ASTM C1097-2007(2012) Standard Specification for Hydrated Lime for Use in Asphalt Cement or Bituminous Pavements《沥青水泥或沥青人行道用熟石灰的标准规格》.pdf

1、Designation: C1097 07 (Reapproved 2012)Standard Specification forHydrated Lime for Use in Asphalt Cement or BituminousPavements1This standard is issued under the fixed designation C1097; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisi

2、on, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers high calcium, dolomitic andmagnesian-hydrated lime for use in asphalt cement

3、 or bitumi-nous pavement.NOTE 1Hydrated lime, either calcitic, dolomitic, or magnesian,improves bonding of bitumen and aggregates which reduces susceptibilityto moisture damage, reduces age hardening by chemically stabilizingpolar compounds found in asphalts, and increases initial stiffness ofasphal

4、t mixtures.NOTE 2No attempt is made to present requirements for any by-product lime.1.2 This standard does not purport to address the safetyconcerns associated with its use. It is the responsibility of theuser of this standard to establish appropriate safety and healthpractices and determine the app

5、licability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2C25 Test Methods for Chemical Analysis of Limestone,Quicklime, and Hydrated LimeC50 Practice for Sampling, Sample Preparation, Packaging,and Marking of Lime and Limestone ProductsC51 Terminology Relating to

6、 Lime and Limestone (as usedby the Industry)C110 Test Methods for Physical Testing of Quicklime,Hydrated Lime, and LimestoneD8 Terminology Relating to Materials for Roads and Pave-mentsD242 Specification for Mineral Filler For Bituminous Pav-ing MixturesD546 Test Method for Sieve Analysis of Mineral

7、 Filler forBituminous Paving Mixtures3. Terminology3.1 For definitions of terms used in this specification, referto Terminology C51 or Terminology D8.4. Chemical Requirements4.1 Hydrated lime for use in bituminous paving mixturesshall conform to the following chemical composition:Calcium and Magnesi

8、um Oxides (on an LOI-free basis,minimum % )90.0Carbon Dioxide (taken at point of manufacture,maximum % )5.0Unhydrated Calcium and Magnesium Oxides (maximum% ) 5.0Free Moisture of Dry Hydrates (taken at point ofmanufacture, maximum %)2.04.2 The chemical analysis of the hydrated lime shall bedetermine

9、d in accordance with Test Methods C25.5. Physical Requirements5.1 Hydrated lime, either dry or slurry form, shall not havemore than 3.0 % retained on a No. 30 (600 m) sieve and notmore than 30 % retained on a No. 200 (75 m) sieve.NOTE 3Specification D242 also contains physical specifications forhydr

10、ated lime. Specification D242 includes four size gradations, expressedas percent passing the sieve. For the two size gradations included in bothSpecification D242 and Specification C1097, the specifications are thesame.5.2 The particle size of hydrated lime shall be determined inaccordance with Test

11、 Methods C110.NOTE 4Some hydrated limes may require a full 30-min wash time.NOTE 5The Test Methods C110 method for particle size analysis isrequired instead of the Test Method D546 method because the because theTest Methods C110 method uses a standardized spray nozzle and pressuregauge.6. Sampling,

12、Inspection, Packaging and Marking6.1 The sampling, inspection, rejection, retesting,packaging, and marking shall be done in accordance withPractice C50.7. Keywords7.1 additive; asphalt; bituminous; hydrated; lime; mineralfiller; mixtures ; modifier; pavement1This specification is under the jurisdict

13、ion of ASTM Committee C07 on Limeand is the direct responsibility of Subcommittee C07.02 on Specifications andGuidelines.Current edition approved Dec. 1, 2012. Published December 2012. Originallyapproved in 1990. Last previous edition approved in 2007 as C1097 07. DOI:10.1520/C1097-07R12.2For refere

14、nced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West C

15、onshohocken, PA 19428-2959. United States1ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and t

16、he riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision

17、of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shoul

18、dmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C1097 07 (2012)2