ASTM D1489-2009 Standard Test Method for Nonvolatile Content of Aqueous Adhesives《含水胶粘剂中不挥发物含量的标准试验方法》.pdf

1、Designation: D1489 09Standard Test Method forNonvolatile Content of Aqueous Adhesives1This standard is issued under the fixed designation D1489; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in

2、 parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense. This test method replaces Method 4021 of FederalTest Method Standard No. 1

3、75a.1. Scope1.1 This test method covers the determination of the non-volatile content of aqueous adhesives, such as dextrin, starch,casein, and animal gelatin.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standar

4、d does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM

5、 Standards:2D907 Terminology of Adhesives3. Terminology3.1 DefinitionsMany terms in this test method are definedin Terminology D907.4. Significance and Use4.1 Adhesive cost is often related to the solids level (non-volatile content).4.2 This test method can be used to compare the nonvolatilecontent

6、of various adhesives for adhesive selection and productuniformity.4.3 This test method is suitable for quality control andresearch purposes.5. Apparatus and Materials5.1 Analytical Balance, for weighing of specimen, accurateto 60.001 g.5.2 Laboratory Balance, for weighing of sample, accurateto 60.01

7、 g.5.3 Constant-Temperature Oven, capable of maintaining atemperature of 105 6 1C (221 6 2F).5.4 Glass Jar of sufficient size, 1 L or more, to store sampleof adhesive prior to testing. The jar shall be such that it can besealed to prevent the loss of volatile content during the storageperiod.5.5 Bea

8、kerof 100 mL capacity.5.6 Weighing Bottleswide-mouth cylindrical glass weigh-ing bottles, of flat form, about 30 mm in height and 50 mm indiameter, having interchangeable ground-in glass caps.5.7 Volumetric Flasks, of 200-mL capacity, with glass stop-pers.5.8 Volumetric Pipet, of 10-mL capacity.5.9

9、Desiccator, with drying agent and tray.5.10 Silica Sand.5.11 Water, Hotdistilled water heated to at least 80C.5.12 Hot Plate, used to heat the water.6. Sampling6.1 The sample of the adhesive shall be representative of thelot being evaluated. The quantity shall be at least 1.0 L aliquotconsisting of

10、a composite taken, when possible, from three ormore separate containers chosen at random. Thoroughly mixthe sample to uniform consistency. Immediately place thecomposite sample in an airtight glass jar until tested.7. Procedure7.1 Make sure that the sample in the glass jar is of uniformconsistency b

11、efore removing a specimen for testing. Inspectthe sample to ensure that there are no signs of settling orseparation of the adhesive. If settling or separation are noted,mix the samples thoroughly. Other factors, such as foaming orcontamination may require the samples be replaced.7.2 Test three 10-g

12、specimens from each composite sample.7.3 Weigh about 10 g of adhesive into a small beaker to thenearest 0.01 g. Disperse in 50 mL of hot distilled water andtransfer to a 200-mL volumetric flask. Rinse the beaker withsmall portions of hot distilled water and add rinsings to theflask. Dilute to mark w

13、ith hot distilled water. Perform duplicatetests on each dispersion prepared in this manner.1This test method is under the jurisdiction of ASTM Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.10 on WorkingProperties.Current edition approved Dec. 1, 2009. Published Janua

14、ry 2010. Originallyapproved in 1957. Last previous edition approved in 2004 as D1489 97 (2004).DOI: 10.1520/D1489-09.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to

15、 the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.7.4 Pipet 10 mL of the dispersion into a tared weighingbottle three quarters full of silica sand which has been dried toconstant

16、weight.NOTE 1In the case of adhesives that do not reach constant weight, forexample those containing glycerin or slightly volatile plasticizers, makeone weighing after a specified period of time mutually agreed uponbetween the manufacturer and the purchaser.7.5 Dry the sample in the bottle at 105 6

17、1C (221 6 2F)in the constant temperature oven until it has reached a constantweight. Determine this by removing the bottle, at predeter-mined times, and quickly weighing it on the scale. Once thesame weight is achieved in two consecutive weighings, returnthe sample to the oven for 5 min more. Then,

18、cover the bottleand cool in a desiccator charged with desiccant to roomtemperature before weighing to the nearest 0.001 g.8. Calculation8.1 Calculate the percent of nonvolatile content as follows:Nonvolatile matter, % 5 W1/W2! 3 2000where:W1= weight of dried residue, andW2= weight of original 10-g s

19、pecimen.9. Accuracy of Test9.1 Repeat the tests once if the results obtained in the sixtests on a sample cover a range of more than 2 percentageunits.10. Report10.1 Report the following information:10.1.1 Complete identification of the adhesive tested, in-cluding type, source, manufacturers code num

20、ber, lot or batchnumber, condition, and date.10.1.2 Number of containers received and number sampled.10.1.3 Number of specimens tested (only if retested inaccordance with Section 9).10.1.4 Average non-volatile content, in percent, and samplestandard deviation. If a retest is made, report each set of

21、 resultsseparately.11. Precision and Bias11.1 No precision or bias exists for this test method, as thenecessary resources for round-robin testing have not beenforthcoming.12. Keywords12.1 nonvolatile; nonvolatile content; solids; solids contentASTM International takes no position respecting the vali

22、dity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subj

23、ect to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquar

24、ters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standar

25、d is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1489 092