ASTM C1319-2016 Standard Specification for Concrete Grid Paving Units《混凝土格子铺设装置的标准规格》.pdf

1、Designation: C1319 16Standard Specification forConcrete Grid Paving Units1This standard is issued under the fixed designation C1319; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses

2、 indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification covers the requirements for concretegrid paving units for vehicular trafficways, parking areas, soilstabilization, and revetments.NOTE 1

3、When particular features are desired, such as weightclassification, higher compressive strength, surface texture, finish, color,or other special features, such properties should be specified separately bythe purchaser. However, local sellers should be consulted as to availabilityof units having the

4、desired features.1.2 The text of this standard references notes and footnoteswhich provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be consideredas requirements of the standard.1.3 The values stated in inch-pound units are to be regardedas stan

5、dard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2C33 Specification for Concrete AggregatesC140 Test Methods for Sampling and Testing ConcreteMasonry Units and

6、 Related UnitsC150 Specification for Portland CementC331 Specification for Lightweight Aggregates for ConcreteMasonry UnitsC595 Specification for Blended Hydraulic CementsC618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC989 Specification for Slag Cement for

7、 Use in Concrete andMortarsC979 Specification for Pigments for Integrally Colored Con-creteC1157 Performance Specification for Hydraulic CementC1232 Terminology of MasonryC1240 Specification for Silica Fume Used in CementitiousMixtures3. Terminology3.1 Terminology defined in Terminology C1232 shall

8、applyfor this specification.4. Materials4.1 Cementitious MaterialsMaterials shall conform to thefollowing applicable ASTM specifications:4.1.1 Portland CementsSpecification C150.4.1.2 Modified Portland CementPortland cement con-forming to Specification C150, modified as follows:4.1.2.1 Calcium carbo

9、nate, with a minimum 85 % CaCO3content, shall be permitted to be interground with the cement,provided the requirements of Specification C150 as modifiedare met: limitation on insoluble residue is 1.5 % and limitationon loss on ignition is 7 %.4.1.3 Blended Hydraulic CementsSpecification C595.4.1.4 H

10、ydraulic CementSpecification C1157.4.1.5 PozzolansSpecification C618.4.1.6 Blast Furnace Slag CementsSpecification C989.4.1.7 Silica FumeSpecification C1240.4.2 AggregatesAggregates shall conform to one of thefollowing ASTM specifications, except that grading require-ments shall not necessarily appl

11、y:4.2.1 Normal WeightSpecification C33.4.2.2 LightweightSpecification C331.4.3 Pigments for Integrally Colored ConcreteSpecification C979.4.4 Other ConstituentsAir-entraining agents, integral wa-ter repellents, and other constituents, shall be previouslyestablished as suitable for use in concrete gr

12、id paving units andshall conform to applicable ASTM standards, or they shall beshown by test or experience satisfactory to the specifier and notto be detrimental to the durability of the concrete grid pavingunit or any material customarily used in grid paving construc-tion.5. Physical Requirements5.

13、1 Units shall have maximum length and width dimensionsof 24 in. by 24 in. (610 mm by 610 mm).1This specification is under the jurisdiction of ASTM Committee C15 onManufactured Masonry Units and is the direct responsibility of SubcommitteeC15.03 on Concrete Masonry Units and Related Units.Current edi

14、tion approved Dec. 1, 2016. Published January 2017. Originallyapproved in 1995. Last previous edition approved in 2014 as C1319 14. DOI:10.1520/C1319-16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMSt

15、andards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard wa

16、s developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.2 Units sh

17、all have a minimum specified thickness of 318in. (80 mm).5.3 At the time of delivery to the work site, the units shallconform to the physical requirements prescribed in Table 1.5.4 DurabilityDurability shall be demonstrated by provenfield performance satisfactory to the specifier that the gridpaver

18、units have adequate durability for the intended use.5.4.1 Proven Field PerformanceSatisfactory field perfor-mance is demonstrated when units similar in composition andmade with the same manufacturing process as those to besupplied to the purchaser, maintain the physical requirementsspecified in Tabl

19、e 1 after three years of use. The units used asthe basis for proven field performance shall have been exposedto the same general type of environment, temperature range,and traffic volume as is expected for the units supplied to thepurchaser.6. Permissible Variations in Dimensions6.1 Length or width

20、of units shall not differ by more than618 in. (63.2 mm) from specified dimensions. Heights of unitsshall not differ by more than 618 in. (63.2 mm) from thespecified dimensions. Tests shall be performed as required in7.2.7. Sampling and Testing7.1 The purchaser or his authorized representative shall

21、beaccorded proper facilities to inspect and sample the units at theplace of manufacture from lots ready for delivery.7.2 Compressive strength, absorption, density, and dimen-sional tolerances shall be based on tests of concrete grid pavingunits of any configuration or dimensions made with the samema

22、terials, concrete mix design, manufacturing process, andcuring method, conducted in accordance with Test MethodsC140 and within 12 months of production of the units.8. Visual Inspection8.1 Units shall be free of defects that interfere with theproper placing of the unit or impair the strength or perm

23、anenceof the construction.9. Compliance9.1 If a sample fails to conform to the specifiedrequirements, the manufacturer shall be permitted to removeunits from the shipment. A new sample shall be selected by thepurchaser from remaining units from the shipment with asimilar configuration and dimension

24、and tested at the expenseof the manufacturer. If the second sample meets the specifiedrequirements, the remaining portion of the shipment repre-sented by the sample meets the specified requirements. If thesecond sample fails to meet the specified requirements, theremaining portion of the shipment re

25、presented by the samplefails to meet the specified requirements.NOTE 2Unless otherwise specified in the purchase order, the costs oftests is typically borne as follows: (1) if the results of the tests show thatthe units do not conform to the requirements of this specification the costis typically bo

26、rne by the seller; (2) if the results of the tests show that theunits conform to the specification requirements, the cost is typically borneby the purchaser.10. Keywords10.1 concrete grid paving units; revetments; soil stabiliza-tion; vehicular trafficwaysSUMMARY OF CHANGESCommittee C15 has identifi

27、ed the location of selected changes to this standard since the last issue(C1319 14) that may impact the use of this standard. (December 1, 2016)(1) Revised Table 1.TABLE 1 Physical RequirementsCompressive StrengthNet Area,min. psi (MPa)Water Absorption,max lb/ft3(kg/m3)Percent Solid,min. and max.,%W

28、eb Widthin. (mm)Average of 3 units Individual Average of 3 units Individual MinimumAAverageB5000 (35) 4500 (31) 10 (160) 12 (192) 45 and 75 1.00 (25) 1.25 (32)AMeasured at the thinnest point.BAverage of measurements along the height of the web.C1319 162ASTM International takes no position respecting

29、 the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standar

30、d is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International

31、 Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.Thi

32、s standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 163