ASTM C1554-2018 Standard Guide for Materials Handling Equipment for Hot Cells.pdf

1、Designation: C1554 18Standard Guide forMaterials Handling Equipment for Hot Cells1This standard is issued under the fixed designation C1554; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in par

2、entheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 Intent:1.1.1 This guide covers materials handling equipment usedin hot cells (shielded cells) for the processing and handling ofnuclear and radioact

3、ive materials. The intent of this guide is toaid in the selection and design of materials handling equipmentfor hot cells in order to minimize equipment failures andmaximize the equipment utility.1.1.2 It is intended that this guide record the principles andcaveats that experience has shown to be es

4、sential to the design,fabrication, installation, maintenance, repair, replacement, anddecontamination and decommissioning of materials handlingequipment capable of meeting the stringent demands ofoperating, dependably and safely, in a hot cell environmentwhere operator visibility is limited due to t

5、he radiation expo-sure hazards.1.1.3 This guide may apply to materials handling equipmentin other radioactive remotely operated facilities such as suitedentry repair areas and canyons, but does not apply to materialshandling equipment used in commercial power reactors.1.1.4 This guide covers mechani

6、cal master-slave manipula-tors and electro-mechanical manipulators, but does not coverelectro-hydraulic manipulators.1.2 Applicability:1.2.1 This guide is intended to be applicable to equipmentused under one or more of the following conditions:1.2.1.1 The materials handled or processed constitute as

7、ignificant radiation hazard to man or to the environment.1.2.1.2 The equipment will generally be used over a long-term life cycle (for example, in excess of two years), butequipment intended for use over a shorter life cycle is notexcluded.1.2.1.3 The equipment can neither be accessed directly forpu

8、rposes of operation or maintenance, nor can the equipmentbe viewed directly, for example, without shielded viewingwindows, periscopes, or a video monitoring system.1.3 User Caveats:1.3.1 This standard is not a substitute for applied engineer-ing skills, proven practices and experience. Its purpose i

9、s toprovide guidance.1.3.1.1 The guidance set forth in this standard relating todesign of equipment is intended only to alert designers andengineers to those features, conditions, and procedures thathave been found necessary or highly desirable to the design,selection, operation and maintenance of r

10、eliable materialshandling equipment for the subject service conditions.1.3.1.2 The guidance set forth results from discoveries ofconditions, practices, features, or lack of features that werefound to be sources of operational or maintenance problems, orcauses of failure.1.3.2 This standard does not

11、supersede federal or stateregulations, or both, or codes applicable to equipment underany conditions.1.3.3 This standard does not cover design features of the hotcell, for example, windows, drains, and shield plugs. Thisstandard does not cover pneumatic or hydraulic systems. Referto Guides C1533, C1

12、217, and ANS Design Guides for Radio-active Material Handling Facilities hot cells; manipulator; materials handling;nuclear materials; remote handlingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. User

13、s of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every

14、five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technica

15、l committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken,

16、 PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1810