ASTM C1369-2007(2014) Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units《釉面结构绝缘玻璃件的二级边缘密封剂的标准规格》.pdf

1、Designation: C1369 07 (Reapproved 2014)Standard Specification forSecondary Edge Sealants for Structurally Glazed InsulatingGlass Units1This standard is issued under the fixed designation C1369; the number immediately following the designation indicates the year oforiginal adoption or, in the case of

2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification describes the properties of cold,liquid-applied, single or multi-component,

3、chemically curing,elastomeric sealants used as the secondary seal of sealedinsulating glass units, hereinafter referred to as the “sealant”(see Fig. 1). These sealants are intended to be a structuralcomponent of sealed insulating glass (IG) units used instructural sealant glazing (hereinafter referr

4、ed to as SSG).Typical designs and considerations can be found in GuideC1249. Presently only certain silicone sealants are recognizedas having the necessary durability for use as secondary sealantin IG units in SSG applications.1.2 This specification does not describe all of the necessaryproperties o

5、f the sealant. Only those properties for which thereare ASTM test methods and industry-agreed-upon minimumacceptable test requirements are described by this specification.Additional properties will be added as ASTM test methods forthese properties become available.1.3 This specification only address

6、es the durability of thesecondary edge sealants for structurally glazed insulating glassunits. Durability of sealed insulating glass units can be found inspecifications and guides that reside within ASTM CommitteeE06.1.4 The committee with jurisdiction for this standard is notaware of any comparable

7、 standard published by other organi-zations.1.5 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationpurposes only.2. Referenced Documents2.1 ASTM Standards:2C603 Test Method for Extrusion Rate and Application Lifeof Elastomeric Sealants

8、C639 Test Method for Rheological (Flow) Properties ofElastomeric SealantsC661 Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a DurometerC679 Test Method for Tack-Free Time of Elastomeric Seal-antsC717 Terminology of Building Seals and SealantsC792 Test Method for Effec

9、ts of HeatAging on Weight Loss,Cracking, and Chalking of Elastomeric SealantsC1135 Test Method for Determining Tensile Adhesion Prop-erties of Structural SealantsC1184 Specification for Structural Silicone SealantsC1249 Guide for Secondary Seal for Sealed Insulating GlassUnits for Structural Sealant

10、 Glazing ApplicationsC1265 Test Method for Determining the Tensile Propertiesof an Insulating Glass Edge Seal for Structural GlazingApplications3. Terminology3.1 DefinitionsRefer to Terminology C717 for definitionsof the following terms used in this specification: chemicallycuring sealant, compatibi

11、lity, cure, cured, elastomeric,hardness, non-sag sealant, sealant, shelf life, silicone sealant,and substrate.4. Classification of Sealants4.1 A sealant qualifying under this specification shall beclassified as to type and use as follows:4.1.1 Type SA single-component sealant.1This specification is

12、under the jurisdiction of ASTM Committee C24 onBuilding Seals and Sealants and is the direct responsibility of Subcommittee C24.10on Specifications, Guides and Practices.Current edition approved June 1, 2014. Published July 2014. Originally approvedin 1997. Last previous edition approved in 2007 as

13、C136907. DOI: 10.1520/C1369-07R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM Internationa

14、l, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.2 Type MA multi-component sealant.4.1.3 Use GA sealant that meets the requirements of thisspecification when tested on clear, uncoated float glass sub-strates.4.1.4 Use OA sealant that meets the requirements o

15、f thisspecification when tested on coatings3such as reflective andlow-emissivity metallic materials applied to glass substrates.5. Materials and Manufacture5.1 Sealant:5.1.1 Furnish single-component sealants as a homogeneousmixture of a consistency suitable for application. Apply thesealant in stric

16、t accordance with the written recommendationsof the sealant manufacturer. The cured sealant shall be anelastomeric solid.5.1.2 Multi-component sealants shall be mixed in the cor-rect ratio4of components and delivered by appropriate equip-ment as specified by the sealant manufacturer.6. Requirements6

17、.1 The physical, mechanical, and performance propertiesof the sealant shall conform to the requirements described inTable 1.6.2 The standard substrate for this specification is clear,uncoated float glass. If metallic coated5glass substrates are tobe qualified by this specification, they shall be tes

18、ted by TestMethod C1135 as required in 8.1.6.6.3 The sealant shall be compatible with the components ofthe edge seal.3Reflective and low-emissivity metallic materials are typical coatings applied tothe glass substrate. If the coatings are edge deleted for actual production, theyshould be edge delete

19、d for use in this specification.4If the mix ratio of multi-component sealant is not within the sealant manufac-turers recommendations, the cure rate, tack free time, cohesive strength, andadhesive strength of the sealant can be adversely affected.5Metallic coatings that require a sealed air space ar

20、e typically edge deleted inregular production. They must also be edge deleted for this testing.FIG. 1 Cutaway Section of IG Unit Edge SealTABLE 1 Requirements for Physical, Mechanical, and Performance Qualities of the SealantProperty Requirements Test MethodExtrudability 10 s, max C603Rheological, m

21、ax C639Vertical 4.8 mm (316 in.)Horizontal noneHardness, Shore A 20 to 60 C661Heat Aging C792Weight Loss, max 10 %Cracking noneChalking noneDurabilityTensile Value, min 8.1.6Standard Conditions 345 kPa (50 psi)88C (190F) 345 kPa (50 psi)29C (20F) 345 kPa (50 psi)Water Immersion 345 kPa (50 psi)5000h

22、 Weathering 345 kPa (50 psi)Shelf Life, min 6 months 8.1.7C1369 07 (2014)27. Significance and Use7.1 Not all sealants meeting this specification should bepresumed to be suitable for all applications and all substrates.This specification assists in selecting sealants that meet certainminimum standard

23、s of performance.7.2 This specification does not evaluate the adhesion of thesecondary sealant to the IG unit spacer. Adhesion of thesecondary sealant to the spacer is generally considered neces-sary for the successful performance of the IG unit edge seal.7.3 When specifying a sealant using this spe

24、cification, it isessential that the applicable type and use also be included in therequirements. This will ensure that the proper sealant isprovided for the intended use.7.4 IG units qualified by this specification shall have a lowmoisture vapor transmission sealant for a primary seal and astructura

25、l silicone sealant for a secondary seal.7.5 This specification does not address appropriate sealantstiffness since the appropriate stiffness is a function of theparticular insulating glass system in which the sealant is used(that is, varies with spacer, shape and set back, and sealantconfiguration).

26、 Test Method C1265 can assist in evaluatingthese aspects of the sealant in a particular IG system.8. Test Methods8.1 Sealant:8.1.1 ExtrudabilitySee Test Method C603.8.1.2 Rheological PropertiesSee Test Method C639, us-ing test procedures for Type II and IV sealants.8.1.3 HardnessSee Test Method C661

27、, using a Type A-2durometer.8.1.4 Heat AgingSee Test Method C792, using a tempera-ture of 88 6 5C (190 6 10F).8.1.5 Tack Free TimeSee Test Method C679.8.1.6 DurabilitySee Test Method C1135 as modified in8.6 through 8.6.2.5 of Specification C1184. (See Table 1.)8.1.7 Shelf LifeMeet the requirements o

28、f Table 1 when thesealant has been stored in original, unopened container(s) attemperatures in accordance with recommendations from themanufacturer.9. Keywords9.1 edge sealant; IG unit; insulating glass; secondary seal-ant; structural glazingAPPENDIX(Nonmandatory Information)X1. COMMENTARYX1.1 This

29、specification does not address all the performancecriteria necessary for an adequate technical description ofstructural silicone sealants used in insulating glass units. Someimportant performance criteria not evaluated in this specifica-tion include: durability, fatigue cycling, ultimate elongation,

30、shear value, and long-term dead load capacity.X1.2 Input is requested from users of this specification inhelping to identify, as well as develop, future performancecriteria. Your participation is critical to the timely developmentof this specification.X1.3 At the time of initial publication of this

31、specification,it was decided that publishing this specification in its presentform was necessary for the use by the structural glazingindustry even though it is acknowledged to be incomplete andstill under development.ASTM International takes no position respecting the validity of any patent rights

32、asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any tim

33、e by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will r

34、eceive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM I

35、nternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 07 (2014)3