ASTM C1302-2004 Standard Guide for Selection and Use of Keywords for Thermal Insulation Test Methods and Standards《隔热试验方法及标准的关键词选择和使用标准指南》.pdf

1、Designation: C 1302 04Standard Guide forSelection and Use of Keywords for Thermal Insulation TestMethods and Standards1This standard is issued under the fixed designation C 1302; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the

2、year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This guide has been prepared for use by ASTM techni-cal committees and others in the preparation of ASTM stan

3、-dards pertaining to thermal insulations and to materials asso-ciated with them.1.2 The keywords appear in alphabetical order.1.3 All ASTM standards require a list of appropriate termsfor indexing called Keywords. Keywords shall be listed at theend of the draft standard and will appear in the publis

4、heddocument.2. Significance and Use2.1 The purpose of the keyword list is to provide a standardset of words that can be used in the preparation and referenceof documents. Keywords are used to search for information.2.2 Keywords are not defined in this guide.2.3 Words referring to the singular includ

5、e the plural also.3. Keywords3.1absorptionacousticaladhesionadhesiveaircraftaluminumaluminum foilapparentapplicationaustenitic stainless steelbacker boardbattsblack bodyblanketblockboardboil-off calorimeterbreaking loadbreaking strengthbubble-pack insulationbubble-pack reflective insulationbuilding

6、envelopebuilding insulationbuilding technologybulk densityburn potentialcalcium silicatecalculated energy savingscalibrationcalorimeterceiling panelsceiling tilescellular glasscellular materialscellular plasticcellular polystyrenecellulosecellulosic fibercementchemical analysischloridecoatingscompos

7、itecomposite foam insulation boardcompressive pressurecompressive resistancecompressive strengthcomputer programconditioningconsistencyconstruction and installationconvergence factorcorkcorrosioncrackingcryogenic temperaturescuringdata time intervaldeflectiondeformation1This guide is under the juris

8、diction of ASTM Committee C16 on ThermalInsulation and is the direct responsibility of Subcommittee C16.95 on Editorial.Current edition approved May 1, 2004. Published May 2004. Originallyapproved in 1995. Last previous edition approved in 2002 as C 1302 95 (2002).1Copyright ASTM International, 100

9、Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.delaminationdensitydesigndesign densitydished head segmentdoorsduct linerduct workducts and equipmentdustdynamic measurementelectrolytic copperelevated temperatureemittanceerror analysisevacuated insulationevacuated refl

10、ective insulationexpanded perliteexpanded vermiculiteexpansionexperimental designexterior exposure testfaced foam boardfaced insulationfacingfeltfenestrationfibrous glassfinishingfire resistiveflanking lossflexibilityflexibleflexural strengthfluoridefoamfoil laminatesframe constructionfriabilityfull

11、 scale testingfungi resistanceglass fibergranulargranular loose-fillguarded hot plate apparatushealth hazardsheatheat flowheat flow meter apparatusheat fluxheat flux transducerheat gainheat lossheat transferhemisphericalhigh temperature calculationhigh temperature insulationhot-boxhot-surface perfor

12、mancehumid aginghydraulic-settingimmersionin-situ measurementindustrial applicationinfrared inspectioninorganic fiberinstrument verificationinsulating cementinsulationinsulation coverinsulation systeminterior radiation control coatingsintermediate density sheathinginterpretation of field dataIR emmi

13、tancejacketing materiallaminateleachable chlorideslengthlight frame constructionline source heaterlinear changeslinearityliningloading testsloose filllow emittancelow permeancelow temperature insulationlow-densitymanufactured housingmass lossmasticmaterialmathematical modelmean test temperaturemecha

14、nical processmembrane-facedmetal buildingmetal-mesh coveredmetallic reflective insulationmethod of mixturesmineral fiberminimum use temperaturemodulus of elasticitymodulus of rupture (MOR)moisture contentmoldedmounting of heat flux transducersmulti-foil insulationmultilayer insulationsnormal emittan

15、cenuclear power plantoutdoor service vesselpaint-high reflectancepaint-high temperatureC1302042paint-spray appliedparting strengthpenetrationperformance criteriaperlitepermeabilitypHphenolicphysical propertiespipe densitypipe insulationpipe systemspipe thermal insulation diameterpipe thermal insulat

16、ion dimensionpipe thermal insulation thicknessplane and radial calculationplastic sheet and filmplastics (general)polyethylene terephthalate reference filmpolyisocyanuratepolystyrenepolyurethaneprecision V-groovepreconditioningprefabricated insulationprefabricated panelpreformedpreformed thermal ins

17、ulationprogram verificationpropertiespseudo steady-statequality controlR-valueradial heat transferradiant barrier systemradiationradiation barrierradiation control coatingsradiative transportreflectancereflective air spacereflective coatingreflective insulationreflective linerreflective paintreflect

18、ive pipe insulationreflective systemreflectivityregular density sheathingremovableremovable/reusablerepairrigidrigid cellular plasticrigid cellular polyisocyanuraterigid cellular polystyrenerigid cellular polyurethanerigidityroof deckroof inspectionroof insulationsamplingsampling and acceptance crit

19、eriaselecting temperaturesselectionselection and applicationsensor calibrationsensor locationsheetsheet materialsheet radiant barriershrinkagesilicatesingle-sidedsoaking heat testsodiumsolar reflectancesound deadening boardspecific heatspray applicationspray appliedsquarenesssteady statestress corro

20、sion crackingstructural insulationsummation techniquesurface resistancetemperature testtenacitytensile strengthtensiontest specimen preparationthermalthermal capacitythermal conductancethermal conductivitythermal contactthermal diffusivitythermal insulating cementsthermal insulating materialthermal

21、insulating materialsblanketthermal insulating materialsblock and boardthermal insulating materialsblock and pipethermal insulating materialsboardthermal insulating materialscementthermal insulating materialsglassthermal insulating materialsloose fillthermal insulating materialsmineral fiberthermal i

22、nsulating materialspipethermal insulating materialspreformedthermal insulating materialsreflectivethermal insulating materialsrigidthermal insulationthermal insulation applicationthermal insulating fitting coverthermal insulation for austenitic stainless steelC1302043thermal insulation handlingtherm

23、al insulation permeability filmthermal insulation storagethermal integritythermal performancethermal propertythermal resistancethermal resistivitythermal testingthermal transmissionthermesthesiometerthicknessthin-heater apparatustime-averaged vapor pressuretotal hemispherical emittancetransducer des

24、igntransducer sensitivitytransmission-water vaportransverse strengthtruenesstubing thermal insulation thicknesstubulartumble testU-valueunguarded hot platevapor barrier finishvapor retarderverificationvermiculitevessel laggingvolume changevolume losswall sheathingwarpagewater absorptionwater equival

25、entwater retentionwater vapor permeancewater vapor sorptionwater vapor transmissionwet covering capacitywet insulationwidthwindowASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard ar

26、e expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not

27、revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which yo

28、u may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).C1302044