ImageVerifierCode 换一换
格式:PDF , 页数:7 ,大小:115.22KB ,
资源ID:508550      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-508550.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(ASTM C857-2012a Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures 《地下预制混凝土公用设施的最低结构设计负荷的标准操作规程》.pdf)为本站会员(赵齐羽)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

ASTM C857-2012a Standard Practice for Minimum Structural Design Loading for Underground Precast Concrete Utility Structures 《地下预制混凝土公用设施的最低结构设计负荷的标准操作规程》.pdf

1、Designation:C85712 Designation: C857 12aStandard Practice forMinimum Structural Design Loading for UndergroundPrecast Concrete Utility Structures1This standard is issued under the fixed designation C857; the number immediately following the designation indicates the year oforiginal adoption or, in t

2、he case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes the minimum live loads and dead loads to be applied when desi

3、gning monolithic or sectional precastconcrete utility structures. Concrete pipe, box culverts, and material covered in Specification C478 are excluded from this practice.NOTE 1For additional information see AASHTO Standard Specification for Highway Bridges, Seventeenth Edition.NOTE 2The purchaser is

4、 cautioned that he must properly correlate the anticipated loading conditions and the field requirements with the design loadsused.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for i

5、nformation only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety and health practices and determine the applicability of regu

6、latorylimitations prior to use.2. Referenced Documents2.1 ASTM Standards:2C478 Specification for Precast Reinforced Concrete Manhole Sections2.2 AASHTO Standard:Specification for Highway Bridges, Seventeenth Edition33. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 dead loadswil

7、l consist of any other load that can affect the design of the structure.3.1.2 lifting insertdevice embedded or otherwise attached to the structure, designed and manufactured to support a measured,sustained, concentrated load.3.1.3 live loadswill consist of any moving loads that can affect the design

8、 of the structure and their associated impact andsurcharge loads.3.1.4 utility structurea structure that is used by electric, gas, communication, or similar industries.4. Design Loads4.1 RoofThe design loads for the roof of any structure at or below ground level consists of the live loads including

9、impactand dead loads that can develop as a result of earth pressure, hydrostatic pressure, and construction materials such as used forroadways and walkways.4.1.1 Live LoadsThe vehicle and pedestrian load designations are given in Table 1. Live load wheel spacing is shown in Fig.1.4.1.2 Impact:4.1.2.

10、1 The live loads A-16, A-12, and A-8 shouldshall be increased as follows to sustain the effect of impact:4.1.2.2 Live Load Increase:1This practice is under the jurisdiction of ASTM Committee C27 on Precast Concrete Products and is the direct responsibility of Subcommittee C27.10 on UtilityStructures

11、.Current edition approved Jan. 15, 2012. Published January 2012. Originally approved in 1978. Last previous edition approved in 20112012 as C857 112. DOI:10.1520/C0857-12A.2For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annu

12、al Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3Available from American Association of State Highway and Transportation Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,http:/www.transportation.org.1This docume

13、nt is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as ap

14、propriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.0 to 12 in. (0 to 305 mm) below ground level, 30 %13 to 24

15、in. (330 to 610 mm) below ground level, 20 %25 to 35 in. (635 to 889 mm) below ground level, 10 %TABLE 1 Vehicle and Pedestrian Load DesignationsDesignations Maximum Loads UsesA-16 (HS20-44)A16 000 lbf (71 172 N)/wheel heavy trafficA-12 (HS15-44)A12 000 lbf (53 376 N)/wheel medium trafficA-8 (H10-44

16、)A8 000 lbf (35 586 N)/wheel light trafficA-0.3 300 lbf/ft2(14.4 kPa) walkwaysBAThe designations in parentheses are the correspondingAASHTO designations.BAnticipated designs other than those listed should be designated by purchaser.FIG. 1 Live Load SpacingC857 12a236 in. (914 mm) or more below groun

17、d level, 0 %4.1.3 Dead LoadsDead loads will consist of the weight of the roof, roadbed, walkways, earth fill, access opening covers, andany other material that produces a static load.4.1.3.1 Recommended unit weights of materials for design calculations are as follows:Concrete, plain, and reinforced

18、150 lb/ft3(2043 kg/m3)Cast iron 450 lb/ft3(7208 kg/m3)Steel 490 lb/ft3(7850 kg/m3)Aluminum 175 lb/ft3(2804 kg/m3)Earth fill (dry) 110 lb/ft3(1762 kg/m3)Macadam 140 lb/ft3(2243 kg/m3)4.1.4 Distribution of Wheel Loads Through Earth Fills:4.1.4.1 Wheel loads at ground level shouldshall be considered ap

19、plied to a wheel load area as indicated in Fig. 2.4.1.4.2 Wheel loads shouldshall be distributed below ground level as a truncated pyramid, as shown in Fig. 3, in which the topsurface is the wheel load area and the distributed load area is equal to the following:DLA 5 W 1 1.75 H! L 1 1.75 H! (1)wher

20、e:DLA = distributed load area, ft2(m2)W = wheel load width, ft (m),L = wheel load length, ft (m), andH = depth of fill, ft (m).4.1.4.3 When several distributed load areas overlap, the total load shall be considered as uniformly distributed over the areadefined by the outside limits of the individual

21、 areas as indicated in Fig. 4. When the dimensions of the com-posite distributed loadarea exceeds the roof area only that portion of the distributed load on the roof area shall be considered in the design.4.1.4.4 The distribution of wheel loads through earth fill may beare neglected when the depth o

22、f fill exceeds 8 ft (2.5 m).4.2 WallsThe design loads for the walls of any structure at or below ground level will consist of surcharge loads resulting fromlive loads, dead loads that can develop as a result of earth pressure, hydrostatic pressure, and construc-tion materials such as usedfor roadway

23、s and walkways. Load diagrams of live load surcharge and dead loads are shown in Fig. 5.4.2.1 Live Loads:4.2.1.1 When traffic can come within a horizontal distance from the structure equal to one half the height of the structure, a liveload surcharge pressure of not less than 0.5 % of the wheel load

24、ing of the traffic involved shouldshall be taken as the live loadacting upon the wall of the structure.4.2.1.2 Surcharge pressures for various live loads transferred to equivalent horizontal fluid pressure are as follows:A-16 16 000 lbf per wheel 3 0.005 = 80 lbf/ft2(3830 Pa) per wheelA-12 12 000 lb

25、f per wheel 3 0.005 = 60 lbf/ft2(2873 Pa) per wheelA-8 8 000 lbf per wheel 3 0.005 = 40 lbf/ft2(1915 Pa) per wheelA-0.3 Refer to 4.2.2.1FIG. 2 Wheel Load AreaC857 12a34.2.1.3 Surcharge pressures resulting from live loads may beare neglected when the distance from ground level exceeds 8 ft (2.5m).4.2

26、.2 Dead Loads:4.2.2.1 The dead loads will consist of an earth pressure above ground water level and hydrostatic pressure plus a modified earthpressure below ground water level. The earth pressure above ground water level and the modified earth pressure below groundwater level will be converted to a

27、horizontal pressure using Rankines Theory on active earth pressure. No structure will bedesigned for less than a 30 lb/ft2(1436 Pa) horizontal pressure.4.2.2.2 For the general case when structures are placed in areas where the soil surface does not slope the horizontal pressureacting at a point on t

28、he wall of the structure above ground water level will be:P 5 Ka3 W 3 H (2)where:P = horizontal pressure, lbf/ft2(Pa)Ka= coefficient of active earth pressure = (1 sin f)/(1 + sinf )f = angle of internal friction of the soil, deg (rad),W = unit weight of soil, lb/ft3(kg/m3) andH = distance from groun

29、d level to the point on the wall under consideration, ft (m).4.2.2.3 In special cases, when structures are placed in areas where the soil surface is sloping, the horizontal pressure acting ata point on the structure above ground water level is as follows:P 5 cos d KaWsH (3)FIG. 3 Distributed Load Ar

30、eaFIG. 4 Overlapping Load AreasC857 12a4where:P = horizontal pressure, lbf/ft2(Pa),Ka= coefficient of active earth pressure =cos dcos d2=cos2d2cos2fcos d1=cos2d2cos2f(4)f = angle of internal friction of the soil, deg (rad),d = angle between the sloping soil surface and the horizontal, deg (rad)Ws= u

31、nit weight of soil, lb/ft3(kg/m3), andH = distance from ground level to the point on the wall under consideration, ft (m).The horizontal pressure below ground water level resulting from the weight of soil above ground water level is equal to thehorizontal pressure at ground water level and will rema

32、in constant from ground water level to the base of structure.FIG. 5 Load Diagrams of Live Load Surcharge and Dead LoadsC857 12a54.2.2.4 The horizontal pressure that can develop below ground water level will consist of a full hydrostatic pressure plushorizontal pressure resulting from the weight of s

33、ubmerged soil. The hydrostatic pressure acting at a point on the wall of thestructure below ground water level is:Pw5 WwHw(5)where:Pw= hydrostatic pressure, lbf/ft2(Pa),Ww= unit weight of water, lb/ft3(kg/m3), andHw= distance from ground water level to the point on the wall under consideration, ft (

34、m).The horizontal pressure acting at a point on the wall of the structure below ground water level resulting from the weight ofsubmerged soil is:Ps5 Ws2 Ww! KaHw(6)where:P = horizontal pressure from submerged soil, lbf/ft2(Pa)WsWw= unit weight of soil less the unit weight of water, lb/ft3(kg/m3),Ka=

35、 coefficient of active earth pressure = (1 sin f)/(1 + sin f),f = angle of internal friction of the soil, deg (rad), andHw= distance from ground water level to the point on the wall under consideration, ft (m).NOTE 3The coefficient of active earth pressure is used for the general case where the soil

36、 surface does not slope.4.3 Base:4.3.1 Live LoadsThe live loads transmitted to the base consist of the maximum value possible of live loads that can beimposed on the roof. This includes the total number of wheel loads that can simultaneously be placed on the structure.4.3.2 Dead LoadsThe dead loads

37、on the base consist of the dead loads imposed on the roof plus the weight of the structureexcluding the base, or the hydrostatic pressure acting on the base, whichever is greater.4.4 Accessories Loading:4.4.1 Cable Pulling DevicesCable pulling devices in all structures are designed for the working l

38、oads specified by the specificuser. These working loads can be compensated for in the design of the structure and are considered in addition to the design loads.4.4.2 Lifting InsertsLifting inserts in all structures are designed for a load equivalent to four times the weight of the structure,utilizi

39、ng no more than three lifting points.maximum load transmitted to the insert. The loads imposed at the lifting points areconsidered in the design of the structure.4.4.3 Equipment Mounting DevicesThe structure is designed to accommodate loads induced by the equipment installed onthe mounting device, a

40、s required by the user. These loads are considered in the design of the structure.5. Significance and Use5.1 This practice is intended to standardize the minimum structural design loading for underground precast concrete utilitystructures.5.2 The user shall verify the anticipated field conditions an

41、d requirements with design loads greater than those specified in thisstandard.6. Keywords6.1 minimum structural design criteria; precast concrete; underground utility enclosuresC857 12a6ASTM International takes no position respecting the validity of any patent rights asserted in connection with any

42、item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical c

43、ommittee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at

44、a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Dr

45、ive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).C857 12a7

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1