ASTM C774-1988(2011)e1 Standard Test Method for Yield Strength of Enameling Steels After Straining and Firing《搪瓷钢制品受应变和焙烧后的屈服强度的试验方法》.pdf

1、Designation: C774 88 (Reapproved 2011)1Standard Test Method forYield Strength of Enameling Steels After Straining andFiring1This standard is issued under the fixed designation C774; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, t

2、he year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTETest Method was corrected editorially in 2011INTRODUCTIONThe strength after strain and fire of a steel is a signif

3、icant factor in the strength of the final enameledware. This test provides a method to quantify the yield strength of enamel steels after straining andfiring by straining duplicate test plates to five different strain levels, exposing to a simulated enamelfire, and measuring the yield stress with a

4、standardized tensile pull test.1. Scope1.1 This test method covers determination of the yieldstrength of steel specimens after simulated forming and enamelfiring operations.1.2 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation

5、 only.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Refere

6、nced Documents2.1 ASTM Standards:2A370 Test Methods and Definitions for Mechanical Testingof Steel ProductsE8 Test Methods for Tension Testing of Metallic Materials3. Definition3.1 quarter linesimaginary lines parallel to the directionof rolling, positioned at a distance from the sheet mill edgeequa

7、l to one quarter of the sheet width.4. Summary of Test Method4.1 Representative sheet-steel specimens are selected,strained in tension to simulate forming, heat treated to simulateenamel firing, and tension tested for determination of yieldstrength.5. Significance and Use5.1 In the manufacture of po

8、rcelain enameled ware, sheetsteel is subjected to forming operations and subsequently tofiring of the enamel at temperatures, typically, of 1400 to1550F (760 to 844C). Some steels used for porcelainenameling are subject to grain growth in critically strainedareas resulting in loss of strength.5.2 Th

9、is may lead to easy deformation of the steel anddamage to the porcelain enamel coating.5.3 This test method may be correlated with transit or usetests to evaluate the suitability of steel for porcelain enameledware.6. Apparatus6.1 Shear for cutting blanks.6.2 Equipment for cutting or machining tensi

10、on specimens.6.3 Gage, 2-in. (50.8-mm), for marking tension specimens.6.4 Tension-Testing Equipment, as described in Test Meth-ods and Definitions A370.6.5 Specimen-Supporting Rack, slotted to support speci-mens on edge spaced 1 in. (25.4 mm) apart.6.6 Furnace, capable of heating the test specimens

11、and theirsupporting rack to the firing temperature in 2 min.1This test method is under the jurisdiction ofASTM Committee B08 on Metallicand Inorganic Coatings and is the direct responsibility of Subcommittee B08.12 onMaterials for Porcelain Enamel and Ceramic-Metal Systems.Current edition approved A

12、pril 1, 2011. Published April 2011. Originallyapproved in 1974. Last previous edition approved in 2006 as C774 88 (2006).DOI: 10.1520/C0774-88R11E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStanda

13、rds volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7. Reagents and Materials7.1 Sheet Steel, sufficient in size to provide the test speci-men, descr

14、ibed in Section 8.7.2 Solvent, such as acetone or isopropyl alcohol.7.3 Hydrochloric Acid (1+1)Dilute 1 volume of concen-trated hydrochloric acid (HCl, sp gr 1.19) with 1 volume ofwater.8. Sampling8.1 Obtain ten test samples, each approximately 1 by 9 in.(25 by 229 mm), from within the quarter lines

15、 of the sheetsample, the long dimension being in the direction of rolling.9. Procedure9.1 Remove burrs from the cut edges of the test samples.9.2 Mark 2-in. (50.8-mm) gage lengths in the middle of thetest samples and strain in tension. Maintain a minimum of 1 in.(25.4 mm) of length between the grips

16、 of the tension-testingmachine and the gage marks.9.3 Elongate duplicate test samples to nominal strain levelsof 0, 8, 12, 16, and 20 %. Measure the elongation withextensometers, dividers, or other means.9.4 Remove the test samples from the tension machine andmeasure actual strain to the nearest 0.0

17、1 in. (0.25 mm).9.5 Clean the strained test samples with the solvent and firein air atmosphere at 1450 6 10F (788 6 5C) for 4 min. Testsamples may be hung from hooks or supported on edge spaced1 in. (25.4 mm) apart (if the latter, be sure to support in amanner to prevent sagging during firing). The

18、test samplesshould reach the firing temperature within 2.0 6 0.5 min.9.6 Remove the samples from the furnace and air cool.9.7 Descale the fired samples in a HCl (1+1) solutioncontaining a few drops of an inhibitor, such as formaldehyde,at a temperature of 70 to 100F (21 to 38C). Promptly rinsethe te

19、st samples and dry.9.8 Machine the descaled test samples to make standardrectangular tension tests specimens in accordance with TestMethods and Definitions A370. The specimens shall have aminimum length of 8 in. (204 mm) and the sides of the reducedsection shall be parallel.9.9 Measure the thickness

20、 and width of each specimen, andtest for yield strength as described in Test Methods E8 at acrosshead speed of 0.10 in. (2.5 mm)/min. Determine the yieldstrength at the lower point or by the 0.5 % extension underload.10. Report10.1 Report the yield strengths determined for the duplicatespecimens at

21、each of the five strain levels.10.2 Report the actual strain imparted to each specimen.11. Precision and Bias11.1 The precision and bias of yield strength and strain inthis test method would be identical to the precision and bias ofTest Methods E8. Refer to this standard for up-to-date preci-sion an

22、d bias.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such righ

23、ts, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional

24、standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM

25、Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C774 88 (2011)12