ASTM D1102-1984(2013) Standard Test Method for Ash in Wood《木材中灰分的标准试验方法》.pdf

1、Designation: D1102 84 (Reapproved 2013) Modification ofTechnical Association of Pulp and Paper IndustryStandard Method T 211 OM-80Standard Test Method forAsh in Wood1This standard is issued under the fixed designation D1102; the number immediately following the designation indicates the year oforigi

2、nal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of ash,expressed as th

3、e percentage of residue remaining after dryoxidation (oxidation at 580 to 600C), of wood or woodproducts.1.2 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and

4、 health practices and determine the applica-bility of regulatory limitations prior to use.2. Significance and Use2.1 The ash content is an approximate measure of themineral content and other inorganic matter in wood.3. Apparatus3.1 Crucibles, with tightly fitting lids, having a capacity of30 mL or m

5、ore, shall be used. Platinum crucibles are preferred,but silica or porcelain crucibles may be used.3.2 Muffle FurnaceAn electric furnace is recommendedfor igniting the wood sample. A furnace fitted with an indicat-ing pyrometer, so that the desired temperature can bemaintained, is preferable.3.3 Ana

6、lytical Balance, sensitive to 0.1 mg.3.4 Drying Oven, with temperature controlled between 100and 105C.4. Test Specimen4.1 The test specimen shall consist of approximately 2 g ofwood that has been ground to pass a No. 40 (425-m) sieve.Care shall be taken to ensure that it is representative of theenti

7、re lot of material being tested.5. Procedure5.1 Ignite the empty crucible and cover over a burner or inthe muffle at 600C, cool in a desiccator, and weigh to thenearest 0.1 mg. Place the 2-g test specimen in the crucible,determine the weight of crucible plus specimen, and place inthe drying oven at

8、100 to 105C with the crucible coverremoved. After 1 h, replace the cover on the crucible, cool ina desiccator, and weigh. Repeat the drying and weighing untilthe weight is constant to within 0.1 mg. During the cooling andweighing periods, keep the crucible covered to prevent absorp-tion of moisture

9、from the air. Record the weight (crucible plusspecimen minus weight of crucible) as the weight of theoven-dry test specimen.5.2 Place the crucible and contents, with the cover removed,in the muffle furnace and ignite until all the carbon iseliminated. Heat slowly at the start to avoid flaming and pr

10、otectthe crucible from strong drafts at all times to avoid mechanicalloss of test specimen. The recommended temperature of finalignition is 580 to 600C. Avoid heating above this maximum.5.3 Remove the crucible with its contents to a desiccator,replace the cover loosely, cool, and weigh accurately. R

11、epeatthe heating for 30-min periods until the weight after cooling isconstant to within 0.2 mg.6. Calculations and Report6.1 Calculate the percentage of ash, based on the weight ofthe moisture-free wood, as follows:Ash, % 5 W1/W2! 3100 (1)where:W1= weight of ash, andW2= weight of oven-dry sample.6.2

12、 Report the results to two decimal places.7. Precision and Bias27.1 Data obtained by testing 60 wood samples in onelaboratory gives a repeatability as ash content of 0.03 % and as1This test method is currently under the jurisdiction of ASTM Committee D07on Wood and is the direct responsibility of Su

13、bcommittee D07.01 on FundamentalTest Methods and Properties.Current edition approved Aug. 1, 2013. Published September 2013. Originallyapproved in 1950. Last previous edition approved in 2007 as D1102 84 (2007).DOI: 10.1520/D1102-84R13.2Data in this section was obtained from the Technical Associatio

14、n of the Pulpand Paper Industry, P.O. Box 105113, Atlanta, GA 30348.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1a percentage of ash content of 6.6 %. The range of ash contentwas from 0.16 % to 0.84 %.7.2 Reproducibility and compar

15、ability data are not avail-able.8. Keywords8.1 ash; wood productsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any su

16、ch patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invit

17、ed either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a

18、 fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this

19、 standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1102 84 (2013)2