ASTM C1330-2002(2013) Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants《与冷却液密封胶一起使用的圆柱形密封胶衬标准规格》.pdf

1、Designation: C1330 02 (Reapproved 2013)Standard Specification forCylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants1This standard is issued under the fixed designation C1330; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the basic requirements forcylindrical sealant backing to be used with

3、 cold liquid appliedsealants for use in building seals.1.2 Cylindrical sealant backing serves one or more of thefollowing functions:1.2.1 Limits the amount and depth of sealant applied into ajoint,1.2.2 Acts as a bond breaker to allow joint movementwithout undue stress to the sealant,1.2.3 Provides

4、a form to assist the sealant in developing theproper shape factor, and1.2.4 Acts as a barrier to the flow of sealant through thejoint.1.3 The committee with jurisdiction over this standard is notaware of any comparable standards published by other ASTMcommittees or other organizations.1.4 This speci

5、fication may involve hazardous materials,operations, and equipment. This standard does not purport toaddress all of the safety concerns, if any, associated with itsuse. It is the responsibility of the user of this standard toestablish appropriate safety and health practices and deter-mine the applic

6、ability of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C717 Terminology of Building Seals and SealantsC1016 Test Method for Determination of Water Absorptionof Sealant Backing (Joint Filler) MaterialC1087 Test Method for Determining Compatibility ofLiquid-Applied S

7、ealants with Accessories Used in Struc-tural Glazing SystemsC1253 Test Method for Determining the Outgassing Poten-tial of Sealant BackingD1622 Test Method for Apparent Density of Rigid CellularPlasticsD1623 Test Method for Tensile and Tensile Adhesion Prop-erties of Rigid Cellular PlasticsD5249 Spe

8、cification for Backer Material for Use with Cold-and Hot-Applied Joint Sealants in Portland-Cement Con-crete and Asphalt Joints3. Terminology3.1 DefinitionsThe definitions for the following termsused in this standard are found in Terminology C717:3.1.1 bi-cellular sealant backing, bond breaker, clos

9、ed cell,joint, open cell, outgassing, seal, sealant, sealant backing, skin.4. Classification4.1 Cylindrical sealant backings are divided into threetypes.4.1.1 Type Ccylindrical flexible sealant backings com-posed predominately of closed cell material as defined inTerminology C717.4.1.2 Type Ocylindr

10、ical flexible sealant backings com-posed of predominantly open cell material as defined inTerminology C717.4.1.3 Type Bcylindrical flexible sealant backings com-posed of bi-cellular material as defined in Terminology C717.5. Significance and Use5.1 This specification is designed to give some indicat

11、ion asto the differences in performance for various cylindrical sealantbackings.5.2 Although this specification qualifies a cylindrical sealantbacking for use, it does not address the compatibility of thebacking with the sealants with which it will make contact.Sealant compatibility should be confir

12、med by the sealantmanufacturer. Compatibility characteristics of sealants in con-tact with cylindrical sealant backings can be determined byTest Method C1087.6. Test Methods6.1 Water AbsorptionTesting for water absorption shall bemade in accordance with Test Method C1016, Procedure B.1This specifica

13、tion is under the jurisdiction of ASTM Committee C24 onBuilding Seals and Sealants and is the direct responsibility of Subcommittee C24.10on Specifications, Guides and Practices.Current edition approved May 1, 2013. Published May 2013. Originallyapproved in 1996. Last previous edition approved in 20

14、07 as C133002(2007). DOI:10.1520/C1330-02R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM I

15、nternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16.2 DensityTesting for density shall be made in accor-dance with Test Method D1622.6.3 OutgassingTesting for outgassing shall be made inaccordance with Test Method C1253.6.4 Compression Deflection and R

16、ecoveryTesting to bemade in accordance with Specification D5249.6.5 Tensile StrengthTesting for tensile strength to be madein accordance with Test Method D1623. In all cases use asample length sufficient to fit the tensile testing equipment.6.6 Use of a58 in. diameter sample shall be standard.7. Sam

17、pling7.1 Samples used for testing shall be taken directly from thepackage as commercially supplied by the manufacturer.8. Physical Properties8.1 Physical properties of the cylindrical sealant backingmaterial shall conform to the requirements of Table 1.9. Workmanship, Finish, and Appearance9.1 The p

18、roduct shall be clean, free of scale, foreign matter,oil, or water which could wipe off on a joint sidewall andinterfere with the proper cure or adhesion of the sealant.10. Packaging and Package Marking10.1 Packaging shall be marked with the following infor-mation:10.1.1 Name, brand, or trademark of

19、 the manufacturer,10.1.2 Quantity and size,10.1.3 ASTM designation (Type C, O, or B), and10.1.4 Any other information that the manufacturer re-quires.11. Keywords11.1 backer rod; cylindrical sealant backing; joint backing;sealant backingASTM International takes no position respecting the validity of

20、 any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to

21、revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Y

22、our comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is co

23、pyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.

24、org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Sealant Backer PropertiesNOTE 1This table applies to cylindrical sealant backing for use withcold liquid applied sealants.Property Test Method Type C Type B Type OWater absorption (g/cc) C1016Procedure B0.10Density (kg/m3) D1622 2448 2448 2448Outgassing (No. of bubbles) C1253 1 90 90 90Compression deflection (kPa) D5249 20.5 20.5 200 200 100C1330 02 (2013)2