ASTM C1059-1999 Standard Specification for Latex Agents for Bonding Fresh To Hardened Concrete《硬化混凝土保持新鲜用乳胶作用剂》.pdf

1、Designation: C 1059 99Standard Specification forLatex Agents for Bonding Fresh To Hardened Concrete1This standard is issued under the fixed designation C 1059; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revisi

2、on. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers latex bonding agents, suitablefor brush, broom, or spray application, to bond fresh concreteto hardene

3、d concrete.1.2 These bonding agents are intended for bonding newconcrete to old concrete such as interior surfaces, floors,roadways, bridge decks, ramps, runways, walks, and curbs.1.3 The values stated in either inch-pound units or SI unitsshall be regarded separately as standard. Within the text, t

4、he SIunits are shown in brackets. The values stated in each systemmay not be exact equivalents, therefore, each system must beused independently of the other without combining values inany way.2. Referenced Documents2.1 ASTM Standards:C 1042 Test Method for Bond Strength of Latex SystemsUsed With Co

5、ncrete23. Classification and Use3.1 This specification provides for the classification of thelatex bonding agents in accordance with use.3.1.1 Type I (Redispersable), is restricted for use in interiorwork not subject to water immersion or high humidity.3.1.2 Type II (Non-redispersable), may be used

6、for areassubject to high humidity or immersion in water and is suitablefor use in other areas.4. Ordering Information4.1 Purchase orders for these materials shall identify:4.1.1 The number of this specification and the required type,and4.1.2 Supplementary requirements if necessary.5. Physical Proper

7、ties5.1 The material shall conform to the requirements of Table1 when tested in accordance with Test Method C 1042.6. Sampling6.1 For sampling of bulk quantities, a batch or lot shall beconsidered a unit of manufacture as prepared for shipment ormay consist of a blend of two or more production runs

8、ofmaterial. A composite sample shall be taken and it shallprovide a volume of at least 1 gal 4 L.6.2 When the bonding agent to be sampled is in containers,the sample shall be obtained by taking a portion out of thecontainers that is equal in number to the next integer largerthan the cube root of the

9、 total number of containers in the lot.Grab samples shall be taken from each container and they shallhave a volume of at least12 pt. 0.25 L.6.3 All the sample containers shall be sealed to preventleakage or dilution and shall be properly marked for identifi-cation and correlation.7. Rejection7.1 The

10、 purchaser has the right to reject the bonding agentif it fails to meet the bond strength requirement, appearscurdled or otherwise nonuniform, or if it has a rank odor.8. Packaging and Package Marking8.1 The proprietary name and type of the organic bondingagent and the net quantity in gallons or lit

11、res shall be plainlymarked on the containers in which the material is delivered.Similar information shall be provided in the shipping advicesaccompanying packaged or bulk shipments of admixtures.9. Keywords9.1 adhesives; bonding agents; latex1This specification is under the jurisdiction of ASTM Comm

12、ittee C-9 onConcrete and Concrete Aggregates and is the direct responsibility of SubcommitteeC09.25 on Organic Materials for Bonding, Patching, and Sealing.Current edition approved Feb. 10, 1999. Published May 1999. Originallypublished as C 1059 86. Last previous edition C 1059 91.2Annual Book of AS

13、TM Standards, Vol 04.02.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this s

14、tandard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years

15、andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee

16、, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2

17、959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Physical Property Requirements of Latex BondingAgentsLatexBond Strengthmin, psi MPaType IType II400 2.8 dry1250 8.6 after immersionC1059992