tings shall be as shown in the manufacturers literature. Typicalconfigurations are as illustrated in Figs. 1-45.10. Inspection10.1 Inspection of the material shall be made at the point ofdelivery unless otherwise agreed

21、upon by the purchaser and theseller.11. Packaging11.1 Pipe, fittings, and hardware shall be so packaged as toprevent damage during transportation and handling. Thoseitems packed in containers conforming to all constructionrequirements of consolidated freight classification as to burst-ing tests, siz

22、e limit, and gross mass shall be considered as beingproperly packed.11.2 All hardware items shall be packed in such a way as toprevent contact with glass components. Some typical hardwareitems are shown in Appendix X1.12. Keywords12.1 borosilicate; components; fittings; glass; pipeTABLE 1 Maximum Te

23、mperature Differential for Thermal ShockPipe Size, in. (mm)Sudden TemperatureDifference, Max F (C)112 3 (3876) 200 (93)4 (102) 175 (78)6 (152) 160 (71)TABLE 2 Flange Face SquarenessNominal Pipe Size, in.SquarenessMeasurement,Max, in.112 to 2132336441166564Size, in.A (OD) B (OD)Wall Thick-ness,in.Len

24、gth, ftADiameter, in. Diameter, in.112 2.06 1.84 0.17 5 and 102 2.58 2.34 0.17 5 and 103 3.69 3.41 0.20 5 and 104 4.84 4.53 0.27 5 and 106 7.12 6.66 0.33 5 and 10ALength includes coupling allowance.Nominal OD Over EPSA112 in. 213162in. 35163in. 54in. 6146in. 8916APipe with EPS (expanded polystyrene)

25、 covering for underground service;lengths of 5 ft only.FIG. 1 Standard Specifications for Straight Lengths of PipeA DimensionA,in.Size 90 60 45 2212 112 3212 22314 234 214 21435 312 234 23447 412 314 3146 7 ADimensions to beaded flanges include coupling allowance.FIG. 2 ElbowsC 1053 00 (2005)2FIG. 3

26、 ElbowA DimensionsA,in.Size 90 60 45 2212 112 412 412 412 41225 5 5 53612 612 612 61249 9 9 9612 12 12 12ADimensions to beaded flanges include coupling allowance.FIG. 4 Sweep ElbowsDimensionsA,in.Size A B2by112 43123by112 543by2 5 4124by112 74124by2 7 54by3 7 5126by112 95126by2 9 66by3 9 6126by4 9 8

27、ADimensions to beaded flanges include coupling allowance.FIG. 5 Quarter Bend ReducerDimensionsA,in.Size A B (min)2by112 41343by112 52143by2 5 2144by112 734by2 7 34by3 7 36by112 946by2 9 46by3 9 46by4 9 4ADimensions to beaded flanges include coupling allowance.FIG. 6 Straight Reducers and Eccentric R

28、educersDimensionsA,in.Size A B C112 by 112 6332by112 8314 42by2 8 4 43by112 12 412 63by2 12 412 63by3 12 6 64by112 14 5 74by2 14 5 74by3 14 612 74by4 14 8 76by3 20 734 106by4 20 9 106 by 6 20 10 10ADimensions to beaded flanges include coupling allowance.FIG. 7 Straight TC 1053 00 (2005)3FIG. 8 Test

29、T with Clean-OutDimensionsA,in.Size A B C112 by 112 6312 3342by112 8334 52by2 8 412 53by112 12 414 77163by2 12 5 77163by3 12 638 77164by112 14 474 8344by2 14 554 8344by3 14 7 8344by4 14 814 8346by2 20 634 12386by3 20 8 12386by4 20 9516 12386 by 6 20 12 1238ADimensions to beaded flanges include coupl

30、ing allowance.FIG. 9 Sanitary TFIG. 10 Adjustable Sanitary TC 1053 00 (2005)4FIG. 11 Adjustable Sanitary T (Plain End Outlet)FIG. 12 Compact Single Sanitary TDimensionsA,in.Size A B112 32182by2by112 314 2142312 21435124612 5346812 7ADimensions to beaded flanges include coupling allowance.FIG. 13 Dou

31、ble Quarter BendC 1053 00 (2005)5FIG. 14 Double Quarter Bend (Plain End Outlet)DimensionsA,in.Size A B112 452412 5123512 6124612 712ADimensions to beaded flanges include coupling allowance.FIG. 15 U BendDimensionsA,in.Size A112 121311841146112ADimensions to beaded flanges include coupling allowance.

32、FIG. 16 Cleanout PlugC 1053 00 (2005)6DimensionsA,in.Size A B C112 by 112 6178 4122by112 8212 4342by2 8 212 63by112 12 334 5123by2 12 334 6343by3 12 334 84by112 14 412 6384by2 14 412 7124by3 14 412 8344by4 14 412 106by2 20 534 96by3 20 534 10386by4 20 534 11126by6 20 534 14ADimensions to beaded flan

33、ges include coupling allowance.FIG. 17 Drainline YFIG. 18 Compact Single Drainline YC 1053 00 (2005)7DimensionsA,in.Size A B C D112 by 112 6412 458 1782by112 8434 512 2122by2 8 6 614 2123by112 12 538 714 3343by2 12 612 83343by3 12 812 93344by112 14 6 812 4124by2 14 7 914 4124by3 14 9 1014 4124by4 14

34、 11 11 4126by2 20 814 1158 5346 by 3 20 10 1212 5346 by 4 20 12 1312 5346 by 6 20 15 1412 534ADimensions to beaded flanges include coupling allowance.FIG. 19 Combination Y and18 BendFIG. 20 Compact Combination Y and18 BendFIG. 21 Compact Double Combination Y and18 BendC 1053 00 (2005)8FIG. 22 Runnin

35、g TrapFIG. 23 Swivel TrapP Style, Long OutletFIG. 24 Swivel TrapP Style, Short OutletFIG. 25 Swivel TrapS StyleC 1053 00 (2005)9FIG. 26 Running Trap (Vented)FIG. 27 Swivel TrapP Style (Plain End Outlet)FIG. 28 TrapP Style (Vented)Dimensions, in.Size Inletby OutletAB CD112 by 112 781 52by112 712 8112

36、 52by2 8316 834 112 5123by3 1014 1012 26124by4 1214 1212 212 7126by6 1812 31 338 24FIG. 29 TrapP StyleNOTE 1J Bend can be used in combination with quarter bend andreturn bend to make a variety of custom swivel traps.Dimensions, in.Size A B C112 by 112 71316 53122by112 81116 54122by2 878 512 418FIG.

37、30 J BendC 1053 00 (2005)10FIG. 31 Swivel Drum TrapS StyleFIG. 32 Partition TrapC 1053 00 (2005)11FIG. 33 Interceptor TrapFIG. 34 Drum TrapFIG. 35 Standard CleanoutC 1053 00 (2005)12FIG. 36 Cup SinksFIG. 37 Beaded Outlet 3- by 6-in. OvalFIG. 38 Beaded Outlet 3- by 9-in. OvalFIG. 39 Plain End Outlet

38、3- by 6-in. OvalFIG. 40 Plain End Outlet 6-in. HemisphericalFIG. 41 Plain End Outlet 3- by 9-in. OvalFIG. 42 Beaded Outlet 3-in. HemisphericalC 1053 00 (2005)13ANNEX(Mandatory Information)A1. GENERAL REFERENCE DATA FOR LOW-EXPANSION BOROSILICATE GLASSA1.1 Density2.24 g/cm3, measured at room temperat

39、ureby Test Method C 693.A1.2 Thermal Conductivity0.73 Btuft/hft2F (0.0035calcm/scm2C), measured at room temperature.A1.3 Specific Heat0.20 Btu/lbF (0.20 cal/gC), mea-sured at 75C.A1.4 Youngs Modulus9 000 000 to 10 000 000 psi (62 to69 GPa) when measured at room temperature in accordancewith Test Met

40、hod C 623.A1.5 Tensile StrengthBecause of effect of surface condi-tions on ultimate strength, nominal design shall be 1000 psi(6.9 MPa).FIG. 43 Bead Outlet 6-in. HemisphericalFIG. 44 3- by 6-in. Oval Horizontal Wall-Mounted Cup Sink 112-in.Plain End OutletFIG. 45 3- by 6-in. Oval Vertical 112-in. Ou

41、tlet Wall-Mounted CupSinkC 1053 00 (2005)14APPENDIX(Nonmandatory Information)X1. TYPICAL HARDWARENOTE 1Assembly consists of the following sink strainer fluorocarbonplastic 112-in. or 2-in. sink outlet fluorocarbon plastic; rubber gasket; andlocknut.Dimensions, in.Size A B C D112 33814 234 223151614

42、3258381458FIG. X1.1 Sink Outlet AssemblyNOTE 1Sink overflow is made of fluorocarbon plastic. Beehive typecan be modified to open type by cutting off top beehive section.Dimensions, in.Sink OutletSizeSize112 112 by 4112 112 by 6112 112 by 8FIG. X1.2 Sink OverflowC 1053 00 (2005)15NOTE 1Tailpiece is a

43、vailable in 612- and 1012-in. lengths. Specifylength when ordering. Glass can be field cut to exact length. Assemblyconsists of a plastic nut and a tailpiece.NOTE 2This assembly can be used on other 112-in. plastic or metalsink outlets having straight pipe threads.FIG. X1.3 112-in. Tailpiece Assembl

44、yNOTE 1Split coupling of 112 in. is used to join 112-in. beaded glasspipe to threaded 112-in. I.P.S. pipe.NOTE 2The assembly consists of a split coupling nut and a stainlesssteel clamp.FIG. X1.4 112-in. Split Coupling (Threaded to Beaded Pipe)Dimensions, in.Size O.D. Range A2by134 1.701.782by112 1.4

45、81.532by178 1.821.90NOTE 1Adapter assembly is used to join glass DWV pipe or fittings, or both,to plain end sink tailpieces. The assembly consists of a stainless steel outerband with bolt and rubber adapter with TFE adapter seal.Dimensions, in.Size Tailpiece StyleO.D. SizeRange2by112 Glass tail pipe

46、 extension, metal tubing, andlead tailpiece extensions1.48 to 1.532by134 Lead, glass, and cup sink 1.70 to 1.782by178 112 DWV glass pipe and fittings 1.82 to 1.90FIG. X1.5 Adapter CouplingC 1053 00 (2005)16NOTE 1Coupling is used for joining all sizes of glass DWV pipe andfittings. The assembly consi

47、sts of stainless steel outer band with bolt andrubber compression liner with TFE seal ring.Dimensions, in.Size A B C D112 3258 15163162312 318 15163163434 414 171631646 512 1123166814 734 17814FIG. X1.6 Coupling (Bead to Bead)NOTE 1Coupling is used for joining all sizes of beaded glass to plainend (

48、cut) glass pipe, lead, IPS metal, or plastic pipe.The assembly consistsof a stainless steel band and rubber compression liner with TFE seal ring.Dimensions, in.Size A B C D112 3234 1343162338 314 134316341116 414 211631646 558 29163166858 778 414FIG. X1.7 B/P Coupling (Bead to Plain End)C 1053 00 (2005)17ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determi