ASTM C629-2003 Standard Specification for Slate Dimension Stone《板条状规格石料标准规范》.pdf

1、Designation: C 629 03Standard Specification forSlate Dimension Stone1This standard is issued under the fixed designation C 629; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indi

2、cates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification covers the material characteristics,physical requirements, a

3、nd sampling appropriate to the selec-tion of slate for general building and structural purposes.1.2 Dimension slate shall include stone that is sawed, cut,split, or otherwise finished or shaped, and shall specificallyexclude molded, cast, or otherwise artificially aggregated unitscomposed of fragmen

4、ts, and also crushed and broken stone.1.3 It specifically excludes roofing slate (see SpecificationC 406) and slate for industrial uses.2. Referenced Documents2.1 ASTM Standards:2C119 Terminology Relating to Dimension StoneC 120 Test Methods for Flexure Testing of Slate (BreakingLoad, Modulus of Rup

5、ture, Modulus of Elasticity)C 121 Test Method for Water Absorption of SlateC 217 Test Method for Weather Resistance of SlateC 241 Test Method for Abrasion Resistance of Stone Sub-jected to Foot TrafficC 406 Specification for Roofing SlateC 1353 Test Method Using the Taber Abraser for AbrasionResista

6、nce of Dimension Stone Subjected to Foot Traffic3. Terminology3.1 DefinitionsAll definitions are in accordance with Ter-minology C119.4. Classification4.1 Dimension slate shall be selected for the following uses:4.1.1 I Exterior.4.1.2 II Interior.5. Physical Requirements5.1 Slate supplied under this

7、 specification shall conform tothe requirements listed in Table 1.5.2 Slate used for exterior applications in ambient acidicatmospheres or in industrial areas where heavy air pollutionoccurs shall be free of carbonaceous ribbons. Slate shall besound, durable, and free of spalls, cracks, open seams,

8、pits, orother defects that are likely to impair its structural integrity inits intended use.5.3 Slate shall be selected for overall satisfactory andnatural appearance.5.4 The desired color and texture, with their permissiblenatural variations in material characteristics for all material tobe produce

9、d for the project, shall be established by controlsamples. Select representative samples by viewing a sufficientnumber of physical samples prior to production that show thecomplete range of variations in color and texture of the slatespecified.6. Sampling6.1 Samples, if required, for testing to dete

10、rmine the char-acteristics and physical properties shall be representative of theslate to be used.1This specification is under the jurisdiction of ASTM Committee C18 onDimension Stone and is the direct responsibility of Subcommittee C18.03 onMaterial Specifications.Current edition approved Dec. 1, 2

11、003. Published January 2004. Originallyapproved in 1968. Last previous edition approved in 1999 as C 629 99.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the stan

12、dards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this st

13、andard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be rev

14、iewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsi

15、ble technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West C

16、onshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).TABLE 1 Physical Re

17、quirementsNOTEThe material property values in Table 1 were established using samples prepared according to the individual test methods. Finishes, other thanthose specified in the individual test methods, may result in a deviation from established values.PropertyTest Require-mentsClassificationsTestM

18、eth-od(s)Absorption, max,% 0.25 I Exterior C 1210.45 II InteriorModulus of rupture,min, psi (MPa):Across grain 9000 (62.1) I Exterior C 1207200 (49.6) II InteriorAlong grain 7200 (49.6) I Exterior5500 (37.9) II InteriorAbrasion resistance, 8.0 I Exterior C 241/C 1353min, HaA,B,C8.0 II InteriorAcid r

19、esistance, max, 0.015 (0.38) I Exterior C 217in. (mm) 0.025 (0.64) II InteriorAPertains only to stone subject to foot traffic.BThe supplier of the No. 60 Alundum abrasive, Norton, has indicated that the formula for Norton treatment 138S has been changed. The new abrasive is currrently moreaggressive

20、, resulting in lower abrasive hardness values (Ha) than when the standard was initially established. As such, care should be taken when interpreting Havaluesfrom tests using the new abrasive, particularly with regard to currentASTM stone standard specification requirements for abrasion resistance, w

21、hich were developed whenthe original abrasive was still in use. Committee C-18 is actively studying alternatives to address this issue.CAbrasion Resistance Test Method C 1353 will eventually replace Test Method C 241 and it is not necessary to perform both tests. Availability of the proper equipmentand materials by the testing laboratory may determine which test is performed.C629032