ASTM C139-2010 Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes《雨水井和人孔建造用混凝土砌块的标准规格》.pdf

1、Designation: C139 10Standard Specification forConcrete Masonry Units for Construction of Catch Basinsand Manholes1This standard is issued under the fixed designation C139; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of

2、 last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope*1.1 This specification covers solid pre

3、cast segmental con-crete masonry units made from hydraulic cement, water, andsuitable mineral aggregates, with or without the inclusion ofother materials. The units are intended for use in the construc-tion of catch basins and manholes.1.2 The text of this standard referenced notes and footnoteswhic

4、h provide explanatory material. These notes and footnotes(excluding those in tables and figures) shall not be consideredas requirements of the standard.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units tha

5、t are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2C33 Specification for Concrete AggregatesC140 Test Methods for Sampling and Testing ConcreteMasonry Units and Related UnitsC150 Specification for Portland CementC207 Specification for Hydrat

6、ed Lime for Masonry Pur-posesC595 Specification for Blended Hydraulic CementsC618 Specification for Coal Fly Ash and Raw or CalcinedNatural Pozzolan for Use in ConcreteC989 Specification for Slag Cement for Use in Concreteand MortarsC1157 Performance Specification for Hydraulic CementC1232 Terminolo

7、gy of Masonry3. Terminology3.1 Terminology defined in Terminology C1232 shall applyfor this specification.4. Materials4.1 Cementitious materials shall conform to the followingASTM specifications:4.1.1 Portland Cement Specification C150.4.1.2 Blended Hydraulic CementsSpecification C595.4.1.3 Hydrauli

8、c CementSpecification C1157.4.1.4 Ground Blast-Furnace SlagSpecification C989.4.1.5 Hydrated Lime Type S of Specification C207.4.1.6 Fly AshSpecification C618.4.1.7 Siliceous and Pozzolanic MaterialsSiliceous andpozzolanic materials shall conform to applicable ASTM stan-dards, or shall be shown by t

9、est or experience to be notdetrimental to the durability of the concrete.4.2 AggregatesAggregates shall conform to SpecificationC33, except grading requirements shall not apply.4.3 Other ConstituentsAir-entraining agents, coloringpigments, integral water repellents, finely ground silica, andother co

10、nstituents shall be previously established as suitable foruse in concrete masonry units and shall conform to applicableASTM standards or shall be shown by test or experience not tobe detrimental to the durability of the concrete masonry unitsor any material customarily used in masonry construction.1

11、This specification is under the jurisdiction of ASTM Committee C15 onManufactured Masonry Units and is the direct responsibility of SubcommitteeC15.03 on Concrete Masonry Units and Related Units.Current edition approved Dec. 1, 2010. Published December 2010. Originallyapproved in 1938. Last previous

12、 edition approved in 2005 as C139 05. DOI:10.1520/C0139-10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1*

13、A Summary of Changes section appears at the end of this standard.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Physical Requirements Physical Requirements5.1 At the time of delivery to the site of the work, the unitsshall conform

14、 to the requirements prescribed in Table 1.6. Dimensions and Permissible Variations6.1 The thickness of any unit shall be not less than 5 in. (127mm).6.2 Overall dimensions shall not vary by more than 6 3%from the specified dimensions.7. Sampling and Testing7.1 The purchaser or his authorized repres

15、entative shall beaccorded proper facilities to inspect and sample the units at theplace of manufacture from the lots ready for delivery.7.2 Units shall be sampled and tested in accordance withTest Methods C140.7.3 Except as specified in Section 8, and unless otherwiseagreed, the expense of inspectio

16、n and testing shall be borne bythe purchaser.8. Visual Inspection8.1 All units shall be sound and free of cracks or otherdefects that interfere with the proper placing of the unit.9. Compliance9.1 If a sample fails to conform to the specified require-ments, the manufacturer shall be permitted to rem

17、ove unitsfrom the shipment. A new sample shall be selected by thepurchaser from remaining units from the shipment with asimilar configuration and dimension and tested at the expenseof the manufacturer. If the second sample meets the specifiedrequirements, the remaining portion of the shipment repre-

18、sented by the sample meets the specified requirements. If thesecond sample fails to meet the specified requirements, theremaining portion of the shipment represented by the samplefails to meet the specified requirements.NOTE 1Unless otherwise specified in the purchase order, the cost oftests is typi

19、cally borne as follows: (1) if the results of the tests show thatthe units do not conform to the requirements of this specification, the costis typically borne by the seller; (2) if the results of the tests show that theunits conform to the specification requirements, the cost is typically borneby t

20、he purchaser.10. Keywords10.1 catch basins; concrete masonry units; manholes; ma-sonry unitsSUMMARY OF CHANGESCommittee C15 has identified the location of selected changes to this standard since the last issue (C139 05)that may impact the use of this standard. (Approved Dec. 1, 2010.)(1) Subsection

21、1.3 was added with the statement on units used.(2) References to Terminology standards were updated.(3) The SI conversion for water absorption in Table 1 wascorrected.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin th

22、is standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must b

23、e reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theres

24、ponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, W

25、est Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission ri

26、ghts to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).TABLE 1 Strength and Absorption RequirementsCompressive Strength, min, psi (MPa)(Average Gross Area)Water Absorption,max, lb/ft3(kg/m3)(Average of 3 Units)Average of 3 Units Individual Unit2500 (17) 2000 (13) 10 (160)C139 102