ASTM C1281-2003(2009) Standard Specification for Preformed Tape Sealants for Glazing Applications《镶嵌玻璃用预制密封条的标准规范》.pdf

1、Designation: C 1281 03 (Reapproved 2009)Standard Specification forPreformed Tape Sealants for Glazing Applications1This standard is issued under the fixed designation C 1281; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification describes preformed tape sealants foruse in glazing applications. These materials are generally

3、 usedto serve as components of glazing systems. They are intendedto serve as a water and air barrier.1.2 This specification is not intended for preformed foamtape sealants.1.3 The values stated in SI units are to be regarded as thestandard. The values in parentheses are provided for informa-tion pur

4、poses only.1.4 The subcommittee with jurisdiction is not aware of anysimilar ISO standard.1.5 The following precautionary statement pertains only tothe test method section of this specification. This standard doesnot purport to address all of the safety concerns, if any,associated with its use. It i

5、s the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM Standards:2C 717 Terminology of Building Seals and SealantsC 765 Test Method for Low-Temperature

6、Flexibility ofPreformed Tape SealantsC 771 Test Method for Weight Loss After Heat Aging ofPreformed Tape SealantsC 772 Test Method for Oil Migration or Plasticizer Bleed-Out of Preformed Tape SealantsC 879 Test Methods for Release Papers Used with Pre-formed Tape SealantsC 908 Test Method for Yield

7、Strength of Preformed TapeSealantsC 972 Test Method for Compression-Recovery of TapeSealantC 1016 Test Method for Determination of Water Absorptionof Sealant Backing (Joint Filler) MaterialC 1266 Test Method for Flow Characteristics of PreformedTape Sealants3. Terminology3.1 DefinitionsThe definitio

8、ns of the following terms usedin this specification are found in Terminology C 717: compres-sion seal, glazing, tape sealant.4. Materials and Manufacturers4.1 The preformed tape sealant shall be composed ofappropriate raw materials to result in conformance to thisspecification.4.2 The preformed tape

9、 sealant shall be of uniform dimen-sions and consistency.4.3 When properly applied, this material shall form a seal toprevent air and water from entering the system.5. Requirements5.1 The tape sealant in the original unopened container shallmeet the requirements of this specification and remain suit

10、ablefor use for a minimum of 12 months from the date ofmanufacture when stored at a temperature of 26.6C (80F)maximum.5.2 Physical PropertiesThe physical properties of thematerial shall conform to the requirements specified in Table 1.6. Significance and Use6.1 This specification describes only pref

11、ormed tape seal-ants for glazing applications. Their use is specific underglazing systems to serve as a water and air barrier. The testmethods chosen are to determine their efficiency in this use.1This specification is under the jurisdiction of ASTM Committee C24 onBuilding Seals and Sealants and is

12、 the direct responsibility of Subcommittee C24.10on Specifications, Guides and Practices.Current edition approved Jan. 1, 2009. Published March 2009. Originallyapproved in 1994. Last previous edition approved in 2003 as C 1281 03.2For referenced ASTM standards, visit the ASTM website, www.astm.org,

13、orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.This specificati

14、on does not describe all required properties ofthe preformed tape sealants. It should be recognized by thepurchaser and design professional that not all preformed tapesealants meeting this specification are suitable for all applica-tions. In some instances, additional requirements will be agreedto b

15、y the supplier and user.7. Sampling7.1 The preformed tape sealant to be tested for conformancewith the requirements of this specification shall be takendirectly from a randomly selected commercial container assupplied by the manufacturer.8. Test Methods8.1 All test methods described in the following

16、 paragraphs,unless otherwise indicated, shall be performed in a laboratorycontrolled at 23 6 2C (73.4 6 3.6F). This preformed tapesealant sample shall be conditioned at this temperature for atleast 24 h before laboratory tests are preformed.8.2 Low Temperature FlexibilityTest Method C 765.8.3 Weight

17、 LossTest Method C 771.8.4 Vehicle MigrationTest Method C 772.8.5 Backing RemovalTest Method C 879.8.6 Yield StrengthTest Method C 908.8.7 Compression/RecoveryTest Method C 972.8.8 Water AbsorptionTest Method C 1016, Procedure A,with Section 10.1.5 modified as follows: after immersion for 24h, remov

18、e the specimen by picking it up 75 mm (3 in.) from theends and blotting gently with an absorbent paper towel, takingcare not to squeeze or press the specimen while blotting.Within 1 min., place the specimen on the weighing platformand record the mass of the specimen to the nearest 0.1 g (0.004oz.).8

19、.9 Flow TestTest Method C 1266.9. Packaging and Package Marking9.1 Unless otherwise specified in the contract or order, thematerial shall be packaged in standard commercial containersconstructed to ensure acceptance by common or other carrierfor safe transportation to the point of delivery.9.2 Shipp

20、ing containers shall be marked with the name,grade, and quantity of the material contained therein, as definedby the contract or order under which the shipments are made.The name of the manufacturer, the lot and batch number of thecontract or order, and the date of manufacture shall also beshown.10.

21、 Keywords10.1 glazing; glazing tapes; preformed tape sealant; tapespecificationASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the vali

22、dity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comm

23、ents are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have

24、not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple c

25、opies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Material RequirementsProperties ASTM Test Method RequirementsLow Temp Flex C 765 No Cracks at

26、23C (10F)No Adhesion LossWeight Loss C 771 2 % MaximumVehicle Migration C 772 1 paper stained maximum and thisstain can be no more than 3.2 mm(0.125 in.) from edge of samplemaximumBacking Removal C 879,Alternative ANo transfer of tape compound to thepaper.C 879,Alternative BNo transfer of tape compound to thepaperYield Strength C 908 41.4 kPa (6 psi) minimumCompression/RecoveryC 972 122 N/cm3(450 lbf/in.3) max.Compression IndexWater Absorption C 1016 0.04 g/cm3Weight Gain maximumafter blottingFlow Test C 1266 60 % max Loss of HeightC 1281 03 (2009)2